Toyota Supra: Front lower ball joint wear — heavy nose loading
Front lower ball joint wear — heavy nose loading is a common suspension fault on the Toyota Supra on the 1993–2002 cars, and we rate it major. Putting it right costs ≈A$410 to ≈A$1,010 at independent workshop rates, shown as an approximate guide in Australian dollars. Below is what goes wrong, the symptoms to notice on a test drive, where to look, and what to ask the seller before you hand over any money. It is one of 23 documented faults on the Toyota Supra.
- Vehicle
- Toyota Supra
- Years
- 1993–2002
- Fuel
- petrol
- System
- Suspension
What you are looking at
Example of the part — not this vehicleA separated lower ball joint: the control arm has dropped and the wheel has splayed out under the guard.
What goes wrong
The A80 Supra carries significant front-end weight from the heavy inline-six engine, which accelerates wear on the front lower control arm ball joints. Worn ball joints create a handling shimmy and can ultimately result in loss of steering control if ignored. This is a common finding on roadworthy inspections of higher-mileage A80s in Australia. Many imported examples have worn or previously bodged ball joints.
What you would notice
- Clunking from front suspension over bumps or during steering input
- Vague or wandering steering feel
- Uneven tyre wear on front axle
- Roadworthy failure for excessive ball joint play
How to check it
Where to look. Front lower control arms, one ball joint per side
Visually inspect the ball joint boot for cracking or grease loss. Check for any scoring or pitting on the ball joint itself. If a workshop inspection is possible: With the car on a hoist, grab each front wheel at the 6 and 12 o'clock positions and check for vertical play.
What it costs to put right
≈A$410 to ≈A$1,010 at independent workshop rates, shown as an approximate guide in Australian dollars. That is for this job on its own, not for the car.
Ask the seller
- “When were the front ball joints last replaced?”
- “Has the car had a recent roadworthy, and did it pass first time?”
- “Is there any clunking from the front suspension?”
Now check the Toyota Supra you are actually looking at
Everything above is true of the model, and it is free. What it does not tell you is whether THIS car still has money owing on it, has been written off or reported stolen, what kms it showed in past sale ads, whether it has had accident repair claims and what it is worth today. That comes from the official records for that plate. Enter the plate and its state for the A$17.90 Vehicle Check, or the full history from A$24.99.
Where this comes from
Toyota Supra buyer questions
Is front lower ball joint wear — heavy nose loading serious on a Toyota Supra?
We rate it major and common on the Toyota Supra. The A80 Supra carries significant front-end weight from the heavy inline-six engine, which accelerates wear on the front lower control arm ball joints. Worn ball joints create a handling shimmy and can ultimately result in loss of steering control if ignored. This is a common finding on roadworthy inspections of higher-mileage A80s in Australia. Many imported examples have worn or previously bodged ball joints.
How much does it cost to fix on a Toyota Supra?
≈A$410 to ≈A$1,010 at independent workshop rates, shown as an approximate guide in Australian dollars. That figure is for this job on its own. A car showing the symptoms on this page is usually worth either walking away from or negotiating down by at least the repair figure.
Which Toyota Supra years are affected?
Our research records this fault on the 1993–2002 Toyota Supra. Build dates move around, especially on imported cars, so treat the range as the years to look hardest at rather than a guarantee either way. The official records tell you the exact build and first registration date for the car in front of you.
How do I check for it before I buy?
Visually inspect the ball joint boot for cracking or grease loss. Check for any scoring or pitting on the ball joint itself. If a workshop inspection is possible: With the car on a hoist, grab each front wheel at the 6 and 12 o'clock positions and check for vertical play. Look here: Front lower control arms, one ball joint per side