Skip to content
KickTyres
Holden1995–2017 Critical issues documented

Holden Statesman WM: common faults & what to check

The WM is the Holden Statesman built 2006–2017. The engines documented for it are the 3.6 V6 petrol and 6.0 V8 petrol. Of the 13 faults documented for the Statesman, 4 apply to this generation, each with its symptoms, what to inspect and a typical repair cost. Free, no account needed.

Check this exact Holden Statesman

  • Money owing
  • Written off
  • Accident claims
  • Odometer history

An Australian plate goes to the A$17.90 Vehicle Check: money owing, write-off, stolen and rego. Full History adds past kms, accident claims and market value from A$24.99. The free fault check for this model needs the generation and engine, pick them below.

13

Documented faults

Critical

Most serious

≈A$1,100–3,220

Typical repair

33

Service milestones

You're looking at the WM

2 engine variants are documented for this generation. Pick yours to narrow further, or keep reading for the generation as a whole.

Choose a different generation

Now narrow it to the engine

A 1.8 and a 2.4 of the same car do not fail the same way, so the faults below narrow to the engine as well as the year. Free, no account needed.

A 2007 Holden Statesman is the WM generation (2006 to 2017).

Start your free check on this Holden Statesman

No plate needed. You get the risk score, the buyer's checklist and the guided inspection for the exact car you picked above — not the whole nameplate.

Holden Statesman WMEngine not picked yet

Pick the engine above first: the Statesman came with 2, and without it the report has to show all of their faults. Pick the engine

Free. The paid plate check is separate, and stays optional.

Can't confirm for this car

Holden Statesman · 2007

Narrowed to the year. No engine is recorded for this vehicle. Pick an engine to see which faults apply.

Tell us the engine, or check the engine code on the car, before relying on this.

  • No engine is recorded for this vehicle.

matched on year only

What to look out for

The checks worth doing on a Holden Statesman before you hand over any money. Every documented fault is listed below, each with its own page.

  • Costly issue

    Inspect coolant colour and level.

    See why

    Plastic Radiator End-Tank Failure and Coolant Loss

    The WH and WK Statesman and Caprice radiators use aluminium core construction with crimped plastic end tanks. The plastic tanks are subject to long-term thermal cycling stress and become brittle with age, developing cracks at the crimp seams particularly at the lower tank. Failure results in rapid coolant loss and, if not caught immediately, engine overheating. The L76 6.0L in the WL is particularly intolerant of overheating due to its aluminium block and heads. Inspection of the tank-to-core crimp joint for weeping, staining, or visible cracking is recommended on any example over 130,000 km. Replacement with an all-aluminium radiator is preferred over OEM-specification plastic-tank units.

    What you would notice

    • Engine overheating under load
    • Coolant loss or steam from engine bay

    Typically ≈A$770–1,550 to put right.

All 4 issues for this one

Documented for the exact year and engine you picked. Tap an area to open it.

Engine, transmission & cooling1

01Plastic Radiator End-Tank Failure and Coolant Loss

Inspect coolant colour and level.petrolCooling
CommonCooling ≈A$770–1,550 to fix

The WH and WK Statesman and Caprice radiators use aluminium core construction with crimped plastic end tanks. The plastic tanks are subject to long-term thermal cycling stress and become brittle with age, developing cracks at the crimp seams particularly at the lower tank. Failure results in rapid coolant loss and, if not caught immediately, engine overheating. The L76 6.0L in the WL is particularly intolerant of overheating due to its aluminium block and heads. Inspection of the tank-to-core crimp joint for weeping, staining, or visible cracking is recommended on any example over 130,000 km. Replacement with an all-aluminium radiator is preferred over OEM-specification plastic-tank units.

Symptoms to notice

  • Engine overheating under load
  • Coolant loss or steam from engine bay

What to check

  1. Inspect coolant colour and level.
  2. Check for white exhaust smoke or sweet smell indicating coolant in combustion.
  3. If a workshop inspection is possible: Pressure test the system.

Parts involved: Radiator.

Only with a certain gearbox: 1 issueEach one names the gearbox it affects, for example the CVT automatic. Check which gearbox this car has.

016L80 6-speed automatic torque-converter shudder and harsh shifts

On the test drive cruise gently at 60-90km/h and feel for a shudder as the transmission locks up.2006–2017Transmission
OccasionalTransmission ≈A$370–3,220 to fix

Can't confirm for this car

WM/WN models use the GM 6L80 6-speed auto, which is generally strong but is known for a torque-converter-clutch 'shudder' - a vibration you feel at light throttle around 60-90km/h as the converter locks up - and harsh or flaring shifts when the fluid is old or the valve body wears. A fluid and filter service often improves it, but a neglected unit with a shudder can need converter or valve-body work.

A cutaway automatic transmission torque converter showing the internal turbine and stator.Example of the part — not this vehicle

A torque converter, sectioned. The lock-up clutch inside is what shudders.

No machine-readable author provided. BerndB~commonswiki assumed (based on copyright claims). · CC BY-SA 3.0 · Wikimedia Commons

Symptoms to notice

  • Shudder or vibration cruising at light throttle (feels like driving over rumble strips)
  • Harsh or flaring gear changes
  • Delayed engagement into Drive or Reverse
  • Slipping on take-off

What to check

On the test drive cruise gently at 60-90km/h and feel for a shudder as the transmission locks up. Feel each shift for harshness or slip. Ask when the transmission fluid and filter were last changed - many owners never do it. Have it scanned for transmission codes.

Where to look: Automatic gearbox behind the engine

Parts involved: Torque converter.

Ask the seller

  • “Has the transmission fluid and filter ever been changed?”
  • “Does it shudder or vibrate when cruising at light throttle?”
Depends on the exact engine or version: 2 issuesDocumented for a specific engine or version we could not confirm from what you picked. Check the engine code on the car.

016.0 V8 (L98/L77) piston slap and Active Fuel Management oil use/lifter wear

Ask how much oil it uses between services - a thirsty AFM V8 is a warning sign.petrol2006–2017Engine
OccasionalEngine ≈A$1,380–4,600 to fix

Can't confirm for this car

The V8 WM/WN Caprice/Statesman used the 6.0 Gen-IV V8 (L98, then L77 with Active Fuel Management). The L77 can drink oil and suffer AFM-related lifter and valvetrain problems - AFM shuts down cylinders to save fuel and the collapsible AFM lifters are a known weak point, sometimes causing a misfire, ticking and heavy oil consumption. These V8s also commonly show light cold-start piston slap that is usually harmless. AFM lifter/oil issues, though, can be a costly top-end repair.

Symptoms to notice

  • Ticking or misfire from the V8, sometimes with a check-engine light
  • Higher-than-expected oil consumption
  • Light rattle on cold start (piston slap - usually harmless)
  • Rough running when it switches cylinder modes

What to check

  1. Ask how much oil it uses between services - a thirsty AFM V8 is a warning sign.
  2. Listen for ticking at idle and a misfire.
  3. Check whether AFM has been disabled/deleted (some owners do this to protect the engine) and for any lifter work in the history.

Where to look: Top end of the V8 engine - lifters and valvetrain

Ask the seller

  • “How much oil does the V8 use between services?”
  • “Has it ever had lifter or AFM-related work, or been AFM-deleted?”

023.6 Alloytec/SIDI V6 timing chain stretch from oil sludge

Start the engine from cold and listen for a rattle from the timing (front) end that quietens after a few seconds.petrol2006–2017EngineRead the full fault: symptoms, where to look, what to ask the seller
Other Holden Statesman engines and years9 documented issues that do not apply to the one you picked.
Engine, transmission & cooling6

01Hydraulic lifter ticking and collapse (6.0 L76/L77 V8, WM Statesman)

Check for oil leaks around valve covers, sump and gaskets.petrol2009–2013Engine
CommonEngine ≈A$5,470–10,950 to fix

Does not apply

The 6.0 L76 and L77 V8 in the WM Statesman (2009 on) uses Active Fuel Management, which relies on special hydraulic lifters to shut down four cylinders under light load. These lifters are known for ticking at start-up (GM bulletin 10-06-01-007B) and, in worse cases, collapsing. A collapsed lifter can shed metal through the oil system and damage the camshaft and bearings, and engines with metal in the sump usually need a rebuild. The common fix is solid lifters with a non AFM camshaft and a retune.

Symptoms to notice

  • Evidence of engine wear or deterioration
  • Warning light or abnormal behaviour noted during operation

What to check

  1. Check for oil leaks around valve covers, sump and gaskets.
  2. Inspect coolant condition and level.

025.7 LS1 V8 oil starvation from the local sump / no low-oil warning

Check the dipstick is at full before you drive - this engine punishes low oil.petrol2000–2006Engine
OccasionalEngine ≈A$2,760–8,280 to fix

Does not apply

The V8 WH/WK Statesman uses the 5.7 LS1, but the Australian cars were fitted with a local sump that deleted the low-oil-level warning light the US engines had, and positions the oil pickup at the front of the sump. If the oil is a bit low, hard acceleration or a firm stop can uncover the pickup and let it suck air, and even a short run with low oil can starve and wreck the bottom-end bearings. Because there's no warning light, an owner can run it low without knowing. These engines can also show light 'piston slap' rattle on cold start, which is usually cosmetic.

Symptoms to notice

  • Deep knocking from the bottom of the engine (bearing damage)
  • Light metallic rattle on cold start that fades when warm (piston slap - usually harmless)
  • Low oil on the dipstick
  • Oil-pressure warning under hard driving or braking

What to check

  1. Check the dipstick is at full before you drive - this engine punishes low oil.
  2. Listen on cold start for a light slap (usually ok) versus a deep knock under load (serious).
  3. Ask the owner how carefully they keep the oil topped up, since there is no low-oil warning light.
  4. Any oil-pressure light is a walk-away.

Where to look: V8 engine sump and bottom end; oil pickup at the front of the sump

Ask the seller

  • “How do you keep an eye on the oil level given there's no warning light?”
  • “Has it ever shown an oil-pressure light or run low on oil?”

034L60E Automatic 3-4 Clutch Pack Failure

During test drive at highway speed, confirm smooth and positive 3-4 upshift.petrol2000–2006TransmissionRead the full fault: symptoms, where to look, what to ask the seller

04Hydraulic lifter failure and valvetrain damage (5.7 LS1 V8)

Listen at idle, cold and warm, for a tapping or ticking from the top of the engine that does not fade.petrol1999–2003Engine
OccasionalEngine ≈A$2,300–6,440 to fix

Does not apply

The 5.7 LS1 V8 in the WH Statesman and Caprice is a known issue for hydraulic roller lifter failure, where the plunger sticks collapsed, the spring jams or the roller is starved of oil. A failed lifter can bend a pushrod and go on to break rockers or valves and damage the camshaft. Specialists suggest replacing lifters at about 100,000 km. No recall or extended warranty applies.

Symptoms to notice

  • Persistent tapping or ticking from the top of the engine
  • Misfire or rough idle
  • Check engine light with misfire codes

What to check

  1. Listen at idle, cold and warm, for a tapping or ticking from the top of the engine that does not fade.
  2. Feel for a misfire on the test drive and watch for the check engine light.
  3. Ask whether the valve gear has been replaced and at what km.
  4. If a workshop inspection is possible: have a scan for misfire codes, and if a tick is present have the rocker covers removed to check pushrods and lifters.

Where to look: Engine valvetrain in the block valley

Ask the seller

  • “Have the lifters or camshaft been replaced, and at what km?”
  • “Does it tick at idle?”

05Oil consumption (5.7 LS1 V8, early WH Statesman)

Cold-start the engine and watch exhaust for blue smoke.petrol1999–2003EngineRead the full fault: symptoms, where to look, what to ask the seller

063.8 V6 Ecotec misfire from spark plugs, coils and plastic intake

Feel for a rough or shaky idle and any hesitation accelerating.petrol2000–2006Engine
CommonEngine ≈A$230–830 to fix

Does not apply

The 3.8 V6 (Ecotec/Series II supercharged on some) in the WH/WK Statesman reliably fouls or wears its spark plugs around 80,000km and starts to misfire - it won't always log a fault code, so a rough-running V6 with an ageing tune-up is common. Coil packs and the plastic intake manifold components also age and can cause misfires and small coolant weeps. It's cheap to put right but easy to overlook when buying.

Symptoms to notice

  • Rough idle or slight shake, especially warm
  • Hesitation or flat spot under acceleration
  • Occasional misfire without a dash light
  • Small coolant weep near the inlet manifold

What to check

  1. Feel for a rough or shaky idle and any hesitation accelerating.
  2. Ask when the spark plugs, leads and coils were last done - if it's been over 80,000km, budget for a tune-up.
  3. Check the service book and look for coolant staining around the plastic intake.

Where to look: Spark plugs, leads and coils on the V6 engine; plastic intake manifold on top

Parts involved: Intake manifold, Ignition coil.

Ask the seller

  • “When were the spark plugs and coils last replaced?”
  • “Does it ever idle roughly or hesitate?”
Body, brakes, suspension & interior2

01Rear Air Suspension Compressor and Air Bag Failure

Check rear ride height visually — should sit level or near-level with the front.petrol2000–2006SuspensionRead the full fault: symptoms, where to look, what to ask the seller

02Front suspension wear - lower control arm bushes, ball joints and idler

On the test drive listen for clunks over bumps and feel whether the steering is tight or vague.2000–2006Suspension
CommonSuspension ≈A$280–1,660 to fix

Does not apply

The WH/WK Statesman is a big, heavy rear-drive sedan, and the front suspension wears predictably - lower control arm bushes, ball joints, tie-rod ends and (on the steering) idler/pitman components loosen up with age and our roads. Worn parts give vague steering, clunks over bumps and uneven tyre wear, and are a common roadworthy failure. Individually the parts are cheap; a full front-end refresh adds up.

The front wheel of a car splayed outward with the lower control arm hanging down after a ball joint separation.Example of the part — not this vehicle

A separated lower ball joint: the control arm has dropped and the wheel has splayed out under the guard.

Elfix · CC0 · Wikimedia Commons

Symptoms to notice

  • Clunk or knock over bumps and speed humps
  • Vague or wandering steering
  • Uneven wear on the front tyres
  • Shudder through the wheel

What to check

On the test drive listen for clunks over bumps and feel whether the steering is tight or vague. Look at the inner and outer edges of the front tyres for uneven wear. A pre-purchase inspection or roadworthy check will find worn bushes and ball joints. Push down hard on each front corner and watch it settle.

Where to look: Front suspension control arms, ball joints and steering tie-rods under the front of the car

Parts involved: Ball joint.

Ask the seller

  • “When was the front suspension last checked or any bushes/ball joints replaced?”
  • “Does it have a current roadworthy certificate and any advisory notes?”
Fluid leaks1

01Rear main seal oil leak (3.8 Ecotec V6 L36/L67)

Look under the car with a torch at the join between engine and gearbox, and at the front timing cover and rocker covers, for wet oil.petrol1995–1999Fluid Leaks
OccasionalFluid Leaks ≈A$830–2,020 to fix

Does not apply

The 3.8 Ecotec V6 in the VS Statesman and Caprice is a known issue for oil weeping from the rear main crankshaft seal, where the engine meets the gearbox. Front timing cover seals and rocker cover gaskets are the other usual leak points on this engine. The engine itself is generally reliable, but the seal repair can mean removing the transmission. No recall or extended warranty applies.

Symptoms to notice

  • Oil drips under the engine to gearbox join
  • Oily grime on the bellhousing
  • Oil level dropping between services

What to check

  1. Look under the car with a torch at the join between engine and gearbox, and at the front timing cover and rocker covers, for wet oil.
  2. Check the parking spot for drips and the dipstick for a low level.
  3. Ask whether any seals have been replaced.
  4. If a workshop inspection is possible: have the leak traced on a hoist to tell a rear main seal leak from sump, gearbox or power steering leaks.

Where to look: Rear of the engine block at the gearbox join

Parts involved: Rocker / valve cover.

Ask the seller

  • “Has the rear main seal or timing cover seal ever been replaced?”
  • “Does it need oil topped up between services?”

Holden Statesman service schedule

The 2 engines a 2007 Holden Statesman was sold with, each with its own intervals. Pick your engine above to narrow this to one. These are the model’s intervals — the car’s own service book is the only thing that can tell you what has actually been done to it.

Holden Statesman WM · 2006–2010 · 6.0L V8 (L98) - Caprice/Luxury trim

Petrol

Due by distance

  1. 150,000 km

    Evaluate the original suspension bushings and struts to maintain that smooth Statesman ride.

  2. 200,000 km

    Ensure the cooling system - hoses and radiator - has been refreshed to protect the alloy engine.

  3. 250,000 km

    Have the timing chain checked for stretch, a common focus point for high-mileage LS-series engines.

Holden Statesman WM · 2006–2010 · 3.6L V6 (Alloytec) - Standard trim

Petrol

Due by distance

  1. 150,000 km

    Full cooling system refresh including hoses and a water pump check.

  2. 180,000 km

    Ensure the transmission fluid has been serviced if not already documented.

  3. 200,000 km

    Suspension bushings and control arms need watching, as the Statesman's weight leads to natural wear here.

Holden Statesman faults in detail

Narrowed to the Holden Statesman · 2007. Each of these has its own page: the symptoms, where to look, what to ask the seller and what the repair costs. Free, no account needed.

3.6 Alloytec/SIDI V6 timing chain stretch from oil sludgeMajor · Engine

Other Holden models

Holden Commodore55 documented faultsHolden Captiva20 documented faultsHolden Astra18 documented faultsHolden Rodeo12 documented faultsHolden Trax8 documented faultsHolden Caprice6 documented faults

Holden Statesman buyer questions

Is the Holden Statesman reliable?

Like any used car, it depends on the specific example and its service history. Across the 13 documented faults for the Holden Statesman, the recurring problem areas are engine, transmission, and suspension. A Holden Statesman with a full service history and no signs of the issues listed on this page can be a sound buy but each one needs to be checked individually before you commit.

What are the most common problems with a used Holden Statesman?

We've catalogued 13 known faults for the Holden Statesman, covering engine, transmission, and suspension. All 13 are written out in full on this page, with the symptoms to notice, what to inspect, and typical repair costs for each. Free to read, no account needed.

How much do repairs cost on a Holden Statesman?

Most single repairs on the Holden Statesman fall between ≈A$1,100–3,220 at independent-workshop rates (an approximate guide in Australian dollars). Some of the 13 documented faults cost less and a few cost considerably more, and no one car needs them all. Knowing which ones to look for before you view is what lets you negotiate the price down or walk away.

Should I get a pre-purchase inspection on a Holden Statesman?

Yes. A Holden Statesman inspection focused on its known weak points is the single best way to avoid an expensive mistake. KickTyres gives you a guided, model-specific inspection with AI photo analysis from A$28.90, far less than the cost of missing one of the faults on this page. For a big purchase, a mechanic's pre-purchase inspection on the car you settle on is still worth it.