Skip to content
KickTyres
BMW2000–2025 Critical issues documented

BMW M3 E90: common faults & what to check

The E90 is the BMW M3 built 2007–2014. It was sold here with the 4.0 V8 petrol (S65). Of the 14 faults documented for the M3, 3 apply to this generation, each with its symptoms, what to inspect and a typical repair cost. Free, no account needed.

Check this exact BMW M3

  • Odometer history
  • Money owing
  • Reported stolen
  • Ownership history
  • Official NZ vehicle register data
  • NZ owned and operated

Type the plate for the free basics. The full record is a paid check from $13.49, one car at a time, no subscription.

No NZ plate yet, or buying in Australia? Pick the generation and engine and start a free check below. New to KickTyres? How the check works →

14

Documented faults

Critical

Most serious

$1,800–$5,500

Typical repair

30

Service milestones

You're looking at the E90 · 4.0 V8 petrol (S65)

Everything below is narrowed to this variant. Pick a different one to change it.

Choose a different generation

Now narrow it to the engine

A 1.8 and a 2.4 of the same car do not fail the same way, so the faults below narrow to the engine as well as the year. Free, no account needed.

A 2008 BMW M3 is the E90 generation (2007 to 2014).

Start your free check on this BMW M3

No plate needed. You get the risk score, the buyer's checklist and the guided inspection for the exact car you picked above — not the whole nameplate.

BMW M3 E90

Free. The paid plate check is separate, and stays optional.

Can't confirm for this car

BMW M3 · 2008

Narrowed to the year. No engine is recorded for this vehicle. Pick an engine to see which faults apply.

Tell us the engine, or check the engine code on the car, before relying on this.

  • No engine is recorded for this vehicle.

matched on year only

What to look out for

We have not documented any faults for the exact BMW M3 you picked.

That is a gap in our research, not a clean bill of health — it does not mean this combination is trouble-free, and it is not a reason to skip the checks. Every one of the 14 faults documented across the BMW M3 is still listed further down this page.

Show every year and engine again

BMW M3 service schedule

The 3 engines a 2008 BMW M3 was sold with, each with its own intervals. Pick your engine above to narrow this to one. These are the model’s intervals — the car’s own service book is the only thing that can tell you what has actually been done to it.

E93 M3 Convertible · 2008–2013 · 4.0L S65 V8

Petrol

Due by distance

  1. 60,000 km

    Have a specialist inspect the rod bearings - a known area for proactive maintenance in the S65 engine for long-term reliability.

  2. 80,000 km

    The suspension components, specifically the dampers and bushings, often begin to show their age, affecting the crisp handling the E93 is known for.

  3. 100,000 km

    Cooling system components, including the water pump and thermostat, may benefit from a refresh here to prevent overheating issues.

E90 M3 Sedan · 2007–2011 · 4.0L S65 V8

Petrol

Due by distance

  1. 80,000 km

    Replace the original engine mounts and check the suspension bushings for typical wear.

  2. 100,000 km

    Refresh the throttle body actuators and ensure the cooling system has been overhauled.

  3. 120,000 km

    Evaluate the VANOS system and associated oil pressure components.

E92 M3 Coupe · 2007–2013 · 4.0L S65 V8

Petrol

Due by distance

  1. 60,000 km

    Full fluid refresh including the differential and transmission, to maintain optimal drivetrain health.

  2. 100,000 km

    Suspension components like control arm bushings and dampers often show age-related fatigue here.

  3. 120,000 km

    Evaluate the cooling system's integrity, particularly the radiator and water pump, so the V8 runs at its intended temperature.

See all 3 issues for this oneDocumented for the exact year and engine you picked, including 1 rated critical.
Depends on the exact engine — 3 moreDocumented for a specific engine we could not confirm from what you picked. Check the engine code on the car.
Engine, transmission & cooling3

01S65 V8 connecting rod bearing wear (E90/E92/E93)

The single most valuable thing you can do is ask for the rod bearing paperwork and read it — when the job was done, at what mileage, and by whom.petrol2007–2013EngineRead the full fault: symptoms, where to look, what to ask the seller

02S65 V8 throttle actuator failure and limp mode

The S65 uses two electronically controlled throttle actuators, one per bank, to operate its individual throttle bodies.petrol2007–2013EngineRead the full fault: symptoms, where to look, what to ask the seller

03M-DCT (GS7D36SG) hydraulic pump and mechatronic faults — transmission warning and limp home (E90/E92/E93)

petrol2008–2013Transmission
OccasionalTransmission $2,000–$8,000 to fix

Can't confirm for this car

The 7-speed dual-clutch gearbox offered on the E9x M3 relies on an internal hydraulic pump (including the so-called sucking jet pump) and a mechatronic control unit. With age these develop pressure and control faults: delayed or refused gear engagement, shudder, gears dropping out, and a 'transmission malfunction' warning that puts the car in limp-home mode. Owner forums document cars losing drive entirely when the pump or control side fails. Repairs range from fluid service and solenoid work to pump replacement or a replacement gearbox, so a DCT car with no fluid-service history deserves caution — BMW's original 'lifetime fill' claim does not hold at these ages.

Symptoms to notice

  • Transmission malfunction warning on the dash
  • Delayed or harsh engagement selecting D or R
  • Shudder in slow traffic or on light throttle
  • Gearbox refusing certain gears or dropping to limp home

What to check

  1. Start the car cold and select Drive, then Reverse, feeling how quickly and smoothly each engages — a pause of more than a second or a clunk is a warning sign.
  2. In the test drive include ten minutes of slow, stop-start running and feel for shudder on take-off, then some brisk full-throttle upshifts and downshifts; every shift should be instant and repeatable with no warnings.
  3. Watch the dash for any transmission message, and try both automatic and manual paddle modes.
  4. Ask for receipts showing DCT fluid services and any gearbox repairs.
  5. If a workshop inspection is possible: read the gearbox control unit with a BMW-capable scan tool for stored pressure and clutch fault codes, and check the DCT fluid service record against the pan/filter condition.

Where to look: Dual-clutch gearbox behind the engine — symptoms felt through gear engagement, shift quality and dash warnings

Parts involved: Mechatronic / valve body.

Ask the seller

  • “Has the DCT fluid ever been changed, and when?”
  • “Has the car ever shown a transmission malfunction warning or gone into limp home?”
  • “Have the mechatronic unit, pump or clutches ever been repaired or replaced?”
Other BMW M3 engines and years11 documented issues that do not apply to the one you picked.
Engine, transmission & cooling8

01S55 crank hub slip and jumped valve timing (M3 3.0)

The S55 3.0 twin-turbo six in the F80 M3 holds its timing chain sprocket to the crankshaft hub by friction rather than a key.petrol2014–2020Engine
OccasionalEngine $3,000–$30,000 to fix

Does not apply

The S55 3.0 twin-turbo six in the F80 M3 holds its timing chain sprocket to the crankshaft hub by friction rather than a key. Under heavy load or a hard downshift the hub can rotate, which knocks the valve timing out. Mild cases bring a Drivetrain Malfunction warning; bad cases bend valves and need an engine rebuild. Tuned cars are most at risk, but stock cars have failed too. There is no recall; the fix is an aftermarket pinned or keyed crank hub.

Symptoms to notice

  • Drivetrain Malfunction or engine warning light after hard driving
  • Rough running or misfire after a high-rev downshift
  • Loss of power
  • Engine will not start or runs very badly after a failure

What to check

Ask whether the car is tuned (ECU flash, downpipes, bigger turbos) and whether an upgraded pinned or keyed crank hub has been fitted, and ask for the invoice. Check for aftermarket parts under the bonnet and listen for a smooth idle. On the test drive watch for any Drivetrain Malfunction warning. A tuned car with no crank hub upgrade carries more risk and should be priced to suit. If a workshop inspection is possible: have a BMW specialist read the engine fault memory for camshaft or crankshaft correlation faults.

Where to look: Front of the engine, behind the crankshaft pulley, at the bottom of the timing chain

Parts involved: Timing chain, Turbocharger.

Ask the seller

  • “Has the engine ever been tuned or remapped?”
  • “Has an upgraded pinned or keyed crank hub been fitted, and can I see the invoice?”
  • “Has the car ever shown a Drivetrain Malfunction warning?”
  • “Has the car been used on track?”

02S55 rod and main bearing failure

Check full service history for oil change intervals and specification.petrol2014–2020Engine
OccasionalEngine $12,000–$28,000 to fix

Does not apply

The S55 3.0 twin-turbo straight-six in the F80 M3 has a well-documented rod and main bearing failure pattern at higher mileages and following hard or track use. The bearings run tighter clearances than the standard N55, and degraded oil or extended drain intervals cause accelerated wear. Spun or wiped bearings result in catastrophic engine failure. Hundreds of cases are documented on BMW M specialist forums. ACL and King aftermarket bearings at correct clearance are a widely-used preventive measure, often installed proactively at 50,000 to 80,000 km.

Symptoms to notice

  • Knocking or tapping noise from lower engine under hard acceleration (rod knock)
  • Low oil pressure warning light, particularly under hard cornering or acceleration
  • Sudden loss of power followed by engine seizure in advanced cases
  • Metal particles or shavings visible in oil during a service drain

What to check

  1. Check full service history for oil change intervals and specification.
  2. Intervals beyond 10,000 km or non-LL-01 spec oil significantly increase risk.
  3. Listen for any knocking under hard acceleration.
  4. Ask about track use.
  5. Confirm whether preventive bearing replacement has been performed.
  6. If a workshop inspection is possible: Oil analysis is strongly recommended before purchase.

Where to look: S55 engine lower end, connecting rod and main bearing journals on the crankshaft

Parts involved: Turbocharger.

Ask the seller

  • “What oil change interval and specification has been used throughout ownership?”
  • “Has the car been driven on track or in any performance driving events?”
  • “Have the rod or main bearings been inspected or replaced with aftermarket units?”
  • “Has an oil analysis ever been performed?”

03S58 main bearing failure (early production batch)

Verify the VIN against any BMW service actions or TSBs for S58 bearing specification.petrol2021 onwardEngine
RareEngine $10,000–$25,000 to fix

Does not apply

Early production S58 3.0 twin-turbo engines in the G80 M3 were subject to a BMW TSB addressing main bearing clearance tolerance deviations in engines produced during 2020 to 2022. Affected units can develop premature main bearing wear leading to oil pressure loss and potential engine failure. BMW issued revised bearing specifications and a dealer service action for affected VIN ranges. Verify against BMW dealer records before purchasing any early G80 M3.

Symptoms to notice

  • Low oil pressure warning on cold or hot start
  • Knocking from engine lower end under load or hard acceleration
  • Oil consumption beyond the expected rate
  • Engine failure without audible warning in severe cases

What to check

  1. Verify the VIN against any BMW service actions or TSBs for S58 bearing specification.
  2. Check full service history for oil change intervals and specification used.
  3. Confirm with a BMW dealer whether this specific vehicle falls within the affected production build range and whether the service action has been completed.

Where to look: S58 engine lower end, main bearing journals on the crankshaft

Parts involved: Turbocharger.

Ask the seller

  • “Has the car been checked against BMW TSBs for S58 bearing specification?”
  • “Has any BMW dealer service action been performed on this engine?”
  • “What oil change interval and specification has been followed?”

04S54 connecting rod bearing wear — the fault that decides the price

petrol2000–2006EngineRead the full fault: symptoms, where to look, what to ask the seller

05S55 cooling system — water pump wear and thermostat failure under load

Do the cold checks first, before the engine is started.petrol2014–2020CoolingRead the full fault: symptoms, where to look, what to ask the seller

06S58 oil consumption — and why topping up matters more here

Check the oil level yourself rather than trusting a service sticker — on this engine it is the single most informative thing under the bonnet.petrol2021–2025EngineRead the full fault: symptoms, where to look, what to ask the seller

07S54 VANOS unit wear — rattle, rough idle and lost mid-range

Listen at the top of the engine and drive it through the rev range — this fault shows in both places.petrol2000–2006EngineRead the full fault: symptoms, where to look, what to ask the seller

08S58 intake valve carbon build-up from around 60,000 km

Be there for a cold start and sit with the engine idling, since a carboned engine is at its worst then.petrol2021–2025EngineRead the full fault: symptoms, where to look, what to ask the seller
Body, brakes, suspension & interior3

01Rear subframe mounting point cracking in the boot floor

The evidence is inside the boot and you can see it without any tools.2000–2006Body & RustRead the full fault: symptoms, where to look, what to ask the seller

02Takata driver airbag inflator recall PRA 2018/17191 (F80 M3, 2014-2017)

Some 2014 to 2017 F80 M3 cars (all engines) were built with a Takata driver's airbag whose propellant can absorb moisture over time.2014–2017Interior
OccasionalInterior $0–$1,500 to fix

Does not apply

Some 2014 to 2017 F80 M3 cars (all engines) were built with a Takata driver's airbag whose propellant can absorb moisture over time. In a crash the inflator can over-pressurise and rupture, throwing metal fragments at the driver, which can cause serious injury or death. BMW Australia recalled F Series cars in a staged campaign from December 2018 (PRA 2018/17191) to replace the airbag free of charge, and a separate 2024 recall (REC-006035) covers cars later fitted with a steering wheel that has a Takata inflator. Have the VIN checked to confirm the recall work is done. Not every car is in the recall; a dealer check of the VIN is the only way to know.

Symptoms to notice

  • No visible symptom: the defect only shows when the airbag deploys
  • Airbag warning light on the dash may indicate an airbag module has been disturbed or replaced with a non-genuine part

What to check

  1. Ask the seller for the BMW dealer invoice showing the Takata driver airbag recall (PRA 2018/17191) was done, and ring a BMW dealer with the VIN to confirm there are no open airbag recalls.
  2. Check the airbag warning light comes on at start-up and goes out after a few seconds.
  3. Look at the steering wheel: if it has been swapped for a different style, ask where it came from, because swapped wheels are covered by a separate Takata recall (REC-006035).
  4. If a workshop inspection is possible: have a BMW dealer read the vehicle recall history by VIN and check the airbag module part label against the recall list.

Where to look: Driver airbag in the centre of the steering wheel

Ask the seller

  • “Has the Takata driver airbag recall been done, and do you have the dealer invoice?”
  • “Has the steering wheel ever been replaced or swapped for a different style?”
  • “Has the airbag warning light ever come on?”

03Front lower control arm ball joint premature wear

Any detectable play indicates replacement is needed.petrol2014 onwardSuspension
CommonSuspension $900–$2,200 to fix

Does not apply

The F80 and G80 M3 use a stiffer M-specific front suspension with modified geometry, and the front lower control arm ball joints are documented to wear prematurely compared to non-M models. Higher lateral loads from aggressive driving and the wider M track accelerate ball joint wear. Failed ball joints cause vague steering and in extreme cases sudden loss of directional control. The G80 generation continues to exhibit this pattern.

The front wheel of a car splayed outward with the lower control arm hanging down after a ball joint separation.Example of the part — not this vehicle

A separated lower ball joint: the control arm has dropped and the wheel has splayed out under the guard.

Elfix · CC0 · Wikimedia Commons

Symptoms to notice

  • Clunking noise from front suspension over bumps or during steering inputs
  • Vague or imprecise steering feel
  • Excessive tyre wear on inner or outer edges
  • Wandering or instability at motorway speeds

What to check

Any detectable play indicates replacement is needed. Inspect the rubber boot for cracking or grease loss. Check both sides simultaneously as wear is often bilateral. If a workshop inspection is possible: Lift the vehicle and check front lower ball joints for play by gripping the tyre at 6 and 12 o'clock positions and rocking firmly.

Where to look: Front lower control arm, ball joint at wheel carrier attachment point

Parts involved: Ball joint.

Ask the seller

  • “Have the front control arm ball joints been replaced?”
  • “When were the front suspension components last inspected?”
  • “Has the car experienced any hard kerb strikes or suspension impacts?”

BMW M3 faults in detail

Narrowed to the BMW M3 · 2008. Each of these has its own page: the symptoms, where to look, what to ask the seller and what the repair costs. Free, no account needed.

S65 V8 connecting rod bearing wear (E90/E92/E93)Critical · EngineS65 V8 throttle actuator failure and limp modeMajor · Engine

What these repairs cost on other cars

Some of the BMW M3’s documented faults are repairs other models share. Each page lists the documented NZ cost for every model it affects.

Other BMW models

BMW 3 Series88 documented faultsBMW 5 Series58 documented faultsBMW 1 Series50 documented faultsBMW 7 Series12 documented faultsBMW X411 documented faultsBMW Z410 documented faults

BMW M3 buyer questions

Is the BMW M3 reliable?

Like any used car, it depends on the specific example and its service history. Across the 14 documented faults for the BMW M3, the recurring problem areas are engine, body & rust, and cooling. A BMW M3 with a full service history and no signs of the issues listed on this page can be a sound buy but each one needs to be checked individually before you commit.

What are the most common problems with a used BMW M3?

We've catalogued 14 known faults for the BMW M3, covering engine, body & rust, and cooling. All 14 are written out in full on this page, with the symptoms to notice, what to inspect, and typical repair costs for each. Free to read, no account needed.

How much do repairs cost on a BMW M3?

Most single repairs on the BMW M3 fall between $1,800–$5,500 at NZ independent-workshop rates. Some of the 14 documented faults cost less and a few cost considerably more, and no one car needs them all. Knowing which ones to look for before you view is what lets you negotiate the price down or walk away.

Should I get a pre-purchase inspection on a BMW M3?

Yes. A BMW M3 inspection focused on its known weak points is the single best way to avoid an expensive mistake. KickTyres gives you a guided, model-specific inspection plus a market valuation and negotiation figure for $24.90 far less than the cost of missing one of the faults on this page.