Mercedes-Benz Valente: common faults & what to check
Thinking about buying a used Mercedes-Benz Valente (1999–2014) in New Zealand? We've documented 11 known faults for this model spanning engine, fluid leaks, transmission, and cooling. Each researched and verified before it's published. The most serious issues here are rated critical. Two are set out in full below — the rest, with the symptoms, repair costs and checks for each, are free with an account.
11
Documented faults
Critical
Most serious
$600–$2,200
Typical repair
6
Systems covered
Known Mercedes-Benz Valente faults
Every fault below is documented specifically for this model — researched and verified before it’s published.
01OM611 timing chain wear and tensioner failure
CriticalCommonEngine $2,800–$5,500 to fix
The pre-facelift W638 Vito's OM611 2.2 CDI diesel engine is notorious for timing chain stretch and hydraulic tensioner failure. Chain slack causes rattling on cold start and can lead to chain jump and catastrophic valve damage. A known design weakness in the early CDI units with insufficient lubrication to the upper chain guide.
Symptoms to notice
Rattling noise from front of engine on cold start, fading as oil pressure builds
Check engine light with camshaft/crankshaft correlation codes
Rough idle or misfires if chain has jumped a tooth
Engine will not start or starts and immediately stalls if chain has failed
What to check
Cold-start the engine and listen for chain rattle in the first 10 seconds before oil pressure builds. Scan for P0016/P0017 camshaft correlation faults. Ask for service history showing chain replacement. On high-mileage examples over 200,000 km, assume chain is due.
Where to look: Front of engine, behind the timing cover on the passenger side
Ask the seller
“Has the timing chain been replaced, and at what mileage?”
“Does it rattle on cold start?”
“Any history of low oil pressure or extended oil change intervals?”
02M112 Oil Heat Exchanger Seal Failure and Crankshaft Pulley Delamination
MinorOccasionalFluid Leaks $500–$2,000 to fix
The M112 2.4-litre petrol V6 fitted to early W639 Vito models has two well-documented failure points. First, the oil heat exchanger gasket seal fails from thermal degradation, producing persistent oil leaks from the exchanger housing on the side of the engine. Second, the crankshaft pulley harmonic balancer is prone to delamination of its rubber damping layer after approximately 80,000 km, causing the outer pulley ring to separate. Pulley failure produces vibration, accessory belt misalignment, and if allowed to progress, can damage the crankshaft position sensor and ancillary drive components.
Symptoms to notice
Oil leak from side of engine in the vicinity of the oil filter housing or heat exchanger
Vibration or rough running at idle that worsens with engine load
Squealing or misaligned accessory drive belt
Crankshaft position sensor fault codes after pulley delamination
What to check
Inspect the oil heat exchanger housing and gasket face for oil seepage or wet residue. Check the crankshaft pulley for any visible separation of the rubber damping insert between the inner hub and outer ring — a gap or wobble in the outer ring at idle confirms delamination. Check accessory belt alignment and condition.
Where to look: Oil heat exchanger on engine block side; crankshaft pulley at front-bottom of engine
Ask the seller
“Has the oil heat exchanger gasket been replaced?”
“Has the crankshaft pulley harmonic balancer ever been inspected or replaced?”
“Is there any oil leaking from the engine or vibration at idle?”
Fluid LeaksCritical
TransmissionMajor
EngineMajor
EngineMajor
EngineMajor
EngineMajor
CoolingMajor
Body & RustMajor
SuspensionMinor
9 more documented faults on the Mercedes-Benz Valente
Symptoms, what to check, where to look and what to ask the seller — for every fault above. Free with an account, no card needed. One account covers one vehicle, so make it the car you’re actually looking at.
This page covers the model. Enter the plate of the actual car you’re looking at and see its year, engine, safety rating and register flags — free, no account needed.
Like any used car, it depends on the specific example and its service history. Across the 11 documented faults for the Mercedes-Benz Valente, the recurring problem areas are engine, fluid leaks, and transmission. A Mercedes-Benz Valente with a full service history and no signs of the issues listed on this page can be a sound buy but each one needs to be checked individually before you commit.
What are the most common problems with a used Mercedes-Benz Valente?
+
We've catalogued 11 known faults for the Mercedes-Benz Valente, covering engine, fluid leaks, and transmission. Two are written out in full on this page. The rest — with the symptoms to notice, what to inspect, and typical repair costs for each — are free once you create an account.
How much do repairs cost on a Mercedes-Benz Valente?
+
Most single repairs on the Mercedes-Benz Valente fall between $600–$2,200 at NZ independent-workshop rates. Some of the 11 documented faults cost less and a few cost considerably more, and no one car needs them all. Knowing which ones to look for before you view is what lets you negotiate the price down or walk away.
Should I get a pre-purchase inspection on a Mercedes-Benz Valente?
+
Yes. A Mercedes-Benz Valente inspection focused on its known weak points is the single best way to avoid an expensive mistake. KickTyres gives you a guided, model-specific inspection plus a market valuation and negotiation figure for $17.90 far less than the cost of missing one of the faults on this page.