Skip to content
KickTyres
Volvo2008–2021 Critical issues documented

Volvo XC60 P3: common faults & what to check

The P3 is the Volvo XC60 built 2009–2017. It was sold here with the 2.0 turbo petrol, 2.4 diesel, and 3.0 turbo petrol. Of the 20 faults documented for the XC60, 11 apply to this generation, each with its symptoms, what to inspect and a typical repair cost. Free, no account needed.

Check this exact Volvo XC60

  • Odometer history
  • Money owing
  • Reported stolen
  • Ownership history
  • Official NZ vehicle register data
  • NZ owned and operated

Type the plate for the free basics. The full record is a paid check from $13.49, one car at a time, no subscription.

No NZ plate yet, or buying in Australia? Pick the generation and engine and start a free check below. New to KickTyres? How the check works →

20

Documented faults

Critical

Most serious

$650–$2,800

Typical repair

39

Service milestones

You're looking at the P3

3 engine variants are documented for this generation. Pick yours to narrow further, or keep reading for the generation as a whole.

Choose a different generation

Now narrow it to the engine

A 1.8 and a 2.4 of the same car do not fail the same way, so the faults below narrow to the engine as well as the year. Free, no account needed.

A 2009 Volvo XC60 is the P3 generation (2009 to 2017).

Start your free check on this Volvo XC60

No plate needed. You get the risk score, the buyer's checklist and the guided inspection for the exact car you picked above — not the whole nameplate.

Volvo XC60 P3Engine not picked yet

Pick the engine above first: the XC60 came with 3, and without it the report has to show all of their faults. Pick the engine

Free. The paid plate check is separate, and stays optional.

Can't confirm for this car

Volvo XC60 · 2009

Narrowed to the year. No engine is recorded for this vehicle. Pick an engine to see which faults apply.

Tell us the engine, or check the engine code on the car, before relying on this.

  • No engine is recorded for this vehicle.

matched on year only

What to look out for

The checks worth doing on a Volvo XC60 before you hand over any money. Every documented fault is listed below, each with its own page.

  • Serious issue

    Ask the seller or a Volvo dealer whether the 2020 front seat belt cable recall has been done and ask for the record.

    See why

    Front seat belt steel cable can fatigue and break: recall (first generation XC60, 2008-2017)

    On the first generation XC60, the flexible steel cable that anchors the outboard side of each front seat belt can fatigue and separate, so the belt may not hold the occupant in a crash. Volvo recalled about 2.18 million cars worldwide, including 24,977 in Australia (ACCC PRA 2020/18415, REC-001435) and NHTSA 20V378 in the USA. The fix is a free replacement of the seat belt fastener at a Volvo dealer.

    What you would notice

    • Usually none before failure
    • Seat belt buckle side feels loose or the cable is frayed beside the seat

    Typically $0–$400 to put right.

  • Serious issue

    Enter the VIN into the NHTSA recall lookup at nhtsa.gov/recalls and the NZTA recall database before purchase.

    See why

    ARC airbag inflator rupture risk — active safety recall

    Selected XC60 first-generation vehicles were fitted with ARC (ARC Automotive) airbag inflators in driver or passenger positions. ARC inflators are under NHTSA investigation and recall due to a propellant manufacturing defect that can cause the metal inflator housing to rupture explosively upon deployment, creating high-velocity metal fragments directed into the occupant compartment. The mechanism is analogous to the Takata recall but involves a different manufacturer. Recall completion rates for this campaign were documented as low, meaning a significant proportion of vehicles may still carry the defective units.

    What you would notice

    • No symptoms prior to a crash deployment event
    • Recall notification letter may have been issued if vehicle registered with Volvo

    Typically $0–$2,500 to put right.

  • Worth checking

    With the engine idling, turn the wheel lock to lock slowly and feel for tight or notchy spots and listen for pump whine.

    See why

    Power steering fluid leaks and notchy steering rack wear

    First-generation XC60s (which use hydraulic power steering) commonly leak from the power steering hoses, pump and rack seals as they age, and the rack itself is a known weak component on Volvos of this era - wear shows up as notchy or sticky spots as you turn. Left low on fluid, the pump whines and dies and the rack wear accelerates. A hose is cheap; a replacement rack is not. UK MOT-style histories and forums frequently flag PS leaks as advisories on these cars.

    What you would notice

    • Whining or groaning when turning at low speed
    • Notchy or tight spots as the wheel turns
    • Fluid drips under the front of the car
    • Steering heavier than expected at parking speeds

    Typically $250–$2,800 to put right.

Volvo XC60 service schedule

The 2 engines a 2009 Volvo XC60 was sold with, each with its own intervals. Pick your engine above to narrow this to one. These are the model’s intervals — the car’s own service book is the only thing that can tell you what has actually been done to it.

First Generation · 2009–2017 · 2.4L D5 Diesel - AWD

Diesel

Due by distance

  1. 150,000 km

    Have the timing belt and water pump properly checked if there is no paperwork saying it has been done.

  2. 200,000 km

    Inspect the diesel particulate filter, and clean the EGR valve if needed, to keep the engine running efficiently.

  3. 250,000 km

    Check the Haldex coupling fluid so the four-wheel-drive system stays responsive.

First Generation · 2008–2010 · 3.0L T6 Petrol - AWD

Petrol

Due by distance

  1. 100,000 km

    Inspect the auxiliary belts and look for small oil seeps around the valve cover.

  2. 150,000 km

    Service the Haldex all-wheel-drive fluid and filter here before problems start.

  3. 200,000 km

    A full suspension refresh, struts and shock absorbers included, is worth considering to keep the Volvo ride quality.

See all 11 issues for this oneDocumented for the exact year and engine you picked, including 3 rated critical.
Electrical1 critical1

01ARC airbag inflator rupture risk — active safety recall

Enter the VIN into the NHTSA recall lookup at nhtsa.gov/recalls and the NZTA recall database before purchase.2008–2014Electrical
RareElectrical $0–$2,500 to fix

Selected XC60 first-generation vehicles were fitted with ARC (ARC Automotive) airbag inflators in driver or passenger positions. ARC inflators are under NHTSA investigation and recall due to a propellant manufacturing defect that can cause the metal inflator housing to rupture explosively upon deployment, creating high-velocity metal fragments directed into the occupant compartment. The mechanism is analogous to the Takata recall but involves a different manufacturer. Recall completion rates for this campaign were documented as low, meaning a significant proportion of vehicles may still carry the defective units.

Symptoms to notice

  • No symptoms prior to a crash deployment event
  • Recall notification letter may have been issued if vehicle registered with Volvo

What to check

Enter the VIN into the NHTSA recall lookup at nhtsa.gov/recalls and the NZTA recall database before purchase. Contact a Volvo dealer to verify recall completion status for this specific VIN and request written confirmation that the remedy has been applied.

Where to look: Airbag inflator modules in the steering wheel hub and dashboard passenger side

Ask the seller

  • “Has the airbag recall been checked on this VIN?”
  • “Has the recall remedy been completed at a Volvo dealer?”
  • “Can you provide the dealer completion paperwork?”
Body, brakes, suspension & interior1 critical1

02Front seat belt steel cable can fatigue and break: recall (first generation XC60, 2008-2017)

Ask the seller or a Volvo dealer whether the 2020 front seat belt cable recall has been done and ask for the record.2008–2017Interior
OccasionalInterior $0–$400 to fix

On the first generation XC60, the flexible steel cable that anchors the outboard side of each front seat belt can fatigue and separate, so the belt may not hold the occupant in a crash. Volvo recalled about 2.18 million cars worldwide, including 24,977 in Australia (ACCC PRA 2020/18415, REC-001435) and NHTSA 20V378 in the USA. The fix is a free replacement of the seat belt fastener at a Volvo dealer.

Symptoms to notice

  • Usually none before failure
  • Seat belt buckle side feels loose or the cable is frayed beside the seat

What to check

  1. Ask the seller or a Volvo dealer whether the 2020 front seat belt cable recall has been done and ask for the record.
  2. Look at the buckle side of both front seats with a torch for a frayed or kinked cable and pull hard on each latched buckle.
  3. If a workshop inspection is possible: have a Volvo dealer check recall status against the VIN.

Where to look: Front seats, inboard buckle side (seat belt fastener steel cable)

Ask the seller

  • “Has the 2020 seat belt cable recall been done on this car?”
  • “Can you show the dealer record?”
Fluid leaks1

03Power steering fluid leaks and notchy steering rack wear

With the engine idling, turn the wheel lock to lock slowly and feel for tight or notchy spots and listen for pump whine.2009–2017Fluid Leaks
OccasionalFluid Leaks $250–$2,800 to fix

First-generation XC60s (which use hydraulic power steering) commonly leak from the power steering hoses, pump and rack seals as they age, and the rack itself is a known weak component on Volvos of this era - wear shows up as notchy or sticky spots as you turn. Left low on fluid, the pump whines and dies and the rack wear accelerates. A hose is cheap; a replacement rack is not. UK MOT-style histories and forums frequently flag PS leaks as advisories on these cars.

Symptoms to notice

  • Whining or groaning when turning at low speed
  • Notchy or tight spots as the wheel turns
  • Fluid drips under the front of the car
  • Steering heavier than expected at parking speeds

What to check

  1. With the engine idling, turn the wheel lock to lock slowly and feel for tight or notchy spots and listen for pump whine.
  2. Check the power steering reservoir level and look for wet residue on the rack boots and hose unions under the front.
  3. Look under where the car normally parks for drip stains.

Where to look: Steering rack and hoses behind the front subframe; PS reservoir in the engine bay

Parts involved: Steering rack.

Ask the seller

  • “Has the power steering ever needed topping up?”
  • “Have the rack or PS hoses been replaced?”
  • “Any steering advisories at past inspections/WOFs?”
Depends on the exact engine — 8 moreDocumented for a specific engine we could not confirm from what you picked. Check the engine code on the car.
Engine, transmission & cooling7

01B4204T timing belt tensioner spring failure

Demand receipts confirming timing belt, tensioner, idler pulley, and water pump were replaced together as a kit.petrol2008–2017Engine
OccasionalEngine $650–$12,000 to fix

Can't confirm for this car

The B4204T/T2/T3 2.0-litre turbocharged petrol engine uses a rubber timing belt and a spring-loaded tensioner. The tensioner spring fatigues progressively from heat cycling and can lose preload, allowing belt slack. The belt-driven coolant pump can also seize and suddenly drop tensioner pressure. Once the belt skips a tooth on the camshaft sprocket, valve-to-piston contact is almost certain, causing catastrophic internal engine damage. Volvo's published interval of 120,000 km is widely considered too long by independent specialists; many failures occur between 80,000 and 115,000 km.

Symptoms to notice

  • Rattling or flapping noise from front of engine on cold start
  • Check engine light with P0340 or P0345 camshaft position sensor codes
  • Rough idle or random misfires
  • Sudden engine stall without prior warning in catastrophic cases

What to check

Demand receipts confirming timing belt, tensioner, idler pulley, and water pump were replaced together as a kit. If records are absent or the car is over 90,000 km, budget for immediate replacement before purchase. Listen for any rattling from the timing cover on a cold start.

Where to look: Front of engine behind plastic timing cover on the passenger side

Parts involved: Timing belt.

Ask the seller

  • “When was the timing belt last replaced and was the full kit including tensioner and water pump done at the same time?”
  • “Do you have workshop receipts for the timing belt service?”
  • “Has the car ever thrown a camshaft sensor fault code?”

02B6304T T6 engine excessive oil consumption and piston ring wear

Check the oil level and note whether it is below the dipstick maximum despite being recently serviced.petrol2008–2017EngineRead the full fault: symptoms, where to look, what to ask the seller

033.2 B6324S Timing Chain Tensioner Rattle

Start the engine from completely cold and listen immediately for rattling from the front.petrol2008–2017Engine
OccasionalEngine $2,200–$4,500 to fix

Can't confirm for this car

The 3.2L inline-6 B6324S engine in the first-generation XC60 DZ develops timing chain tensioner wear predominantly above 150,000 km. The hydraulic tensioner degrades and loses pressure, particularly at cold start when oil pressure is slow to build. The characteristic rattle or chain slap on startup, clearing within 20-30 seconds, is the primary warning sign. Without timely repair the chain can skip sprocket teeth or snap, resulting in bent valves and major internal engine damage requiring a full engine rebuild.

The front of a dual overhead camshaft engine with the timing cover removed, exposing the timing chain and sprockets.Example of the part — not this vehicle

The front of a twin-cam engine with the timing cover off — chain, sprockets and guides.

Logansenf · CC BY-SA 4.0 · Wikimedia Commons

Symptoms to notice

  • Rattling or chain slap from front of engine at cold start, clearing within 20-30 seconds as oil pressure builds
  • Increased engine noise at higher RPM on worn examples
  • Check Engine light with camshaft timing or crankshaft correlation fault codes
  • Rough idle during the first minute after cold start on worn tensioners

What to check

Start the engine from completely cold and listen immediately for rattling from the front. Noise that clears within 30 seconds as the engine warms is a reliable tensioner warning. Review oil service records — dirty oil or extended intervals significantly accelerate chain and tensioner wear. Any example above 150,000 km without documented timing chain inspection should be assessed by a workshop before purchase. If a workshop inspection is possible: Pull OBD codes and check for P0016-P0019.

Where to look: Front of engine block, timing chain cover and hydraulic chain tensioner

Parts involved: Timing chain.

Ask the seller

  • “Has any rattling from the engine been noticed at cold start?”
  • “Can you show the full service history with oil change intervals?”
  • “Has the timing chain or tensioner been inspected or replaced?”
  • “What is the current odometer reading?”

04D5244 diesel EGR cooler matrix cracking and coolant loss

Check coolant reservoir for oil contamination (brown frothy emulsion).diesel2008–2017Cooling
CommonCooling $1,400–$3,800 to fix

Can't confirm for this car

The D5244T/T3/T4/T5 2.4-litre and 2.0-litre diesel engines recirculate exhaust gas through an aluminium EGR cooler to reduce NOx emissions. The cooler matrix is subject to severe thermal cycling — cycling between near-ambient coolant temperatures and exhaust gas above 400°C — causing internal hairline cracks in the aluminium matrix. Coolant then enters the intake manifold, causing white smoke and progressive coolant loss. If undetected, coolant ingestion into cylinders causes hydrolock, piston ring failure, or cracked cylinder head. The failure rate accelerates on vehicles used primarily for short urban trips.

Symptoms to notice

  • White or grey smoke from exhaust particularly on startup
  • Coolant level dropping with no visible external leak
  • Sweet smell from exhaust
  • Check engine light with EGR-related fault codes
  • Rough running or misfires as coolant enters combustion

What to check

  1. Check coolant reservoir for oil contamination (brown frothy emulsion).
  2. Inspect the EGR cooler connections and intake manifold for coolant residue or white mineral deposits.
  3. Verify coolant level history with the seller.
  4. A combustion gas test (CO2 sniff test) of the coolant reservoir will confirm head or cooler breach.

Where to look: EGR cooler mounted on the left side of the engine block, connected to the intake manifold

Parts involved: EGR valve.

Ask the seller

  • “Has the coolant ever needed topping up between services?”
  • “Has there ever been white smoke from the exhaust?”
  • “Has the EGR cooler or EGR valve been replaced or inspected?”

05D5/2.4D swirl flap linkage failure and EGR/inlet manifold carbon build-up

Get any stored codes scanned before buying - P2015 is the giveaway.diesel2009–2017EngineRead the full fault: symptoms, where to look, what to ask the seller

06D5 diesel DPF blockage from short-trip urban use

Check the oil level on the dipstick — fuel dilution from repeated failed regens raises the oil level above the maximum mark.diesel2008–2017EngineRead the full fault: symptoms, where to look, what to ask the seller

07Geartronic (TF-80SC) harsh shifting and premature wear without fluid services

On the test drive, accelerate gently from a stop and feel every shift up to 5th - they should be almost imperceptible when warm.2009–2017Transmission
OccasionalTransmission $500–$5,500 to fix

Can't confirm for this car

The Aisin TF-80SC 6-speed auto in first-generation XC60s develops jerky low-speed shifts, hesitation, flaring between gears and occasional transmission warnings, particularly on 2009-2014 cars. Volvo called the fluid 'lifetime' but specialists universally recommend changes every 60,000 km or so - neglected boxes wear valve bodies and clutches and a rebuild is a four-figure job. Many complaints are cured with a proper fluid exchange and software update, so service history matters more than mileage here.

Symptoms to notice

  • Jerky or harsh 1-2 and 2-3 shifts
  • Revs flaring between gears like a slipping clutch
  • Hesitation then thump when accelerating from a stop
  • Transmission service message or warning light

What to check

On the test drive, accelerate gently from a stop and feel every shift up to 5th - they should be almost imperceptible when warm. Try a firm overtaking-style kickdown. Ask specifically whether the transmission fluid has ever been changed and at what mileage; no fluid service by 150,000 km is a red flag and a bargaining point.

Where to look: Automatic transmission under the front of the car

Parts involved: Clutch.

Ask the seller

  • “Has the transmission fluid ever been changed, with invoices?”
  • “Any transmission software updates done?”
  • “Does it ever clunk or flare between gears?”
Fluid leaks1

01PTU power transfer unit bearing and output seal failure

Inspect the PTU case on the driver-side of the transaxle for weeping gear oil on the case fins and surrounding subframe.2008–2017Fluid LeaksRead the full fault: symptoms, where to look, what to ask the seller
Other Volvo XC60 engines and years9 documented issues that do not apply to the one you picked.
Engine, transmission & cooling6

01Diesel Particulate Filter (DPF) Blockage — D4204T

Scan the ECU for DPF soot loading percentage — above 80% indicates imminent blockage.diesel2010–2017EngineRead the full fault: symptoms, where to look, what to ask the seller

02EGR Valve Failure and Intake Coking — D4204T Diesel

Scan for EGR fault codes before test drive.diesel2010–2017EngineRead the full fault: symptoms, where to look, what to ask the seller

03Drive-E T6 Supercharger Belt Tensioner Failure

The Drive-E T6 engine combines a low-pressure turbocharger with a belt-driven Roots-type supercharger to deliver broad power across the RPM range.petrol2017 onwardEngine
OccasionalEngine $700–$1,800 to fix

Does not apply

The Drive-E T6 engine combines a low-pressure turbocharger with a belt-driven Roots-type supercharger to deliver broad power across the RPM range. The supercharger drive belt tensioner is a documented weak point: the tensioner spring fatigues or the idler pulley bearing seizes, causing the belt to slip or separate. Loss of supercharger drive eliminates low-to-mid range boost and reduces the car to turbocharger-only performance, with a marked drop in throttle response from low RPM. A failing tensioner bearing typically emits a squeal or chirp before belt separation, and a shed belt can damage adjacent ancillary components.

Symptoms to notice

  • Noticeable loss of low and mid-range acceleration, particularly below 2500 RPM
  • Engine or boost-related warning light on the instrument cluster
  • Squealing or chirping from the front of the engine bay under load or at light throttle
  • Car feels sluggish at low RPM but may improve at higher revs on turbo contribution alone
  • Belt debris visible in the engine bay in cases of catastrophic belt separation

What to check

During a test drive, assess whether strong boost is felt from approximately 1500 RPM — a healthy T6 should pull hard well before the narrower power band of a turbocharger alone. Weak low-RPM performance that improves at higher revs is a red flag. Inspect the supercharger drive belt for glazing, cracking, or fraying. Listen for squealing or chirping under load. If a workshop inspection is possible: Connect an OBD scanner and check for boost pressure or engine performance fault codes.

Where to look: Front of engine, supercharger belt drive assembly and tensioner idler pulley

Parts involved: Timing belt.

Ask the seller

  • “Has the supercharger drive belt or tensioner ever been replaced?”
  • “Has an engine or boost warning light appeared?”
  • “Has any sluggish acceleration or loss of power been noticed?”
  • “Has any squealing or chirping been heard from the engine bay?”

04Oil Separator (PCV) Failure — B4204T / B6304T

Inspect all PCV hoses for cracks and oil weeping at connection points.petrol2010–2017EngineRead the full fault: symptoms, where to look, what to ask the seller

05Engine Mount Failure Causing Vibration (B4204T3 / 2.0T)

With the bonnet open and the engine idling, observe the engine for excessive rocking.petrol2017 onwardEngine
OccasionalEngine $600–$1,400 to fix

Does not apply

The hydraulic engine mounts on second-generation XC60 models with the B4204T3 2.0T Drive-E engine are subject to premature failure, allowing excessive engine movement and transmitting vibration into the cabin at idle and low speeds. The mounts use a fluid-filled hydraulic construction that collapses internally without visible external damage, making them difficult to identify without force testing on a hoist. Documented on Volvo XC60 owner forums and reported by independent workshop technicians across multiple examples in the 60,000–120,000km range.

Symptoms to notice

  • Vibration through the cabin or steering wheel at idle
  • Clunk or thud when engaging Drive from Park
  • Vibration increases when AC compressor engages at idle
  • Engine visible rocking in the bay on revving

What to check

With the bonnet open and the engine idling, observe the engine for excessive rocking. Compare left and right mounts — one side typically fails first. If a workshop inspection is possible: On a hoist, lever the engine against the mounts using a bar and watch for collapse or excessive travel.

Where to look: Left and right engine mounts, between the engine and front subframe

Ask the seller

  • “Have the engine or transmission mounts been inspected or replaced?”
  • “Is there any vibration at idle, especially with the air conditioning on?”
  • “Is there a clunk when selecting drive from park?”

06Aisin TG-81SC 8-speed gearbox harsh shifting and calibration fault

Test drive the vehicle from cold and observe the quality of low-speed upshifts at gentle throttle.petrol2017 onwardTransmission
CommonTransmission $250–$1,200 to fix

Does not apply

The second-generation XC60 Drive-E models use the Aisin Warner TG-81SC 8-speed torque converter automatic gearbox. Early production calibration files cause the transmission control unit to apply clutch packs too aggressively during low-speed upshifts under light to moderate throttle, producing a noticeable jerk or thump. The condition is most pronounced during cold operation and affects the 1-2 and 2-3 shift events most severely. Volvo released TCU software updates addressing the shift quality map. Vehicles that have not had the update still exhibit the harsh shift behaviour, which over time can cause clutch pack surface wear and accelerate the need for a transmission service.

Symptoms to notice

  • Jerky or thudding upshifts particularly during gentle acceleration from low speed
  • Harsh 1-2 upshift from cold start
  • Hesitation followed by a firm jolt during light-throttle cruise upshifts
  • Customer complaint often described as the car lurching during normal driving

What to check

  1. Test drive the vehicle from cold and observe the quality of low-speed upshifts at gentle throttle.
  2. Check transmission fluid service history for any sign of overdue service.
  3. If a workshop inspection is possible: Verify with a Volvo dealer or VIDA scan tool whether the latest TCU calibration has been applied.

Where to look: Transmission control unit and valve body within the Aisin 8-speed automatic gearbox beneath the vehicle

Parts involved: Torque converter, Clutch.

Ask the seller

  • “Has the Volvo dealer applied the latest transmission software update?”
  • “Has the gearbox ever been investigated for harsh or jerky shifting?”
  • “When was the transmission fluid last changed?”
Electrical1

01Sensus infotainment lag, freezes and black screens

Start the car and time how long the screen takes to become responsive - more than ~30 seconds suggests old software.2017–2021Electrical
CommonElectrical $150–$2,000 to fix

Does not apply

Pre-Android XC60s run the Sensus system, which is slow to boot, laggy to touch inputs, and on early software could freeze or go completely black while driving - taking climate controls with it since almost everything lives in the screen. Software updates cured the worst of it, but an un-updated car still misbehaves, and out-of-warranty screen or module replacement is pricey. From 2022 the Google-based system replaced Sensus and is much slicker.

Symptoms to notice

  • Centre screen slow to boot after start
  • Laggy or missed touch inputs
  • Screen freezing or rebooting mid-drive
  • Occasional total black screen including climate controls

What to check

  1. Start the car and time how long the screen takes to become responsive - more than ~30 seconds suggests old software.
  2. Prod through several menus quickly, run nav and audio together, and watch for stutters.
  3. Ask the dealer to confirm the latest Sensus software is installed for the VIN.

Where to look: Centre portrait touchscreen and infotainment module in the dash

Ask the seller

  • “Is the Sensus software on the latest version?”
  • “Has the screen ever frozen or gone black?”
  • “Any infotainment modules replaced?”
Body, brakes, suspension & interior1

01Four-C air suspension compressor failure (blown 40A fuse) - Volvo QB-100 extended warranty

Confirm whether the car has air suspension (ride height settings in the drive-mode menu).2018–2020Suspension
OccasionalSuspension $1,500–$4,500 to fix

Does not apply

XC60s optioned with air suspension suffer compressor failures caused by an internal valve sticking (manufacturing residue), which seizes the compressor and blows its 40A fuse - the car then sags and shows 'suspension service required'. Volvo acknowledged it with Quality Bulletin QB-100 and extended compressor warranty to 7 years/unlimited km from first registration; many NZ cars are now outside that window, and an aftermarket-rate replacement plus any leaking air springs gets expensive. Coil-sprung cars are immune, so first check which suspension the car actually has.

Symptoms to notice

  • Car sitting low or lopsided after parking overnight
  • 'Suspension service required' / 'Active chassis' warning
  • Compressor running loudly or constantly
  • Ride height not adjusting between modes

What to check

Confirm whether the car has air suspension (ride height settings in the drive-mode menu). View the car cold after it has sat overnight and check it sits level. Cycle the ride height and listen to the compressor - it should raise the car within a minute or so without laboured groaning. Ask whether the compressor was replaced under QB-100 and get the invoice.

Where to look: Air compressor under the boot floor area; air springs at each rear (and front on full air cars) corner

Parts involved: Air suspension strut.

Ask the seller

  • “Has the air suspension compressor been replaced (QB-100)?”
  • “Does the car ever sit low after parking?”
  • “Any suspension warning messages?”
Fluid leaks1

01B4204 2.0 engine crankshaft seal oil leak from clogged PCV system

Look under the front of the engine and around the engine-to-gearbox join with a torch for fresh oil wetness, and check the ground where the car parks.2017 onwardFluid Leaks
OccasionalFluid Leaks $900–$2,800 to fix

Does not apply

All second-generation XC60s use the 2.0-litre four (petrol, diesel or T8 hybrid petrol side), and the engine's PCV crankcase breather system clogs over time - typically well past 100,000 km - letting crankcase pressure build until it pushes oil past the front or rear crankshaft seal. What looks like a simple seal leak returns quickly unless the PCV system is cleaned or replaced at the same time, and the front seal job involves timing-drive disassembly so labour is significant. Documented across the SPA-platform XC60/XC90/S90 on owner forums.

Symptoms to notice

  • Oil drips under the engine after parking
  • Oil misting on the underside of the engine and gearbox joint
  • Burning oil smell after a motorway run
  • Oil level dropping between services
  • Whistling from the oil filler cap area (crankcase vacuum/pressure)

What to check

  1. Look under the front of the engine and around the engine-to-gearbox join with a torch for fresh oil wetness, and check the ground where the car parks.
  2. With the engine idling, carefully lift the oil filler cap - strong suction or pressure suggests PCV problems.
  3. Ask if any oil leak repair included PCV service; a seal-only fix tends to fail again.

Where to look: Front (belt end) and rear crankshaft seals, low on the engine; PCV/breather built into the engine

Parts involved: PCV / oil separator.

Ask the seller

  • “Has an oil leak been repaired, and was the PCV system done at the same time?”
  • “Does it lose any oil between services?”
  • “Any oil spots where it parks?”

Volvo XC60 faults in detail

Narrowed to the Volvo XC60 · 2009. Each of these has its own page: the symptoms, where to look, what to ask the seller and what the repair costs. Free, no account needed.

B6304T T6 engine excessive oil consumption and piston ring wearMajor · EngineD5 diesel DPF blockage from short-trip urban useMajor · EngineD5/2.4D swirl flap linkage failure and EGR/inlet manifold carbon build-upMajor · EnginePTU power transfer unit bearing and output seal failureMajor · Fluid Leaks

What these repairs cost on other cars

Some of the Volvo XC60’s documented faults are repairs other models share. Each page lists the documented NZ cost for every model it affects.

Other Volvo models

Volvo XC9027 documented faultsVolvo S6018 documented faultsVolvo XC4016 documented faultsVolvo V6011 documented faultsVolvo XC706 documented faults

Volvo XC60 buyer questions

Is the Volvo XC60 reliable?

Like any used car, it depends on the specific example and its service history. Across the 20 documented faults for the Volvo XC60, the recurring problem areas are engine, electrical, and interior. A Volvo XC60 with a full service history and no signs of the issues listed on this page can be a sound buy but each one needs to be checked individually before you commit.

What are the most common problems with a used Volvo XC60?

We've catalogued 20 known faults for the Volvo XC60, covering engine, electrical, and interior. All 20 are written out in full on this page, with the symptoms to notice, what to inspect, and typical repair costs for each. Free to read, no account needed.

How much do repairs cost on a Volvo XC60?

Most single repairs on the Volvo XC60 fall between $650–$2,800 at NZ independent-workshop rates. Some of the 20 documented faults cost less and a few cost considerably more, and no one car needs them all. Knowing which ones to look for before you view is what lets you negotiate the price down or walk away.

Should I get a pre-purchase inspection on a Volvo XC60?

Yes. A Volvo XC60 inspection focused on its known weak points is the single best way to avoid an expensive mistake. KickTyres gives you a guided, model-specific inspection plus a market valuation and negotiation figure for $24.90 far less than the cost of missing one of the faults on this page.