Skip to content
KickTyres
CriticalCommonEngine

Nissan Juke: MR16DDT Turbocharger Bearing Oil Starvation Failure

MR16DDT Turbocharger Bearing Oil Starvation Failure is a common engine fault on the Nissan Juke on the 2011–2019 cars, and we rate it critical. Putting it right costs ≈A$2,210 to ≈A$5,060 at independent workshop rates, shown as an approximate guide in Australian dollars. Below is what goes wrong, the symptoms to notice on a test drive, where to look, and what to ask the seller before you hand over any money. It is one of 22 documented faults on the Nissan Juke.

Vehicle
Nissan Juke
Engine
MR16-DDT
Years
2011–2019
Fuel
petrol
System
Engine

This page covers the Nissan Juke as a model. Some faults only affect particular engines or build years — enter a plate below to narrow the list to one car.

All Nissan Juke faults22 documented faults on this model

What you are looking at

No photograph available

We do not hold a verified photograph of the Turbocharger yet. We would rather show none than show a picture of a different part.

What goes wrong

The MR16DDT turbocharger relies on pressurised engine oil fed through a dedicated feed line to lubricate the centre bearing cartridge. Carbon deposits from degraded oil accumulate in the narrow oil feed passage and restrict flow, starving the bearing of lubrication during high-load operation and causing the bearing to overheat and seize. This failure mode is accelerated by extended oil change intervals, short urban drive cycles that never fully heat the oil, and immediate engine shutoff after hard driving without an idle-down period to allow the turbo to cool.

What you would notice

  • Blue-grey smoke from the exhaust on startup and under hard acceleration, indicating oil burning in the turbine housing
  • High-pitched whine or metallic rattling from the turbocharger under boost that worsens over time
  • Noticeable loss of boost pressure and sluggish acceleration above 3000 rpm
  • Elevated oil consumption without visible external leaks

How to check it

Where to look. Turbocharger mounted on the exhaust manifold, passenger side of the MR16DDT engine bay

Spin the compressor wheel by hand and feel for shaft play or roughness. Check for blue-grey exhaust smoke at startup and under acceleration. Inspect oil fill cap and dipstick for signs of combustion gases (foaming, emulsification). If a workshop inspection is possible: Remove the turbo oil feed banjo and check for carbon fouling or restricted flow.

Parts involved: Turbocharger.

What it costs to put right

≈A$2,210 to ≈A$5,060 at independent workshop rates, shown as an approximate guide in Australian dollars. That is for this job on its own, not for the car.

An estimate, converted to Australian dollars, for the repair as normally carried out. What a specific car costs depends on which part has failed and what it damaged on the way — treat this as the floor for a negotiation, not a quote.

Ask the seller

  • “Has the turbocharger ever been replaced or rebuilt, and can you show service records?”
  • “What oil change interval has been followed, and which oil specification was used?”
  • “Does the car smoke at cold start or under hard acceleration?”

Now check the Nissan Juke you are actually looking at

Everything above is true of the model, and it is free. What it does not tell you is whether THIS car still has money owing on it, has been written off or reported stolen, what kms it showed in past sale ads, whether it has had accident repair claims and what it is worth today. That comes from the official records for that plate. Enter the plate and its state for the A$17.90 Vehicle Check, or the full history from A$24.99.

Where this comes from

The failure described above is documented in published sources — owner forums, technical service bulletins, recall notices and workshop write-ups — held in our fault database. The inspection instructions and the cost estimate are KickTyres’ own interpretation of them, and it is a starting point for an inspection rather than a manufacturer statement.

Nissan Juke buyer questions

Is mr16ddt turbocharger bearing oil starvation failure serious on a Nissan Juke?

We rate it critical and common on the Nissan Juke. The MR16DDT turbocharger relies on pressurised engine oil fed through a dedicated feed line to lubricate the centre bearing cartridge. Carbon deposits from degraded oil accumulate in the narrow oil feed passage and restrict flow, starving the bearing of lubrication during high-load operation and causing the bearing to overheat and seize. This failure mode is accelerated by extended oil change intervals, short urban drive cycles that never fully heat the oil, and immediate engine shutoff after hard driving without an idle-down period to allow the turbo to cool.

How much does it cost to fix on a Nissan Juke?

≈A$2,210 to ≈A$5,060 at independent workshop rates, shown as an approximate guide in Australian dollars. That figure is for this job on its own. A car showing the symptoms on this page is usually worth either walking away from or negotiating down by at least the repair figure.

Which Nissan Juke years are affected?

Our research records this fault on the 2011–2019 Nissan Juke. Build dates move around, especially on imported cars, so treat the range as the years to look hardest at rather than a guarantee either way. The official records tell you the exact build and first registration date for the car in front of you.

How do I check for it before I buy?

Spin the compressor wheel by hand and feel for shaft play or roughness. Check for blue-grey exhaust smoke at startup and under acceleration. Inspect oil fill cap and dipstick for signs of combustion gases (foaming, emulsification). If a workshop inspection is possible: Remove the turbo oil feed banjo and check for carbon fouling or restricted flow. Look here: Turbocharger mounted on the exhaust manifold, passenger side of the MR16DDT engine bay