Volkswagen2007–2017 Critical issues documented

Volkswagen Tiguan 5N: common faults & what to check

The 5N is the Volkswagen Tiguan built 2008–2016. It was sold here with the 1.4 TSI, 2.0 TSI, and 2.0 TDI. Of the 20 faults documented for the Tiguan, 15 apply to this generation, each with its symptoms, what to inspect and a typical repair cost. Free, no account needed.

Check this exact Volkswagen Tiguan

Odometer history
Money owing
Reported stolen
Ownership history

Official NZ vehicle register data
NZ owned and operated

Type the plate for the free basics. The full record is a paid check from $13.49, one car at a time, no subscription.

No NZ plate yet, or buying in Australia? Pick the generation and engine and start a free check below. New to KickTyres? How the check works →

Documented faults

Critical

Most serious

$900–$3,500

Typical repair

Systems covered

You're looking at the 5N

3 engine variants are documented for this generation. Pick yours to narrow further, or keep reading for the generation as a whole.

2008–20165N Selected2008–20165N1.4 TSIFuel not statedDocumented issues7 knownSee faults & what to checkPhoto: Vauxford via Wikimedia Commons, CC BY-SA 4.0.

2008–20165N Selected2008–20165N2.0 TSIFuel not statedDocumented issues13 knownSee faults & what to checkPhoto: Vauxford via Wikimedia Commons, CC BY-SA 4.0.

2008–20165N Selected2008–20165N2.0 TDIFuel not statedDocumented issues13 knownSee faults & what to checkPhoto: Vauxford via Wikimedia Commons, CC BY-SA 4.0.

Choose a different generation

Now narrow it to the engine

A 1.8 and a 2.4 of the same car do not fail the same way, so the faults below narrow to the engine as well as the year. Free, no account needed.

Which engine is in it?

1.4 TSI· 1.4 litre 2.0 TSI· 2.0 litre 2.0 TDI· 2.0 litre

A 2008 Volkswagen Tiguan is the 5N generation (2008 to 2016).

Start your free check on this Volkswagen Tiguan

No plate needed. You get the risk score, the buyer's checklist and the guided inspection for the exact car you picked above — not the whole nameplate.

Volkswagen Tiguan 5NEngine not picked yet

Pick the engine above first: the Tiguan came with 3, and without it the report has to show all of their faults. Pick the engine

Can't confirm for this car

Volkswagen Tiguan · 2008

Narrowed to the year. No engine is recorded for this vehicle. Pick an engine to see which faults apply.

Tell us the engine, or check the engine code on the car, before relying on this.

No engine is recorded for this vehicle.

matched on year only

What to look out for

The checks worth doing on a Volkswagen Tiguan before you hand over any money. Every documented fault is listed below, each with its own page.

Serious issue
Inspect the ball joint boot for splits or missing grease.
See why
Front Lower Control Arm Ball Joint Failure
The front lower control arm on the Tiguan 5N uses a pressed-in ball joint that is not separately serviceable - the entire lower arm must be replaced when the ball joint wears. The ball joint boot seal fails first, allowing water and road contamination to accelerate wear of the joint bearing surface. In advanced cases the ball joint can separate from the control arm under load, causing sudden and complete loss of steering and wheel geometry. This is a safety-critical failure. NZ roads and the Tiguan's comparatively low ride height contribute to accelerated lower arm wear in this market.
What you would notice
- Clunking or knocking from the front suspension when traversing speed bumps, potholes, or rough roads
- Vague or wandering steering feel due to lateral play in the worn ball joint
- Vibration through the steering wheel at speed
- Visible split or missing grease from the ball joint rubber boot on inspection
Typically $700–$1,800 to put right.

See all 15 issues for this oneDocumented for the exact year and engine you picked, including 7 rated critical.

Body, brakes, suspension & interior1 critical1

01Front Lower Control Arm Ball Joint Failure

Inspect the ball joint boot for splits or missing grease.2007–2016Suspension$700–$1,800

OccasionalSuspension $700–$1,800 to fix

The front lower control arm on the Tiguan 5N uses a pressed-in ball joint that is not separately serviceable - the entire lower arm must be replaced when the ball joint wears. The ball joint boot seal fails first, allowing water and road contamination to accelerate wear of the joint bearing surface. In advanced cases the ball joint can separate from the control arm under load, causing sudden and complete loss of steering and wheel geometry. This is a safety-critical failure. NZ roads and the Tiguan's comparatively low ride height contribute to accelerated lower arm wear in this market.

Symptoms to notice

Clunking or knocking from the front suspension when traversing speed bumps, potholes, or rough roads
Vague or wandering steering feel due to lateral play in the worn ball joint
Vibration through the steering wheel at speed
Visible split or missing grease from the ball joint rubber boot on inspection

What to check

Inspect the ball joint boot for splits or missing grease. Check for clunking over road imperfections from the front suspension. Also check the rear lower control arm bushings (front-to-rear pivot) which wear similarly. If a workshop inspection is possible: During a safety inspection, place the vehicle on a hoist and grasp the front wheel at 6 and 12 o'clock to check for vertical play in the ball joint (any perceptible movement is a fail).

Where to look: Front lower control arm, inboard pivot to subframe and outboard ball joint to steering knuckle

Parts involved: Ball joint.

Ask the seller

“Has the vehicle had a suspension inspection recently and do the lower control arms have any play?”
“Is there any clunking or knocking from the front suspension over rough roads?”
“Have the lower control arms or ball joints ever been replaced?”

Depends on the exact engine — 14 moreDocumented for a specific engine we could not confirm from what you picked. Check the engine code on the car.

Engine, transmission & cooling14

012.0 TDI Common Rail High-Pressure Fuel Pump (HPFP) Failure and System Contamination

Ask whether the HPFP has ever been replaced and request a full fuel system service history.diesel2007–2012EngineCan't confirm for this car$3,500–$12,000

OccasionalEngine $3,500–$12,000 to fix

Can't confirm for this car

Early 2.0 TDI common rail engines (CR130 and CR140 variants, 2007–2012) are documented to suffer internal HPFP wear that generates aluminium swarf particles which circulate throughout the entire high-pressure fuel system. Once the fuel rail, injectors, and pressure regulator are contaminated with metal debris, the entire high-pressure circuit must be replaced — not just the pump. VW offered goodwill assistance in some markets but issued no formal recall. Using contaminated or low-quality diesel accelerates failure. Total repair bills frequently exceed NZD 8,000–12,000 when all components are replaced.

Symptoms to notice

Rough running, uneven idle, or misfires on a diesel that should be smooth
Hard starting especially when the engine is at operating temperature
Loss of power under load with no obvious boost or EGR fault code
Low fuel rail pressure fault codes (P0087, P0190 series)
Complete stall and no-restart if HPFP fails to deliver pressure

What to check

Ask whether the HPFP has ever been replaced and request a full fuel system service history. At idle, listen for injector rattle or uneven diesel knock that differs between cylinders. During a test drive note any hard starting when hot, power drop under load, or stumbling. If a workshop inspection is possible: Have a diesel specialist perform an injector balance rate test via OBD if the car is being seriously considered.

Where to look: High-pressure fuel pump on top of the engine driven off the camshaft; fuel rail and injectors in the cylinder head

Parts involved: High-pressure fuel pump, Fuel rail.

Ask the seller

“Has the high-pressure fuel pump ever been replaced, and if so why?”
“Has any injector or fuel system work been carried out on this vehicle?”
“Is there any history of hard starting, stalling, or low power complaints?”

021.4 TSI EA111 Timing Chain Tensioner Failure

Cold-start the engine and listen for chain rattle from the front timing cover during the first 5–10 seconds.petrol2007–2015EngineCan't confirm for this car$2,200–$4,500

CommonEngine $2,200–$4,500 to fix

Can't confirm for this car

The 1.4 TSI CAXA engine uses a plastic timing chain tensioner that loses hydraulic pressure at cold start, allowing chain slack. The chain can jump or snap, bending valves and destroying the engine. Documented extensively on VW owner forums and in multiple TSBs. Most failures occur between 80,000–160,000 km and are almost always cold-start events.

Symptoms to notice

Rattling noise from timing cover at cold start, disappearing after warm-up
Check engine light with cam/crank timing codes (P0016, P0017)
Rough idle or misfires after cold start
Engine cuts out suddenly at startup in advanced cases

What to check

Cold-start the engine and listen for chain rattle from the front timing cover during the first 5–10 seconds.
Request full service history to confirm timing chain/tensioner has been replaced.
Pull fault codes for any P001x cam-crank correlation codes.
Check oil level and condition — low or degraded oil accelerates tensioner wear.

Where to look: Front of engine, behind timing cover on the transmission side

Parts involved: Timing chain.

Ask the seller

“Has the timing chain and tensioner ever been replaced?”
“Any history of cold-start rattling or check engine lights?”
“What oil specification and change interval has been used?”

03EA888 Gen1 Timing Chain Tensioner Failure

Listen for metallic rattling from the rear of the engine on cold start that clears within 5-10 seconds.petrol2007–2013EngineCan't confirm for this car$1,800–$4,200Read the full fault: symptoms, where to look, what to ask the seller

041.4 TSI Cam Follower (Rocker Follower) Premature Wear

Ask for documented service records specifically showing cam follower inspection or replacement.petrol2008–2016EngineCan't confirm for this car$150–$3,000Read the full fault: symptoms, where to look, what to ask the seller

05EA888 Water Pump Plastic Impeller Disbonding

Check coolant temperature gauge behaviour on a sustained highway drive above 100 km/h.petrol2007–2016CoolingCan't confirm for this car$700–$1,800

OccasionalCooling $700–$1,800 to fix

Can't confirm for this car

The EA888 engine uses an externally driven water pump with a plastic impeller pressed and bonded onto a metal shaft. Thermal cycling between cold NZ/AU winter starts and operating temperature causes differential expansion between the plastic hub and metal shaft, progressively loosening the interference fit. The impeller eventually spins freely on the shaft, circulating no coolant while the pump shaft and bearing continue to rotate normally. The critical diagnostic trap is that coolant is not lost externally and the pump does not leak or make noise, so the only warning is rising coolant temperature. If the driver fails to notice the temperature gauge climb, head gasket failure or warped cylinder head results within minutes. The failure is statistically concentrated after 100,000 km and is particularly associated with vehicles that have remained on the standard extended service intervals.

Symptoms to notice

Coolant temperature gauge rising higher than normal or into the red zone
Heater output reduced or absent despite engine reaching operating temperature
No external coolant leak or steam present despite overheating
Engine overheating warning light or temperature alarm activating

What to check

Check coolant temperature gauge behaviour on a sustained highway drive above 100 km/h.
Inspect coolant hoses for signs of previous overheating such as deformation or hardening.
Ask for any history of overheating events.
If timing chain is being replaced, request simultaneous water pump replacement as labour overlap makes it cost-effective.
Verify pump is a metal impeller aftermarket unit or genuine VW unit with updated impeller design.

Where to look: Front of engine block, water pump mounted on timing chain cover, driven by auxiliary belt

Parts involved: Water pump.

Ask the seller

“Has the water pump ever been replaced, and if so was a metal impeller unit fitted?”
“Has the coolant temperature gauge ever risen above normal operating range?”
“Has the engine ever overheated or triggered a temperature warning?”

062.0TSI Excessive Oil Consumption (Piston Rings)

Pull the dipstick and check oil level relative to service history — if significantly low with a recent service stamp, investigate consumption rate.petrol2007–2013EngineCan't confirm for this car$2,500–$7,000Read the full fault: symptoms, where to look, what to ask the seller

07EA888 CCZA/CCZB Excessive Oil Consumption

Check oil level and compare to last service record to estimate consumption rate.petrol2007–2016EngineCan't confirm for this car$2,500–$6,500Read the full fault: symptoms, where to look, what to ask the seller

08DQ250 DSG6 Mechatronics & Oil Pump Failure

Scan for DQ250 (02E) fault codes covering speed sensors, solenoid valves, and pressure faults.2007–2016TransmissionCan't confirm for this car$1,500–$4,000

OccasionalTransmission $1,500–$4,000 to fix

Can't confirm for this car

The DQ250 6-speed wet dual-clutch gearbox used in 5N Tiguans (both 2.0TSI and 2.0TDI DSG variants) is susceptible to mechatronics unit degradation and internal oil pump wear. The integrated mechatronic unit controls clutch engagement pressure and gear selection via solenoid valves; when oil is infrequently serviced, varnish deposits clog solenoid passages and valve body bores. Speed sensor failures and oil pressure faults trigger limp mode. While the DQ250 is more robust than the dry-clutch DQ200, neglected service intervals significantly accelerate wear and eventual failure of the mechatronics assembly.

Symptoms to notice

Limp mode activation with warning light on dash
Harsh, clunky gear changes particularly from standstill
Delayed engagement when selecting Drive or Reverse
Shudder or slip under light throttle

What to check

Scan for DQ250 (02E) fault codes covering speed sensors, solenoid valves, and pressure faults.
Check DSG service record — VW specifies fluid and filter change every 60,000 km, many owners skip this.
Test drive including slow-speed crawl and highway upshifts.
Inspect for any oil seepage around the gearbox bellhousing.

Where to look: DQ250 transaxle, underbody centre-left of engine bay

Parts involved: Mechatronic / valve body.

Ask the seller

“Has the DSG fluid and filter been changed at 60,000 km intervals?”
“Has the gearbox ever required any repair or software update?”

Other Volkswagen Tiguan engines and years5 documented issues that do not apply to the one you picked.

Engine, transmission & cooling5

01DQ381 Mechatronics Unit Failure

Test drive at operating temperature and note any hesitation, shudder, or limp-mode activation.2016 onwardTransmissionDoes not apply$3,500–$7,500Read the full fault: symptoms, where to look, what to ask the seller

02EA888 Gen3 High-Pressure Fuel Pump (HPFP) Cam Follower Wear

Connect VCDS and check fuel rail pressure actual vs specified values at idle and under load.petrol2016 onwardEngineDoes not apply$1,200–$3,500

OccasionalEngine $1,200–$3,500 to fix

Does not apply

The high-pressure fuel pump on EA888 Gen3 engines (fitted to AD1 Tiguan from 2016) is driven directly off the intake camshaft via a mechanical follower (bucket tappet). The cam lobe and follower operate under high contact stress and require adequate lubrication. Insufficient oil change frequency, running low on oil, or extended idling causes accelerated wear of the cam follower and corresponding camshaft lobe. As the follower wears, the HPFP loses stroke and fuel rail pressure drops, causing misfires and difficult starting. In severe cases the camshaft lobe is destroyed, requiring camshaft replacement in addition to the pump and follower.

Symptoms to notice

Hard starting, particularly when the engine has been sitting for several hours (fuel rail pressure bleed-down)
Misfires and rough running under load due to insufficient fuel rail pressure
Check engine light with fuel trim and fuel pressure codes (P0087 fuel pressure below specified)
Metallic debris in engine oil visible on dipstick or during oil drain

What to check

Connect VCDS and check fuel rail pressure actual vs specified values at idle and under load. Pull the oil filler cap and inspect the cam follower bucket if visible. Check oil change history rigorously - this failure is strongly correlated with extended oil change intervals. If a workshop inspection is possible: Remove the HPFP and inspect the cam follower for wear pattern - a flat wear spot or loss of surface hardness indicates camshaft lobe contact damage.

Where to look: High-pressure fuel pump on top of cylinder head, driven by intake camshaft

Parts involved: High-pressure fuel pump.

Ask the seller

“What is the oil change interval that has been followed, and what oil specification was used?”
“Has there ever been a fuel pressure fault code or difficult cold-starting?”
“Has the HPFP cam follower ever been inspected or replaced?”

03Turbocharger Electronic Actuator Failure

Connect VCDS and check for turbocharger-related fault codes (P0299 underboost, P0234 overboost, N75 boost pressure regulation codes).petrol2009 onwardEngineDoes not apply$850–$2,400

OccasionalEngine $850–$2,400 to fix

Does not apply

The EA888 turbocharger uses an electronic actuator motor (replacing the earlier pneumatic wastegate) to control boost pressure via variable position feedback. The actuator motor and position sensor are exposed to significant heat cycling from the turbocharger housing. Actuator gear strip, position sensor failure, and actuator motor seizure are all documented failure modes. When the actuator fails, the ECU cannot regulate boost pressure accurately and typically defaults to a low-boost or no-boost limp mode to prevent over-boosting. The actuator can sometimes be replaced independently of the turbocharger, but on some applications requires turbo removal for access.

Symptoms to notice

Significant loss of power and acceleration above 2,500 rpm, engine feeling flat or restricted
Check engine light with P0299 underboost or N75 boost control deviation fault codes
Engine entering limp mode under hard acceleration with boost-related fault active
Audible mechanical clicking or grinding from the turbo actuator during cold start operation

What to check

Connect VCDS and check for turbocharger-related fault codes (P0299 underboost, P0234 overboost, N75 boost pressure regulation codes). Perform actuator position test in VCDS basic settings to verify actuator range of motion. During a test drive, check for power falling off sharply above 2,500 rpm or inability to reach full boost. Inspect actuator connector for corrosion and wiring chafing near the turbo heat shield.

Where to look: Turbocharger actuator mounted on turbo housing, driver-side of engine

Parts involved: Turbocharger.

Ask the seller

“Has the turbocharger or its actuator ever been replaced or repaired?”
“Does the engine feel strong through the entire rev range, or does power drop off at higher revs?”
“Has a boost pressure fault code ever been logged in the engine ECU?”

04Haldex 5th Generation AWD Coupling Pump and Filter Failure

Confirm the vehicle has the Haldex service in its history (Haldex oil + filter change every 40,000 km).petrol2017 onwardTransmissionDoes not apply$900–$2,200

OccasionalTransmission $900–$2,200 to fix

Does not apply

4MOTION-equipped AD Tiguans use the 5th-generation Haldex coupling to drive the rear axle on demand. The Haldex pump and internal filter are maintenance items that VW does not list in the standard service schedule, causing most owners to skip them. A blocked filter starves the pump, which then fails, leaving the vehicle in permanent front-wheel drive with a coupling warning light. Pump replacement is labour-intensive and the part is expensive. Documented widely across VW/Audi AWD platforms.

Symptoms to notice

AWD or 4MOTION warning light on dashboard
Loss of rear-wheel drive engagement in slippery conditions
Whirring or grinding noise from rear differential area under load
DTC codes relating to AWD coupling control

What to check

Confirm the vehicle has the Haldex service in its history (Haldex oil + filter change every 40,000 km).
Listen for rear differential noise during a test drive with sharp low-speed turns.
Check for any AWD-related fault codes.
If service history is incomplete, budget for an immediate Haldex service.

Where to look: Rear axle, Haldex coupling unit integrated into the rear differential housing

Ask the seller

“Has the Haldex coupling oil and filter been serviced?”
“Any AWD or 4MOTION warning lights?”
“Any previous rear differential or AWD system work?”

052.0 TDI DFCA AdBlue Injector Failure and SCR System Fault

Check the dashboard for any active or stored SCR/AdBlue warning lights.diesel2017 onwardEngineDoes not apply$900–$2,000

OccasionalEngine $900–$2,000 to fix

Does not apply

The DFCA 2.0 TDI engine in the AD Tiguan uses a urea (AdBlue) selective catalytic reduction system. The AdBlue injector located in the exhaust stream is prone to crystallisation blockage and premature failure, particularly in Australian conditions. A failed injector triggers engine derate (power limited to ~70%) and, if left unaddressed, DPF issues downstream. Replacement injectors have also been known to fail early. Documented by Australian VW dealerships and independent diesel workshops.

Symptoms to notice

AdBlue/SCR warning light on dashboard
Engine power derate — noticeable performance reduction
White crystalline deposits visible around exhaust area near rear bumper
P20EE, P205B or similar SCR catalyst efficiency fault codes

What to check

Check the dashboard for any active or stored SCR/AdBlue warning lights.
Inspect the AdBlue tank level and top-up history.
Scan for AdBlue-related fault codes.
Ask if the vehicle has had any previous SCR injector work.
Diesel engines covering short trips are at higher risk from crystallisation.

Where to look: Exhaust system, AdBlue injector mounted in the SCR mixer pipe ahead of the rear catalytic converter

Parts involved: Fuel injector.

Ask the seller

“Has the AdBlue injector ever been replaced or cleaned?”
“Any SCR or emissions warning lights?”
“Predominantly short trip or long trip driving history?”

Volkswagen Tiguan faults in detail

Narrowed to the Volkswagen Tiguan · 2008. Each of these has its own page: the symptoms, where to look, what to ask the seller and what the repair costs. Free, no account needed.

1.4 TSI Cam Follower (Rocker Follower) Premature WearCritical · Engine 2.0 TDI / 2.0 BiTDI EGR Cooler Cracking and Coolant LossMajor · Cooling 2.0TSI Excessive Oil Consumption (Piston Rings)Major · Engine 2.0TSI PCV Valve & Oil Separator FailureMajor · Engine DSG DQ250 Clutch Pack Shudder and WearMajor · Transmission DSG DQ250 Mechatronic Unit FailureCritical · Transmission EA888 CCZA/CCZB Excessive Oil ConsumptionMajor · Engine EA888 Gen1 Timing Chain Tensioner FailureCritical · Engine Haldex 4Motion Rear Coupling Oil Pump and Clutch Pack FailureMajor · Transmission TSI Direct Injection Carbon Buildup on Intake ValvesMajor · Engine

What these repairs cost on other cars

Some of the Volkswagen Tiguan’s documented faults are repairs other models share. Each page lists the documented NZ cost for every model it affects.

Other Volkswagen models

Volkswagen Golf49 documented faults Volkswagen Passat26 documented faults Volkswagen Polo22 documented faults Volkswagen Touareg19 documented faults Volkswagen Amarok18 documented faults Volkswagen Transporter18 documented faults

Volkswagen Tiguan buyer questions

Is the Volkswagen Tiguan reliable?

Like any used car, it depends on the specific example and its service history. Across the 20 documented faults for the Volkswagen Tiguan, the recurring problem areas are engine, transmission, and suspension. A Volkswagen Tiguan with a full service history and no signs of the issues listed on this page can be a sound buy but each one needs to be checked individually before you commit.

What are the most common problems with a used Volkswagen Tiguan?

We've catalogued 20 known faults for the Volkswagen Tiguan, covering engine, transmission, and suspension. All 20 are written out in full on this page, with the symptoms to notice, what to inspect, and typical repair costs for each. Free to read, no account needed.

How much do repairs cost on a Volkswagen Tiguan?

Most single repairs on the Volkswagen Tiguan fall between $900–$3,500 at NZ independent-workshop rates. Some of the 20 documented faults cost less and a few cost considerably more, and no one car needs them all. Knowing which ones to look for before you view is what lets you negotiate the price down or walk away.

Should I get a pre-purchase inspection on a Volkswagen Tiguan?

Yes. A Volkswagen Tiguan inspection focused on its known weak points is the single best way to avoid an expensive mistake. KickTyres gives you a guided, model-specific inspection plus a market valuation and negotiation figure for $24.90 far less than the cost of missing one of the faults on this page.

Check this exact Volkswagen Tiguan

You're looking at the 5N

Now narrow it to the engine

Start your free check on this Volkswagen Tiguan

What to look out for

01Front Lower Control Arm Ball Joint Failure

012.0 TDI Common Rail High-Pressure Fuel Pump (HPFP) Failure and System Contamination

021.4 TSI EA111 Timing Chain Tensioner Failure

03EA888 Gen1 Timing Chain Tensioner Failure

041.4 TSI Cam Follower (Rocker Follower) Premature Wear

05EA888 Water Pump Plastic Impeller Disbonding

062.0TSI Excessive Oil Consumption (Piston Rings)

07EA888 CCZA/CCZB Excessive Oil Consumption

08DQ250 DSG6 Mechatronics & Oil Pump Failure

09Haldex 4Motion Rear Coupling Oil Pump and Clutch Pack Failure

102.0 TDI / 2.0 BiTDI EGR Cooler Cracking and Coolant Loss

11TSI Direct Injection Carbon Buildup on Intake Valves

122.0TSI PCV Valve & Oil Separator Failure

13DSG DQ250 Mechatronic Unit Failure

14DSG DQ250 Clutch Pack Shudder and Wear

01DQ381 Mechatronics Unit Failure

02EA888 Gen3 High-Pressure Fuel Pump (HPFP) Cam Follower Wear

03Turbocharger Electronic Actuator Failure

04Haldex 5th Generation AWD Coupling Pump and Filter Failure

052.0 TDI DFCA AdBlue Injector Failure and SCR System Fault

Volkswagen Tiguan faults in detail

What these repairs cost on other cars

Other Volkswagen models

Volkswagen Tiguan buyer questions

Is the Volkswagen Tiguan reliable?

What are the most common problems with a used Volkswagen Tiguan?

How much do repairs cost on a Volkswagen Tiguan?

Should I get a pre-purchase inspection on a Volkswagen Tiguan?