Honda2005–2022 Critical issues documented

Honda Fit Shuttle GP7: common faults & what to check

The GP7 is the Honda Fit Shuttle built 2011–2022. Of the 19 faults documented for the Fit Shuttle, 8 apply to this generation, each with its symptoms, what to inspect and a typical repair cost. Free, no account needed.

Check this exact Honda Fit Shuttle

Odometer history
Money owing
Reported stolen
Ownership history

Official NZ vehicle register data
NZ owned and operated

Type the plate for the free basics. The full record is a paid check from $13.49, one car at a time, no subscription.

No NZ plate yet, or buying in Australia? Pick the generation and engine and start a free check below. New to KickTyres? How the check works →

Documented faults

Critical

Most serious

$380–$1,200

Typical repair

Systems covered

You're looking at the GP7

Everything below is narrowed to this variant. Pick a different one to change it.

2011–2022GP7 Selected2011–2022GP7Engine not documented for this generationEngine not documentedDocumented issues8 knownSee faults & what to checkPhoto: EurovisionNim via Wikimedia Commons, CC BY-SA 4.0.

Choose a different generation

Now narrow it to the engine

A 1.8 and a 2.4 of the same car do not fail the same way, so the faults below narrow to the engine as well as the year. Free, no account needed.

Which engine is in it? These cover every year of this model.

1.3L (L13A)· 1.3 litre 1.5L petrol (L15A)· 1.5 litre petrol

A 2012 Honda Fit Shuttle is the GP7 generation (2011 to 2022).

We cannot narrow the engine list to this year, so every engine this model was sold with is offered.

Start your free check on this Honda Fit Shuttle

No plate needed. You get the risk score, the buyer's checklist and the guided inspection for the exact car you picked above — not the whole nameplate.

Honda Fit Shuttle GP7Engine not picked yet

Pick the engine above first: the Fit Shuttle came with 2, and without it the report has to show all of their faults. Pick the engine

Can't confirm for this car

Honda Fit Shuttle · 2012

Narrowed to the year. No engine is recorded for this vehicle. Pick an engine to see which faults apply.

Tell us the engine, or check the engine code on the car, before relying on this.

No engine is recorded for this vehicle.

matched on year only

What to look out for

The checks worth doing on a Honda Fit Shuttle before you hand over any money. Every documented fault is listed below, each with its own page.

Costly issue
Connect a Honda-compatible scanner and read IMA battery cell voltage spread.
See why
IMA NiMH Traction Battery Cell Degradation
The GP2 Fit Shuttle uses Honda's Integrated Motor Assist (IMA) system with a NiMH traction battery pack. Individual battery cells lose capacity unevenly with age, causing the IMA system to reduce assist capability and eventually display the IMA battery warning light. Severe degradation requires battery replacement or individual cell rebuilding.
What you would notice
- IMA battery warning light illuminated on instrument cluster, often appearing at high mileage
- Reduced fuel economy as combustion engine compensates for reduced electric assist
Typically $1,500–$4,000 to put right.
Costly issue
With vehicle raised, grasp front wheel at 6 and 12 o clock and rock — vertical play indicates bearing wear.
See why
Front Lower Control Arm Ball Joint Wear
Front lower arm ball joints wear causing clunking on rough surfaces. Joint wear is accelerated on vehicles used for frequent short urban trips with high steering lock inputs.
What you would notice
- Clunking from front suspension over bumps and speed humps
- Handling imprecision and vague steering feel when cornering
Typically $350–$700 to put right.
Costly issue
Scan for EPS fault codes.
See why
Electric Power Steering Motor Failure
The Fit Shuttle EPS motor can develop an internal fault or overheat, causing complete loss of power assistance. The failure appears suddenly without warning, leaving only heavy unassisted manual steering.
What you would notice
- Sudden loss of power steering assistance, leaving heavy steering — steering warning light illuminates
- Intermittent heavy steering that resolves when the car is restarted and the EPS module resets
Typically $700–$2,200 to put right.
Costly issue
Test brake pedal firmness — pump the pedal several times with engine off, then hold down and start engine.
See why
Brake Master Cylinder Vacuum Servo Leak
The vacuum brake servo can develop an internal leak, reducing braking effectiveness and requiring greater pedal effort to achieve normal braking force. The servo leak also draws in unmetered air past the intake manifold check valve, causing rough idle.
What you would notice
- Increased brake pedal effort required to achieve normal stopping force compared to when new
- Rough idle caused by air leak past servo check valve disrupting intake manifold vacuum
Typically $450–$1,200 to put right.

See all 8 issues for this oneDocumented for the exact year and engine you picked.

Electrical2

01IMA NiMH Traction Battery Cell Degradation

Connect a Honda-compatible scanner and read IMA battery cell voltage spread.hybrid2011–2015Electrical$1,500–$4,000

CommonElectrical $1,500–$4,000 to fix

The GP2 Fit Shuttle uses Honda's Integrated Motor Assist (IMA) system with a NiMH traction battery pack. Individual battery cells lose capacity unevenly with age, causing the IMA system to reduce assist capability and eventually display the IMA battery warning light. Severe degradation requires battery replacement or individual cell rebuilding.

Symptoms to notice

IMA battery warning light illuminated on instrument cluster, often appearing at high mileage
Reduced fuel economy as combustion engine compensates for reduced electric assist

What to check

Connect a Honda-compatible scanner and read IMA battery cell voltage spread. A spread greater than 0.3V between highest and lowest cells indicates degradation. Note the IMA battery charge indicator on the instrument cluster — rapid charge/discharge cycling indicates failing cells.

Where to look: IMA NiMH battery pack under rear boot floor

Ask the seller

“Has the ima nimh traction battery been inspected or repaired?”

02Electric Power Steering Motor Failure

Scan for EPS fault codes.2011–2015Electrical$700–$2,200

OccasionalElectrical $700–$2,200 to fix

The Fit Shuttle EPS motor can develop an internal fault or overheat, causing complete loss of power assistance. The failure appears suddenly without warning, leaving only heavy unassisted manual steering.

Symptoms to notice

Sudden loss of power steering assistance, leaving heavy steering — steering warning light illuminates
Intermittent heavy steering that resolves when the car is restarted and the EPS module resets

What to check

Scan for EPS fault codes. During test drive, check for consistent power assistance at all speeds and steering angles. Any heavy or notchy steering feel warrants further investigation.

Where to look: EPS motor mounted on steering column or rack

Parts involved: Steering rack.

Ask the seller

“Has the electric power steering motor been inspected or repaired?”

Body, brakes, suspension & interior2

03Brake Master Cylinder Vacuum Servo Leak

Test brake pedal firmness — pump the pedal several times with engine off, then hold down and start engine.2011–2015Brakes$450–$1,200

OccasionalBrakes $450–$1,200 to fix

The vacuum brake servo can develop an internal leak, reducing braking effectiveness and requiring greater pedal effort to achieve normal braking force. The servo leak also draws in unmetered air past the intake manifold check valve, causing rough idle.

Symptoms to notice

Increased brake pedal effort required to achieve normal stopping force compared to when new
Rough idle caused by air leak past servo check valve disrupting intake manifold vacuum

What to check

Test brake pedal firmness — pump the pedal several times with engine off, then hold down and start engine; the pedal should drop slightly as vacuum builds.
If pedal does not drop, servo is not providing vacuum.
Listen for a hissing from the brake servo area at idle.

Where to look: Brake master cylinder and vacuum servo, driver side firewall

Parts involved: Intake manifold.

Ask the seller

“Has the brake master cylinder vacuum been inspected or repaired?”

04Front Lower Control Arm Ball Joint Wear

With vehicle raised, grasp front wheel at 6 and 12 o clock and rock — vertical play indicates bearing wear.2011–2015Suspension$350–$700

CommonSuspension $350–$700 to fix

Front lower arm ball joints wear causing clunking on rough surfaces. Joint wear is accelerated on vehicles used for frequent short urban trips with high steering lock inputs.

Symptoms to notice

Clunking from front suspension over bumps and speed humps
Handling imprecision and vague steering feel when cornering

What to check

With vehicle raised, grasp front wheel at 6 and 12 o clock and rock — vertical play indicates bearing wear. Inspect boot for splitting. If a workshop inspection is possible: Lever the lower arm and check for ball joint movement.

Where to look: Front lower suspension control arms

Parts involved: Ball joint.

Ask the seller

“Has the front lower control arm been inspected or repaired?”

Depends on the exact engine — 4 moreDocumented for a specific engine we could not confirm from what you picked. Check the engine code on the car.

Engine, transmission & cooling1

01CVT shudder and start-clutch wear on the L15 wagon

petrol2011–2022TransmissionCan't confirm for this car$300–$5,000

CommonTransmission $300–$5,000 to fix

Can't confirm for this car

The CVT in the 2011-on Airwave/Shuttle wagon shudders when pulling away from a standstill as the start clutch and the belt lose their grip, and it worsens as the fluid ages. Two things a buyer should know. First, the fluid is not ordinary automatic transmission fluid — these need Honda CVT fluid, and a well-meaning service using generic ATF is a known way to bring the shudder on early. Second, a shudder that a fresh fluid change does not clear usually means the start clutch itself is worn, which is a far bigger job. Nearly all of these cars in New Zealand are Japanese imports with no local service record, so assume the fluid history is unknown unless there is paperwork.

Symptoms to notice

Shudder or judder pulling away from a standstill, felt through the floor
Delay before drive engages, or a thunk selecting reverse
Jerking or refusing to pick up speed in D
Whine that rises steadily with road speed

What to check

Do several stop-start take-offs, not one — pull away gently from rest half a dozen times, including on a slight uphill, and feel through the floor and the seat for a shudder or vibration as it takes up drive. That is the whole test and it takes two minutes. Select reverse from park and feel for a delay or a thunk. On the open road, hold a steady 60-80 km/h and listen for a whine that tracks road speed. Ask the seller when the CVT fluid was last changed and — this is the important part — WHICH fluid was used, because generic ATF instead of Honda CVT fluid brings the shudder on early. Ask for any Japanese service records or the import auction sheet. If a workshop inspection is possible: have the fluid condition and the start-clutch engagement assessed before you commit, since the difference between a fluid change and a start clutch is thousands.

Where to look: Transmission — start clutch and belt inside the CVT unit

Parts involved: Clutch.

Ask the seller

“When was the CVT fluid last changed, and was it genuine Honda CVT fluid?”
“Does it shudder or vibrate when pulling away?”
“Do you have any Japanese service records or the auction sheet?”

Electrical3

01L13A IMA Motor Resolver Sensor Fault

Connect Honda Techstream-compatible scanner and look for IMA motor resolver codes.hybrid2011–2015ElectricalCan't confirm for this car$900–$3,000

OccasionalElectrical $900–$3,000 to fix

Can't confirm for this car

The IMA electric motor resolver sensor tracks motor rotor position for precise torque control. Sensor degradation causes the IMA system to detect position errors, resulting in reduced assist, error codes, and in some cases the IMA system disabling entirely and entering charge-only mode.

Symptoms to notice

IMA warning light with reduced or absent electric motor assist
IMA system entering charge-only mode where the motor never provides drive assistance

What to check

Connect Honda Techstream-compatible scanner and look for IMA motor resolver codes.
Note any IMA system warning patterns — especially reduced assist only in certain conditions.
Ask if the dealer has ever diagnosed IMA motor faults.

Where to look: IMA motor integrated with transaxle

Ask the seller

“Has the l13a ima motor resolver been inspected or repaired?”

02Ignition coil and spark plug failure causing stutter and misfire

petrol2005–2022ElectricalCan't confirm for this car$200–$900

CommonElectrical $200–$900 to fix

Can't confirm for this car

A stutter or hesitation on these cars is most often the ignition coils rather than anything in the gearbox, which matters because the two feel similar from the driver's seat and a misfire is far cheaper to fix than a CVT. Coils sit directly on each plug and fail with age and underbonnet heat rather than mileage — relevant on a Japanese import that may have sat before shipping. Left running on a misfire, unburnt fuel passes into the exhaust and can damage the catalytic converter, which is what turns a modest job into an expensive one. Coils and plugs are commonly replaced as a set on a high-kilometre car.

Symptoms to notice

Stutter, hesitation or juddering under acceleration
Flashing engine warning light — that means an active misfire
Uneven idle, sometimes stalling at a standstill
Worse fuel economy than expected

What to check

Start it cold and let it idle for a minute or two with a hand resting on the centre console — a misfire comes through as a rhythmic shake you can feel as much as hear. On the test drive, accelerate firmly up a hill in a mid gear, because a weak coil shows under load before it shows at idle, and pay attention to whether any hesitation feels like an engine stumble (sharp, rhythmic) or a gearbox shudder (smooth, at low speed only) — telling those apart here is worth real money. Watch the dash: an engine light that FLASHES rather than glowing steadily means it is misfiring right now. Under the bonnet with the engine off, look at the coils on top of the engine for cracked plastic or corroded connectors. Ask when plugs and coils were last done. If a workshop inspection is possible: a scan for misfire counts per cylinder names the exact coil and separates this from the CVT for certain.

Where to look: Top of the engine — one ignition coil per spark plug

Parts involved: Ignition coil.

Ask the seller

“When were the spark plugs and ignition coils last replaced?”
“Has the engine light ever come on, and was it flashing?”
“Does it stutter under acceleration, or only when pulling away?”

0312V auxiliary battery drain causing IMA fault

Check battery manufacture date on the label; replacement every 3–4 years is recommended in NZ conditions.hybrid2011–2015ElectricalCan't confirm for this car$280–$750

CommonElectrical $280–$750 to fix

Can't confirm for this car

The GP2 Fit Shuttle Hybrid uses Honda's first-generation IMA (Integrated Motor Assist) system, which requires a separate 12V lead-acid auxiliary battery to power the hybrid control module, body control module, and ancillary electronics. Unlike full hybrid architectures, the IMA system does not robustly top-charge the 12V battery from the main NiMH high-voltage pack under all operating conditions. Frequent short trips and extended city driving leave the 12V battery in a chronic partial-discharge state. When the auxiliary battery drops below the voltage threshold required to initialise the IMA control module, the system triggers an IMA fault and disables hybrid motor assist, reverting to petrol-only operation. The 12V battery is commonly overlooked during standard hybrid servicing.

Symptoms to notice

IMA warning light illuminated on instrument cluster
Loss of electric motor assist — petrol engine only operation
Difficulty starting or vehicle fails to start
Multiple warning lights appearing simultaneously across systems
Fault codes that clear temporarily but return within days

What to check

Check battery manufacture date on the label; replacement every 3–4 years is recommended in NZ conditions.
Inspect the IMA battery cooling fan inlet located behind the rear seat for blockage with debris.
If a workshop inspection is possible: Load-test the 12V auxiliary battery with a dedicated battery conductance tester — a simple multimeter voltage check is insufficient to detect capacity loss.

Where to look: 12V auxiliary battery in engine bay; IMA high-voltage NiMH pack under rear cargo floor

Parts involved: 12V battery.

Ask the seller

“When was the 12V auxiliary battery last replaced and what brand was fitted?”
“Has the IMA warning light ever appeared during ownership?”
“Has the vehicle had any no-start events or recurring warning lights?”
“Has the hybrid system been serviced by a Honda dealer recently?”

Other Honda Fit Shuttle engines and years11 documented issues that do not apply to the one you picked.

Engine, transmission & cooling5

01L15A Timing Chain Guide Wear at High Mileage

petrol2005–2010EngineDoes not apply$1,200–$3,000

OccasionalEngine $1,200–$3,000 to fix

Does not apply

The L15A 1.5 i-VTEC engine uses a single-row timing chain driving the camshafts, retained and guided by plastic chain guides and a hydraulic tensioner. At high mileages — typically above 150,000 km — the plastic guide rails develop wear grooves and the tensioner loses its ability to maintain correct chain tension, particularly at cold start before oil pressure builds. A worn guide or slack chain risks skipping teeth under heavy load, resulting in catastrophic valve-to-piston contact. Cold-start rattle from the timing chain is the primary diagnostic indicator and warrants immediate investigation.

Symptoms to notice

Metallic rattling or chattering from the front of the engine on cold start, lasting several seconds before quietening as oil pressure rises
Camshaft or crankshaft position sensor correlation fault codes stored in ECU, or rough idle and misfires at high mileage indicating timing chain stretch

What to check

Start the engine from cold and listen immediately for a rattling or chattering noise from the front of the engine that diminishes as oil pressure builds within the first 5 to 10 seconds.
A persisting or recurring rattle indicates tensioner or guide failure.
Scan the ECU for camshaft and crankshaft position correlation fault codes.
Check the engine oil level and condition — dirty or low oil accelerates chain and guide wear.
Review the vehicle service history for oil change intervals; extended intervals are the primary cause of premature timing chain component wear.

Where to look: Front of L15A engine block behind the timing chain cover, accessible after removal of cam cover and front cover

Parts involved: Timing chain.

Ask the seller

“What is the current odometer reading, and is there a documented service history showing regular oil changes?”
“Does the engine make any rattling or ticking noise on cold start that goes away after a few seconds?”

02CVT judder and belt slip under load

Road test from a standstill at light throttle for judder.petrol2005–2010TransmissionDoes not apply$2,000–$5,500

OccasionalTransmission $2,000–$5,500 to fix

Does not apply

The Honda Multimatic CVT in the Airwave GJ develops judder under light-load acceleration from a stop and occasional belt slip under harder acceleration in higher-mileage examples, caused by degraded CVT fluid and steel push-belt wear on the pulleys. CVT fluid change history is the primary differentiator – units with never-changed fluid are at high risk. CVT replacement is expensive; early fluid changes significantly extend service life.

Symptoms to notice

Vibration or judder sensation when pulling away from a stop at gentle throttle
Hesitation or engine flare when accelerating from low speed
Slipping sensation under harder acceleration at low to mid speed
Whining noise from the transmission under acceleration load

What to check

Road test from a standstill at light throttle for judder.
Check CVT fluid colour – should be clear pink, not dark brown.
Verify whether CVT fluid has ever been changed.
Listen for whining or slipping under load.

Where to look: CVT unit located behind the engine in transverse layout

Parts involved: CVT belt and pulleys.

Ask the seller

“Has the CVT fluid ever been changed?”
“Any judder or vibration when pulling away from a stop?”
“Any hesitation, flaring, or slipping when accelerating?”

03CVT Belt Judder Under Light Throttle from Cold Start

Conduct a test drive starting from a fully cold engine and apply light throttle acceleration between 10 and 40 km/h.petrol2015 onwardTransmissionDoes not apply$220–$4,800

CommonTransmission $220–$4,800 to fix

Does not apply

The steel push-belt CVT fitted to petrol GK8 and GK9 Shuttle variants exhibits belt-to-pulley slippage judder when applying light throttle during cold start warm-up. The push-belt loses adequate traction against the drive and driven pulleys until CVT fluid reaches full operating temperature, producing a shudder or vibration transmitted through the floor and seat. Degraded or contaminated CVT fluid from infrequent service intervals significantly worsens the condition. Grey imports frequently arrive with unknown CVT fluid change history, making this fault common on higher-mileage examples.

Symptoms to notice

Shudder or vibration felt through floor and seat during light-throttle take-off
Judder most pronounced within the first five to ten minutes after a cold start
Vibration diminishes or disappears completely once CVT fluid reaches operating temperature
Slipping sensation when accelerating gently at low speed in traffic

What to check

Conduct a test drive starting from a fully cold engine and apply light throttle acceleration between 10 and 40 km/h.
Check CVT fluid condition and colour — dark brown, burnt-smelling fluid indicates overdue service.
Confirm service history showing Honda-specification HMMF CVT fluid use and change intervals.

Where to look: Continuously variable transmission unit, push-belt and pulley assembly

Parts involved: CVT belt and pulleys.

Ask the seller

“When was the CVT fluid last changed and with what specification fluid?”
“Has the vehicle ever exhibited shuddering or vibration during gentle acceleration from cold?”
“Has any transmission warning light or slip indicator appeared?”

04L13A timing chain stretch and tensioner wear

Cold-start the engine and listen for chain rattle from the front.petrol2005–2010EngineDoes not apply$500–$1,000

CommonEngine $500–$1,000 to fix

Does not apply

The L13A 1.3L i-DSI engine in the Airwave GJ suffers timing chain stretch and primary tensioner wear from extended service intervals, a common finding on NZ JDM imports where Japanese maintenance history is opaque. Manifests initially as cold-start rattle progressing to rough idle, misfires, and cam timing deviation if left unaddressed. Age and mileage together accelerate chain elongation.

Symptoms to notice

Metallic rattle from engine on cold start that may persist into warm-up phase
Rough idle or misfire in advanced chain stretch cases
Check engine light with cam position or timing fault codes
Increased fuel consumption as timing deviates from specification

What to check

Cold-start the engine and listen for chain rattle from the front. Check oil change history and current oil condition. Scan for cam position or timing DTCs. Estimate service frequency from the odometer reading and available history.

Where to look: Timing chain and primary tensioner, front of L13A engine

Parts involved: Timing chain.

Ask the seller

“What is the service interval history and oil change frequency?”
“Any rattling from the engine on startup?”
“Has any timing chain work been carried out?”

05L15A VTEC Solenoid O-Ring Oil Leak

With engine cold, inspect the upper rear of the engine around the VTEC solenoid for oil staining or wet residue.petrol2005–2010EngineDoes not apply$120–$320

CommonEngine $120–$320 to fix

Does not apply

The VTEC spool valve (oil control solenoid) on the L15A 1.5 i-VTEC engine is sealed to the cylinder head by two rubber O-rings. These O-rings harden and crack with age and heat cycling, allowing pressurised engine oil to seep out around the solenoid body at the top of the engine. The leak is typically slow but progressive. Oil tracks down the cam cover and can reach the exhaust manifold heat shield, producing a burning oil smell. Left unattended the oil loss contributes to low oil level and accelerates cam follower wear.

Symptoms to notice

Oil seeping or dripping from the VTEC solenoid area at the rear top of the engine, visible as dark staining on the cam cover and cylinder head
Intermittent burning oil smell from the engine bay, particularly after sustained highway driving when oil contacts the exhaust heat shield

What to check

With engine cold, inspect the upper rear of the engine around the VTEC solenoid for oil staining or wet residue.
Wipe the area clean, run the engine to operating temperature, then re-inspect for fresh oil weeping around the solenoid body or the seam where it meets the head.
Check engine oil level on the dipstick.

Where to look: Top of L15A engine, VTEC solenoid mounted on the rear of the cylinder head near the cam cover

Parts involved: Exhaust manifold, Cylinder head, Rocker / valve cover.

Ask the seller

“Has there been any oil leak diagnosis or VTEC solenoid seal work carried out?”
“Do you notice any burning oil smell from the engine after a run?”

Electrical3

01Hybrid Battery Cell Imbalance Causing Assist Failure

Request a hybrid battery diagnostic scan showing individual cell voltages and state-of-charge balance across all modules.hybrid2015 onwardElectricalDoes not apply$1,200–$5,500

CommonElectrical $1,200–$5,500 to fix

Does not apply

Individual lithium-ion cells within the GP7/GP8 hybrid traction battery develop unequal state-of-charge over accumulated mileage. The battery management system progressively restricts motor assist as cell imbalance worsens, ultimately disabling hybrid drive entirely. Cold weather and high mileage accelerate cell degradation. Grey imports commonly arrive with no documented battery health history, making the fault undetectable without diagnostic scanning of individual cell voltages.

Symptoms to notice

Hybrid or IMA system warning light illuminated on dashboard
Reduced or completely absent electric motor assist at low speeds
Vehicle reverts to petrol-only operation unexpectedly
Hybrid battery charge gauge fluctuating erratically or pinned at one extreme
Noticeable and progressive drop in fuel economy

What to check

Request a hybrid battery diagnostic scan showing individual cell voltages and state-of-charge balance across all modules.
Check for stored DTCs P0A7F, P0A80 or similar battery deterioration codes.
Confirm whether any hybrid warning lights have appeared in the vehicle's history.

Where to look: Hybrid traction battery pack beneath rear seat cushion

Ask the seller

“Has the hybrid battery pack ever been replaced or reconditioned?”
“Have any hybrid warning lights appeared during ownership?”
“Can you provide a recent OBD scan showing individual battery cell balance data?”

02Electric Power Steering Rack Seal Failure

Check the instrument cluster for an illuminated EPS warning light.petrol2005–2010ElectricalDoes not apply$750–$2,200

OccasionalElectrical $750–$2,200 to fix

Does not apply

The Airwave GJ1/GJ2 is fitted with an electric power steering (EPS) rack. The inner and outer rack seals and bellows deteriorate with age, allowing water and road contamination to enter the rack tube and attack the internal rack teeth and bearing surfaces. Water ingress also promotes corrosion of the EPS torque sensor and motor connector, leading to intermittent or permanent EPS assist loss. Honda's EPS system on this generation responds to internal faults by illuminating the EPS warning indicator and defaulting to unassisted manual steering.

Symptoms to notice

EPS warning light illuminated on the instrument cluster, often accompanied by sudden increase in steering effort indicating loss of power assist
Notchy, tight, or intermittently heavy steering feel during low-speed manoeuvres, particularly in cold or wet conditions

What to check

Check the instrument cluster for an illuminated EPS warning light.
Scan the EPS ECU for stored fault codes.
With the vehicle on the ground, turn the steering lock to lock slowly and feel for notchiness, tightness, or inconsistent weight.
Inspect the rubber rack bellows (gaiters) at each end of the rack for splitting, cracking, or collapse — split boots allow water ingress.
Inspect EPS motor wiring connector for corrosion.

Where to look: Steering rack assembly mounted behind the front subframe crossmember; EPS motor attached to the rack housing

Parts involved: Steering rack.

Ask the seller

“Has the EPS warning light ever come on, and has any steering system work been done?”
“Does the steering feel consistent, or does it sometimes feel heavier than normal?”

0312V Auxiliary Battery Drain Causing Hybrid System Lockout

Verify battery age and cold cranking amp specification against Honda requirements.hybrid2015 onwardElectricalDoes not apply$180–$580

OccasionalElectrical $180–$580 to fix

Does not apply

The GP7/GP8 hybrid system requires the 12V lead-acid auxiliary battery to power the main hybrid system contactors, body control modules and keyless entry before the high-voltage traction battery can be engaged. When auxiliary battery voltage drops below the control module threshold — from age, parasitic drain or repeated short trips that prevent full recharge — the hybrid management system cannot close the main traction battery relay, leaving the vehicle in a no-start lockout state with multiple simultaneous warning lights. This failure mode is commonly misdiagnosed as main hybrid battery failure and causes significant confusion for owners unfamiliar with dual-battery hybrid architecture.

Symptoms to notice

Vehicle will not start despite main hybrid battery gauge showing charge
Multiple warning lights illuminate simultaneously during startup attempt
Push-button start or keyless entry unresponsive
Hybrid READY indicator fails to appear after start button press

What to check

Verify battery age and cold cranking amp specification against Honda requirements. Perform a parasitic drain test by measuring current draw with ignition off to identify any abnormal standby loads. If a workshop inspection is possible: Measure 12V auxiliary battery voltage with a multimeter — resting voltage should exceed 12.4V and rise above 13.8V when the system is active.

Where to look: 12V auxiliary battery in engine bay

Parts involved: 12V battery.

Ask the seller

“When was the 12V auxiliary battery last replaced?”
“Has the vehicle ever failed to start with multiple warning lights appearing simultaneously?”
“Does the vehicle sit unused for extended periods between drives?”

Body, brakes, suspension & interior3

01Rear Torsion Beam Axle Bush Collapse

Lift and support the rear of the vehicle.petrol2005–2010SuspensionDoes not apply$380–$950

OccasionalSuspension $380–$950 to fix

Does not apply

The GJ-platform Airwave uses a rear torsion beam (twist beam) axle located by large rubber pivot bushes pressed into the subframe and beam ends. These polyurethane/rubber composite bushes deteriorate over time through compression fatigue and ozone cracking, eventually collapsing or delaminating internally. When the bushes collapse the rear beam shifts its rest position, altering toe and camber geometry and producing handling instability. The change in geometry is often gradual and drivers may not notice until a wheel alignment check reveals significant rear toe-out on one or both sides.

Symptoms to notice

Clunking or thudding from the rear axle area when traversing sharp bumps or during hard cornering
Rear end instability or tramping during cornering; rear wheel alignment outside specification on both axes when checked

What to check

Lift and support the rear of the vehicle. Inspect the torsion beam pivot bushes visually for cracking, splitting, or rubber/metal separation. Have a wheel alignment check performed and compare rear toe and camber values against specification; values outside tolerance suggest bush collapse. If a workshop inspection is possible: With a pry bar, lever the beam fore and aft and side to side at each pivot point — a serviceable bush shows minimal movement.

Where to look: Rear torsion beam pivot bush housings on both sides, where the beam attaches to the body floor structure

Ask the seller

“Has the rear suspension been inspected or had any bush replacement?”
“Has a wheel alignment been done recently, and were the rear readings in specification?”

02Front Lower Arm Ball Joint Wear

With the wheel hanging free, grip the tyre at 12 and 6 o'clock and rock firmly — any clunk or visible movement at the ball joint indicates wear.petrol2005–2010SuspensionDoes not apply$280–$750

CommonSuspension $280–$750 to fix

Does not apply

The front lower control arm ball joints on the GJ-platform Airwave are pressed-in units that wear progressively through normal use, particularly in the stop-start urban driving conditions common in Japan and in NZ/AU where most examples have been used post-import. Worn ball joints allow the wheel to rock on the joint, producing clunking under braking or over bumps. Advanced wear allows the steering geometry to shift, accelerating tyre wear. In severe cases ball joint failure causes sudden loss of steering control. Replacement typically requires pressing new joints into the existing arm or replacing the full lower arm assembly.

Symptoms to notice

Clunking or knocking from the front suspension when driving over speed bumps, rough roads, or during braking
Vague or wandering steering feel combined with uneven inner tyre edge wear indicating geometry shift from joint play

What to check

With the wheel hanging free, grip the tyre at 12 and 6 o'clock and rock firmly — any clunk or visible movement at the ball joint indicates wear. Inspect the ball joint rubber dust boot for tearing or grease expulsion, which accelerates joint wear. If a workshop inspection is possible: Lift the front of the vehicle safely. Use a pry bar under the arm at the ball joint to check axial play.

Where to look: Front suspension lower control arm, one ball joint per side connecting arm to steering knuckle

Parts involved: Ball joint.

Ask the seller

“Have the front lower ball joints been inspected or replaced?”
“Does the car clunk over bumps or when braking?”

03Brake Caliper Slide Pin Seizure

Pull each pin out of its bore — it should slide smoothly with light finger pressure.petrol2005–2010BrakesDoes not apply$150–$500

CommonBrakes $150–$500 to fix

Does not apply

The front and rear brake calipers on the GJ Airwave use slide pins (guide pins) to allow the caliper to float and apply even pad pressure across the disc. The slide pin rubber boots deteriorate and admit moisture, corroding the steel pins inside their aluminium caliper brackets. Seized slide pins prevent the caliper from releasing fully after the brake pedal is released, causing the inner or outer pad to remain in contact with the disc. This produces heat, accelerated pad and disc wear on one side, and a pulling sensation under braking. Rear caliper screw-type parking brake mechanisms are also susceptible to internal corrosion on NZ/AU-imported examples.

Symptoms to notice

Vehicle pulling to one side under moderate or heavy braking, with the pull worsening as the caliper heats up from continuous dragging contact
Markedly uneven brake pad wear where one pad on a caliper is significantly thinner than its partner, combined with disc scoring or bluing from heat

What to check

Pull each pin out of its bore — it should slide smoothly with light finger pressure. Corroded pins require significant force or will not move at all. Inspect the slide pin rubber boots for cracking or missing sections. Compare inner and outer brake pad thickness on each caliper; a difference greater than 3 mm indicates a seized pin. Spin each wheel by hand with brakes released and check for dragging resistance. If a workshop inspection is possible: Remove the front and rear wheels and inspect caliper slide pins.

Where to look: Front and rear brake calipers at each wheel, slide pins located in the caliper bracket

Parts involved: Brake disc and pads.

Ask the seller

“When were the brakes last serviced, and were the caliper slide pins cleaned and lubricated?”
“Does the car pull to one side when braking, or do you notice any dragging or heat from the wheels after driving?”

What these repairs cost on other cars

Some of the Honda Fit Shuttle’s documented faults are repairs other models share. Each page lists the documented NZ cost for every model it affects.

Other Honda models

Honda CR-V59 documented faults Honda Accord55 documented faults Honda Jazz51 documented faults Honda Grace18 documented faults Honda Insight16 documented faults Honda CR-Z15 documented faults

Honda Fit Shuttle buyer questions

Is the Honda Fit Shuttle reliable?

Like any used car, it depends on the specific example and its service history. Across the 19 documented faults for the Honda Fit Shuttle, the recurring problem areas are engine, electrical, and transmission. A Honda Fit Shuttle with a full service history and no signs of the issues listed on this page can be a sound buy but each one needs to be checked individually before you commit.

What are the most common problems with a used Honda Fit Shuttle?

We've catalogued 19 known faults for the Honda Fit Shuttle, covering engine, electrical, and transmission. All 19 are written out in full on this page, with the symptoms to notice, what to inspect, and typical repair costs for each. Free to read, no account needed.

How much do repairs cost on a Honda Fit Shuttle?

Most single repairs on the Honda Fit Shuttle fall between $380–$1,200 at NZ independent-workshop rates. Some of the 19 documented faults cost less and a few cost considerably more, and no one car needs them all. Knowing which ones to look for before you view is what lets you negotiate the price down or walk away.

Should I get a pre-purchase inspection on a Honda Fit Shuttle?

Yes. A Honda Fit Shuttle inspection focused on its known weak points is the single best way to avoid an expensive mistake. KickTyres gives you a guided, model-specific inspection plus a market valuation and negotiation figure for $24.90 far less than the cost of missing one of the faults on this page.