Skip to content
KickTyres
CriticalCommonEngine

Audi Q3: 2.0 TFSI Timing Chain Tensioner Failure

2.0 TFSI Timing Chain Tensioner Failure is a common engine fault on the Audi Q3 on the 2011–2015 cars, and we rate it critical. Putting it right costs $1,800 to $5,500 at New Zealand independent workshop rates. Below is what goes wrong, the symptoms to notice on a test drive, where to look, and what to ask the seller before you hand over any money. It is one of 13 documented faults on the Audi Q3.

Vehicle
Audi Q3
Engine
2.0L
Years
2011–2015
Fuel
petrol
System
Engine

This page covers the Audi Q3 as a model. Some faults only affect particular engines or build years — enter a plate below to narrow the list to one car.

All Audi Q3 faults13 documented faults on this model

What you are looking at

The front of a dual overhead camshaft engine with the timing cover removed, exposing the timing chain and sprockets.Example of the part — not this vehicle

The front of a twin-cam engine with the timing cover off — chain, sprockets and guides.

Logansenf · CC BY-SA 4.0 · Wikimedia Commons

What goes wrong

The CCZC 2.0 TFSI engine uses a hydraulic timing chain tensioner that loses pressure when oil is cold or degraded, allowing the chain to slap and skip. On early 8U-generation Q3s this is a documented failure mode — the tensioner plastic ratchet can crack, the chain stretches prematurely, and if unaddressed the timing jumps and bends valves. Audi issued a revised tensioner (part 06H109467N) and updated the oil-spec requirement, but many vehicles remain on the original unit.

What you would notice

  • Rattling or ticking noise on cold start that fades after 5-10 seconds
  • Check engine light with cam/crank timing correlation codes (P0016, P0017)
  • Rough idle or misfires on start-up in cold weather
  • Loss of power or engine stumble if chain has skipped a tooth
  • Oil pressure warning light appearing at idle after long oil change intervals

How to check it

Where to look. Front of engine block, behind the timing cover on the passenger side

  1. Cold-start the engine and listen for a metallic rattling from the front of the engine lasting more than 2-3 seconds before quietening.

  2. Check oil service history — extended intervals accelerate tensioner failure.

  3. Ask for evidence of tensioner replacement or inspection; scan for cam/crank correlation fault codes P0016/P0017.

Parts involved: Timing chain.

What it costs to put right

$1,800 to $5,500 at New Zealand independent workshop rates. That is for this job on its own, not for the car.

An estimate, in NZD, for the repair as normally carried out. What a specific car costs depends on which part has failed and what it damaged on the way — treat this as the floor for a negotiation, not a quote.

Ask the seller

  • “Has the timing chain tensioner ever been inspected or replaced, and do you have a receipt?”
  • “What oil grade and change interval has been used — was it always 5W-30 or better at or under 10,000 km?”
  • “Has the car ever shown a check engine light related to timing or misfires on cold start?”

Now check the Audi Q3 you are actually looking at

Everything above is true of the model, and it is free. What it does not tell you is whether THIS car has been looked after: its odometer history and whether the reading has ever gone backwards, whether there is still money owing on it, whether it has been reported stolen, how many owners it has had and what it is really worth today. That comes from the official records for that plate. Enter the plate for the free details, or get the full history and a market valuation from $13.49.

Not sure what you would be paying for? See what a full KickTyres check includes.

Where this comes from

The failure described above is documented in published sources — owner forums, technical service bulletins, recall notices and workshop write-ups — held in our fault database. The inspection instructions and the cost estimate are KickTyres’ own interpretation of them, and it is a starting point for an inspection rather than a manufacturer statement.

Audi Q3 buyer questions

Is 2.0 tfsi timing chain tensioner failure serious on a Audi Q3?

We rate it critical and common on the Audi Q3. The CCZC 2.0 TFSI engine uses a hydraulic timing chain tensioner that loses pressure when oil is cold or degraded, allowing the chain to slap and skip. On early 8U-generation Q3s this is a documented failure mode — the tensioner plastic ratchet can crack, the chain stretches prematurely, and if unaddressed the timing jumps and bends valves. Audi issued a revised tensioner (part 06H109467N) and updated the oil-spec requirement, but many vehicles remain on the original unit.

How much does it cost to fix on a Audi Q3?

$1,800 to $5,500 at New Zealand independent workshop rates. That figure is for this job on its own. A car showing the symptoms on this page is usually worth either walking away from or negotiating down by at least the repair figure.

Which Audi Q3 years are affected?

Our research records this fault on the 2011–2015 Audi Q3. Build dates move around, especially on imported cars, so treat the range as the years to look hardest at rather than a guarantee either way. The official records tell you the exact build and first registration date for the car in front of you.

How do I check for it before I buy?

Cold-start the engine and listen for a metallic rattling from the front of the engine lasting more than 2-3 seconds before quietening. Check oil service history — extended intervals accelerate tensioner failure. Ask for evidence of tensioner replacement or inspection; scan for cam/crank correlation fault codes P0016/P0017. Look here: Front of engine block, behind the timing cover on the passenger side