BMW 2 Series F22: common faults & what to check

Does not apply

The S55 3.0-litre twin-turbocharged inline-six in the M2 (and M3/M4) is a high-performance engine that requires meticulous oil maintenance. Main bearing wear is documented at high mileages on vehicles that have been used hard or tracked, especially where oil-change intervals were stretched. The S55 crankshaft main bearings are relatively thin and the engine runs high oil temperatures under spirited driving. Bearing knock at cold start or under load is the primary symptom. This fault is well-documented on international M2/M3/M4 forums and has resulted in multiple engine rebuilds. BMW did not issue a recall but acknowledged oil degradation accelerates bearing wear in the S55.

Where to look: Engine bottom end — crankshaft main bearing journals inside the block

Does not apply

The first-generation B58 (B58A) builds its crankcase ventilation (PCV) valve into the plastic valve cover, using a spring-loaded rubber diaphragm to control crankcase pressure. The diaphragm wears or tears, which lets oily vapour into the intake and can cause whistling, rough idle, smoke and higher oil use; separately the valve cover gasket hardens and seeps oil. BMW sells a diaphragm repair kit for the B58A, but many cars end up with a whole new valve cover. Owner reports on Bimmerpost include a 340i needing a valve cover and oil separator for a smoking exhaust.

Where to look: Top of the engine: plastic valve cover with the integrated PCV valve

Parts involved: Rocker / valve cover, PCV / oil separator.

Does not apply

The F44 Gran Coupe using the B38 1.5T three-cylinder engine shares the engine mount failure pattern documented in the F20 1 Series. The hydraulic mounts are subject to collapse or fluid weeping, allowing vibration to transmit through the body. The front-wheel-drive F44 platform adds additional complexity — failed engine mounts can also affect front driveshaft alignment and accelerate inner CV joint wear. As the F44 is newer, long-term data is less extensive, but the pattern matches the well-documented F20 failure mode using the same drivetrain.

Where to look: Engine mounts left and right of block, between engine/gearbox unit and front subframe

Parts involved: CV joint and boot.

Does not apply

The G42 2 Series with B58 engine can suffer electric water pump failures leading to overheating. A known BMW weak point where the pump fails without warning and requires prompt replacement.

Where to look: Electric water pump on B58 engine

Parts involved: Water pump.

Does not apply

On the four-cylinder B46/B48 turbo engine in the F22/F23 220i/230i, a thin plastic coolant vent line runs from the cylinder head to the expansion tank. BMW found that its quick-disconnect coupling cannot cope with engine heat over the life of the part and can snap off at the cylinder head, dumping coolant and risking overheating if the car is driven on. BMW issued service action SIB 17 01 21 (revised April 2022) to replace the line on F22, F23, F30, F31, F32, F33, F34 and F36 cars built from 24 April 2015 to 24 September 2019. That bulletin is a BMW North America document, so a NZ or AU car may never have had the new line fitted; the part itself is cheap, the risk is overheating damage if the coupling lets go on the road.

Example of the part — not this vehicle

Where to look: Top of the engine: plastic coolant vent line between the cylinder head and the coolant expansion tank

Parts involved: Cylinder head.

Does not apply

The first-generation B58 feeds boosted air from the turbo to the throttle through an all-plastic factory charge pipe. With age and heat the plastic and its coupler become brittle, and the pipe can crack or pop off under boost, giving a sudden loud whoosh, a big loss of power and limp mode. It is far less common than on the older N55, but the risk climbs steeply on tuned cars running extra boost, and the M240i is a very commonly tuned car. Many owners fit an aluminium aftermarket pipe; on its own that is a sign of modification worth asking about.

Where to look: Front of the engine: plastic charge pipe between the intercooler outlet and the throttle body

Parts involved: Turbocharger.

Does not apply

An internal component in the starter motor fitted to the 2.0-litre four-cylinder 230i wears early. In mild cases the car will not start; in the worst cases the starter draws enough current to overheat and catch fire. BMW recalled it in the United States as campaign 26V-056 and expanded it as 26V-438 in July 2026, covering 230i and 230i xDrive Coupes built between July 2021 and April 2025 — the longest build window of any model in the campaign. The remedy is a redesigned starter fitted free of charge. The six-cylinder M240i is not affected. New Zealand and Australian 230i cars come off the same production lines, so the VIN should be checked against the recall register before you buy.

Where to look: Starter motor low on the gearbox bellhousing at the back of the engine, on the right-hand side; the build-date plate is in the driver's door aperture.

Parts involved: Starter motor.

Does not apply

The F44 Gran Coupe adopts a front-wheel-drive UKL platform layout with transversely mounted engine — a departure from BMW's traditional RWD. The front driveshafts are longer than typical FWD competitors due to packaging constraints, and the inner CV joint boots are subject to splitting from heat and flex stress. Once a CV boot splits, grease is expelled and the joint runs dry, leading to clicking under load and eventually joint failure. NZ road conditions including sharp corners and hilly terrain accelerate wear on the inner joints. As these cars enter their fifth and sixth year, CV boot failure is an expected inspection item.

Example of the part — not this vehicle

Where to look: Front driveshafts, inner CV joints at gearbox end of each driveshaft

Parts involved: CV joint and boot.

Does not apply

The M2 F87 using the S55 engine and the 228i/M235i using the N55 engine are fitted with oil cooler lines (high-pressure hoses and hard pipe sections) that run through the engine bay and are subject to heat cycling. The crimped end-fittings on the rubber sections are known to crack or weep over time, producing oil leaks onto hot exhaust components. On the S55 in particular, the cooler lines route near the turbochargers where temperatures are extreme. Minor seeping is a fire risk if oil contacts exhaust components. Replacement requires aftermarket performance-grade hoses on higher-mileage examples.

Where to look: Oil cooler lines from oil cooler to engine block, routing past turbochargers on S55; front of engine on N55

Parts involved: Turbocharger.

Does not apply

The first-generation B58 3.0 turbo six in the F22/F23 M240i has a plastic oil filter housing that also carries the oil-to-coolant heat exchanger. With heat cycling the gaskets between the housing, the block and the cooler flatten, and the plastic can warp or crack, so the engine weeps oil, coolant or both. Oil runs down the intake side of the engine and a coolant leak into the oil can mix the two fluids, which is the expensive outcome. BMW faces a US class action over this housing on B46, B48 and B58 engines in 2014 to 2021 1, 2, 3 and 4 Series cars; there is no recall or extended warranty in NZ or AU.

Where to look: Left (intake) side of the engine at the front, where the oil filter canister screws in from the top

Parts involved: Turbocharger.