Skip to content
KickTyres
Volkswagen2000–2023 Critical issues documented

Volkswagen Passat B8: common faults & what to check

The B8 is the Volkswagen Passat built 2015–2023. It was sold here with the 1.8 TSI, 2.0 TSI, and 2.0 TDI. Of the 26 faults documented for the Passat, 6 apply to this generation, each with its symptoms, what to inspect and a typical repair cost. Free, no account needed.

Check this exact Volkswagen Passat

  • Odometer history
  • Money owing
  • Reported stolen
  • Ownership history
  • Official NZ vehicle register data
  • NZ owned and operated

Type the plate for the free basics. The full record is a paid check from $13.49, one car at a time, no subscription.

No NZ plate yet, or buying in Australia? Pick the generation and engine and start a free check below. New to KickTyres? How the check works →

26

Documented faults

Critical

Most serious

$800–$3,800

Typical repair

6

Systems covered

You're looking at the B8

3 engine variants are documented for this generation. Pick yours to narrow further, or keep reading for the generation as a whole.

Choose a different generation

Now narrow it to the engine

A 1.8 and a 2.4 of the same car do not fail the same way, so the faults below narrow to the engine as well as the year. Free, no account needed.

A 2016 Volkswagen Passat is the B8 generation (2015 to 2023).

Start your free check on this Volkswagen Passat

No plate needed. You get the risk score, the buyer's checklist and the guided inspection for the exact car you picked above — not the whole nameplate.

Volkswagen Passat B8Engine not picked yet

Pick the engine above first: the Passat came with 3, and without it the report has to show all of their faults. Pick the engine

Free. The paid plate check is separate, and stays optional.

Can't confirm for this car

Volkswagen Passat · 2016

Narrowed to the year. No engine is recorded for this vehicle. Pick an engine to see which faults apply.

Tell us the engine, or check the engine code on the car, before relying on this.

  • No engine is recorded for this vehicle.

matched on year only

What to look out for

The checks worth doing on a Volkswagen Passat before you hand over any money. Every documented fault is listed below, each with its own page.

  • Costly issue

    Repeat at 12 and 6 o'clock positions.

    See why

    B8 Multilink Rear Trailing Arm Bush Failure

    The B8 Passat uses a fully independent multilink rear suspension with pressed-in rubber bushes in the trailing arm and the lower lateral arms. The bushes, particularly the large trailing arm forward mount bush, degrade in the NZ and AU environment due to road salt exposure on coastal routes and the relatively aggressive spring and damper tune on the Passat. Failed bushes allow the rear axle geometry to move under cornering and braking loads, causing progressive rear-end vagueness and a characteristic tramping sensation over mid-corner bumps. Advanced wear causes audible clunking over expansion joints and measurable rear toe change that can only be resolved by bush replacement. Alignment cannot correct the handling deviation once bushes are excessively worn.

    What you would notice

    • Vague or wandering rear-end feel during cornering
    • Rear tramping or hopping sensation over bumps mid-corner
    • Clunking from rear suspension over speed humps or expansion joints
    • Uneven or accelerated rear tyre wear on inner edges
    • Rear toe-out instability detected during wheel alignment check

    Typically $950–$3,200 to put right.

See all 6 issues for this oneDocumented for the exact year and engine you picked, including 1 rated critical.
Body, brakes, suspension & interior1

01B8 Multilink Rear Trailing Arm Bush Failure

Repeat at 12 and 6 o'clock positions.2015 onwardSuspensionRead the full fault: symptoms, where to look, what to ask the seller
Depends on the exact engine — 5 moreDocumented for a specific engine we could not confirm from what you picked. Check the engine code on the car.
Engine, transmission & cooling5

01EA888 Gen3 1.8/2.0 TSI Piston Ring Oil Consumption

Check the engine oil level before and after a test drive.petrol2012 onwardEngineRead the full fault: symptoms, where to look, what to ask the seller

022.0 TDI DFHA DPF Clogging on Urban Routes

Check service history for any DPF-related work or dealer-forced regenerations.diesel2015 onwardEngineRead the full fault: symptoms, where to look, what to ask the seller

03AdBlue / SCR emissions faults on the 2.0 TDI (B8)

Check the dash for AdBlue or emissions warnings and watch a cold start.diesel2015–2023Engine
OccasionalEngine $800–$3,000 to fix

Can't confirm for this car

The B8 Passat 2.0 TDI uses AdBlue (SCR) after-treatment. The dosing pump, injector, level sensor and NOx sensors fail, giving a countdown warning that eventually stops the car restarting, plus limp mode and reduced power. Parts are dealer-priced and diagnosis can be involved. It is the most common warning-light cause on the late diesel Passat and worth checking carefully because a 'no-restart' countdown can strand you.

Symptoms to notice

  • AdBlue warning with a 'no restart in xxx km' countdown
  • Emissions / engine warning light
  • Reduced power / limp mode
  • Fault clears then returns

What to check

  1. Check the dash for AdBlue or emissions warnings and watch a cold start.
  2. Ask for AdBlue top-up and any SCR/NOx sensor history.
  3. Have the car scanned for stored emissions faults before buying.

Where to look: AdBlue tank and filler, dosing pump/injector on the exhaust, NOx sensors in the exhaust

Parts involved: Fuel injector.

Ask the seller

  • “Any AdBlue or NOx sensor faults in its history?”
  • “Are there stored emissions codes now?”
  • “Is the AdBlue system warning-free today?”

04DSG DQ250 Mechatronic Unit Failure

Check for P17BF, P18AC, P189E.2005–2016TransmissionRead the full fault: symptoms, where to look, what to ask the seller

05DQ381 7-Speed DSG Mechatronic Oil Leak

Inspect the underfloor transmission area for fresh transmission fluid residue around the mechatronic connector access point.2015 onwardTransmission
OccasionalTransmission $2,400–$6,200 to fix

Can't confirm for this car

The DQ381 7-speed wet dual-clutch transmission introduced on the B8 Passat has documented mechatronic unit seal failures causing transmission fluid to leak into the electrical harness connector of the mechatronic assembly. Fluid ingress degrades solenoid resistance and contaminates the pressure control circuits, causing erratic clutch pack engagement. The typical presentation is slipping or hesitation under load, particularly when pulling away from a standstill or when the transmission is under torque during overtaking. The mechatronic unit requires removal of the transmission for full replacement. Early production units from 2015-2018 are most affected; VW updated the mechatronic connector seal specification in a running change.

Symptoms to notice

  • Transmission slipping or hesitating when pulling away from a standstill
  • Jerky or unpredictable engagement under heavy throttle
  • Gearbox warning light with mechatronic fault codes stored
  • Transmission fluid smell inside or underneath the vehicle
  • Loss of drive in specific gear ranges

What to check

  1. Inspect the underfloor transmission area for fresh transmission fluid residue around the mechatronic connector access point.
  2. During the test drive, apply strong throttle from a rolling 20 km/h to 80 km/h - any slip or flare indicates clutch or mechatronic pressure issues.
  3. Request OBD fault code scan for DQ381-specific mechatronic pressure adaptation faults.
  4. Check for any transmission service history including fluid change.

Where to look: Transmission underfloor - mechatronic unit on the left side of the DQ381 gearbox housing

Parts involved: Mechatronic / valve body.

Ask the seller

  • “Has the DSG gearbox warning light ever appeared and what was diagnosed?”
  • “When was the DSG transmission fluid last changed?”
  • “Has the vehicle ever shown slipping or jerking under acceleration?”
  • “Has any dealer replaced or resealed the mechatronic unit?”
Other Volkswagen Passat engines and years20 documented issues that do not apply to the one you picked.
Engine, transmission & cooling16

012.0 TDI Timing Belt Failure and Premature Tensioner Wear

Locate the cambelt replacement sticker on the engine strut or inside the engine bay.diesel2005–2015EngineRead the full fault: symptoms, where to look, what to ask the seller

022.0 TDI oil pump / balance-shaft hex-drive failure and DPF issues

Ask whether the oil pump / balance shaft has been upgraded and treat any oil-pressure warning as a walk-away.diesel2006–2014Engine
OccasionalEngine $2,000–$8,000 to fix

Does not apply

The 2.0 TDI B6/B7 Passat carries the notorious balance-shaft oil-pump module whose hex drive can round off, dropping oil pressure and destroying the engine with little warning - documented from around 120,000-150,000 km. These cars also share the EA189 diesel family caught up in the emissions ('dieselgate') fix, after which some owners report more EGR/DPF trouble. Between a possible catastrophic oil-pump failure and the DPF/EGR after-treatment, the diesel Passat rewards a careful history check.

Symptoms to notice

  • Oil-pressure warning light
  • Sudden bottom-end knock or seizure
  • DPF / emissions warning and limp mode
  • Loss of power
  • Metal particles in the oil

What to check

  1. Ask whether the oil pump / balance shaft has been upgraded and treat any oil-pressure warning as a walk-away.
  2. Confirm the emissions ('dieselgate') recall status and ask about any EGR/DPF work since.
  3. Get it fully warm and check for limp mode.
  4. A scan for stored faults is strongly advised.

Where to look: Oil pump / balance-shaft module in the sump; DPF in the exhaust; EGR on the intake

Parts involved: Diesel particulate filter.

Ask the seller

  • “Has the oil pump / balance shaft been upgraded?”
  • “Was the emissions recall done, and any DPF/EGR issues since?”
  • “Has the oil-pressure light ever come on?”

03R36 3.6 VR6 FSI (BWS) Timing Chain Stretch and Guide Wear — Rear-Mounted Chains

petrol2007–2010EngineRead the full fault: symptoms, where to look, what to ask the seller

041.8T oil sludge and ignition coil-pack failure

Pull the dipstick and oil-filler cap and look for thick tar-like sludge or 'mayonnaise' - a huge red flag on this engine.petrol2000–2005Engine
OccasionalEngine $1,500–$6,000 to fix

Does not apply

The B5.5 Passat's 1.8 20-valve turbo is prone to oil 'sludging' - the small oil galleries and turbo feed coke up with baked oil if servicing was ever skipped or the wrong oil used, starving the turbo and bearings. It was a well-known enough problem that VW extended warranties on it when new. Alongside this, the coil packs fail and cause misfires. A sludged 1.8T can need an engine rebuild; a good service history is everything on this engine.

A four-cylinder ignition coil rail removed from an engine, beside a steel rule for scale.Example of the part — not this vehicle

A coil-on-plug ignition rail, removed. One coil per cylinder.

Cschirp · CC BY-SA 3.0 de · Wikimedia Commons

Symptoms to notice

  • Oil-pressure or engine warning light
  • Turbo whine, smoke or lost boost
  • Misfire / juddering (coil packs)
  • Rattly cold start
  • Dark, thick, sludgy oil on the dipstick

What to check

  1. Pull the dipstick and oil-filler cap and look for thick tar-like sludge or 'mayonnaise' - a huge red flag on this engine.
  2. Demand a full service history with frequent oil changes on the correct synthetic oil.
  3. Listen for turbo whine and watch for smoke.
  4. Ask when the coil packs and cam-belt were last done.

Where to look: Engine oil system and turbo (front of engine); coil packs on top of the engine on the spark plugs

Parts involved: Ignition coil.

Ask the seller

  • “How often was the oil changed and with what oil?”
  • “Has the turbo ever been replaced?”
  • “Is there any sludge under the oil cap?”

05EA888 Gen1/2 1.8 and 2.0 TSI timing chain tensioner failure (118TSI and 147TSI, built before May 2012)

Cold-start the engine and listen for chain rattle for at least 30 seconds before it warms.petrol2008–2012EngineRead the full fault: symptoms, where to look, what to ask the seller

062.0 TSI Timing Chain Tensioner Failure (AXX/BWA)

Cold-start the engine and listen immediately for a metallic rattle from the timing cover area (front of engine, passenger side).petrol2005–2010EngineRead the full fault: symptoms, where to look, what to ask the seller

072.0 TDI High-Pressure Fuel Pump Cam Follower Wear

Request the cam follower inspection service history — VW service action 24AK required inspection and replacement at 40,000 km.diesel2005–2014Engine
OccasionalEngine $1,500–$4,500 to fix

Does not apply

The Bosch CP4 and earlier pump-driven high-pressure fuel pumps on 2.0 TDI engines are driven off a lobe on the camshaft via a cam follower (roller or bucket tappet). Under normal wear the follower degrades, and metal debris contaminates the entire high-pressure fuel circuit — injectors, pump, and fuel rail. This is distinct from the cam follower on the BKD/BMN engines which is a known separate issue. Contamination requires complete fuel system replacement and is catastrophically expensive. VW issued a service action requiring inspection and follower replacement at 40,000 km intervals.

Symptoms to notice

  • Hard starting or extended cranking before engine fires
  • Loss of power and black smoke under acceleration
  • Irregular or loud injector noise (ticking) under load
  • Fuel pressure fault codes (P0087 — fuel rail pressure too low)

What to check

  1. Request the cam follower inspection service history — VW service action 24AK required inspection and replacement at 40,000 km.
  2. A worn follower has scoring or a flat spot on its contact face.
  3. Scan for P0087, P0093 fuel pressure faults.
  4. Ask about injector replacement history on high-mileage cars.
  5. If a workshop inspection is possible: Remove the HPFP and inspect the follower via its access port (3-minute job with correct tooling).

Where to look: High-pressure fuel pump driven off inlet camshaft, rear of cylinder head

Parts involved: High-pressure fuel pump.

Ask the seller

  • “Has the cam follower been inspected and replaced as per VW Service Action 24AK?”
  • “Have any injectors or the high-pressure fuel pump been replaced?”
  • “Has the car had any hard-starting, power loss, or fuel pressure warning lights?”

081.4 TSI Timing Chain Tensioner Wear (CBZA/CDAB)

Cold-start and listen at the cam cover area for a rapid ticking that may settle after 30 seconds of running.petrol2010–2014Engine
OccasionalEngine $1,500–$3,800 to fix

Does not apply

The 1.4 TSI engines used in the B7 Passat share a design-sensitive timing chain tensioner that is susceptible to premature wear, particularly on vehicles that run extended oil change intervals or use incorrect oil specification. Unlike the 2.0 TSI, the 1.4 TSI tensioner is a plastic-ratchet type; wear causes chain slap and eventual skip. The cam follower on the CBZA is also prone to accelerated wear transferring metal debris into the oil circuit.

The front of a dual overhead camshaft engine with the timing cover removed, exposing the timing chain and sprockets.Example of the part — not this vehicle

The front of a twin-cam engine with the timing cover off — chain, sprockets and guides.

Logansenf · CC BY-SA 4.0 · Wikimedia Commons

Symptoms to notice

  • Light metallic ticking from the top of the engine, most pronounced on cold start
  • P0016 or P0341 fault codes (camshaft position correlation)
  • Hesitation or stumble under hard acceleration
  • Oil consumption above 0.5 L per 1,000 km

What to check

  1. Cold-start and listen at the cam cover area for a rapid ticking that may settle after 30 seconds of running.
  2. Pull VCDS logs for timing chain adaptation values — values exceeding 5 degrees retard indicate stretch.
  3. Confirm oil service intervals were not extended beyond 15,000 km.
  4. Check for presence of metal swarf in the oil by draining a small sample through a fine filter.

Where to look: Timing chain assembly, front of engine, accessible behind plastic timing cover

Parts involved: Timing chain.

Ask the seller

  • “Has the timing chain or tensioner been replaced or inspected?”
  • “What oil specification and service interval was used throughout ownership?”
  • “Has any check-engine light appeared relating to camshaft or crankshaft timing?”

092.0 TSI Plastic Impeller Water Pump Failure

Check coolant level and condition.petrol2005–2014CoolingRead the full fault: symptoms, where to look, what to ask the seller

102.0 TSI Excessive Oil Consumption (CAWB/AXX/BWA)

Check the engine oil level and ask the seller when the oil was last changed and how many litres were added between changes.petrol2005–2014EngineRead the full fault: symptoms, where to look, what to ask the seller

112.0 TSI/TFSI oil consumption and timing-chain tensioner rattle (EA888)

Ask how much oil it uses between services - a litre every 1,000-2,000 km is a known EA888 problem.petrol2006–2014EngineRead the full fault: symptoms, where to look, what to ask the seller

122.0 TDI DPF Premature Blockage

Connect VCDS and read DPF soot mass (g) and ash content — soot above 45 g indicates blockage.diesel2005–2014Engine
CommonEngine $700–$3,200 to fix

Does not apply

The Diesel Particulate Filter on 2.0 TDI Passat variants becomes blocked prematurely when the vehicle is used predominantly on short urban trips. The DPF requires sustained motorway-speed driving to reach the temperature needed for passive regeneration. Forced active regeneration injects additional fuel to raise exhaust temperature, but if this cycle fails repeatedly — due to EGR faults, short trips, low oil level, or oil that has absorbed too much diesel — the DPF reaches its service soot limit and must be professionally cleaned or replaced.

Symptoms to notice

  • DPF warning light on dashboard, sometimes accompanied by reduced power mode
  • Excessive fuel consumption as active regeneration cycles increase
  • Engine oil level rising above maximum on dipstick (diesel dilution from failed regeneration)
  • Strong diesel smell from exhaust during active regeneration attempts

What to check

  1. Connect VCDS and read DPF soot mass (g) and ash content — soot above 45 g indicates blockage.
  2. Check oil level: if above maximum, the engine oil has been diluted with diesel from failed regeneration.
  3. Ask about driving patterns — predominantly urban trips below 20 km are a major risk factor.
  4. Confirm DPF service history including forced regenerations or professional cleaning.

Where to look: Exhaust system, downstream of turbocharger and catalytic converter, beneath the car

Parts involved: Diesel particulate filter.

Ask the seller

  • “Has a DPF warning light ever appeared, and how was it resolved?”
  • “Was the car used predominantly for short urban trips under 20 km?”
  • “Has the DPF been professionally cleaned or replaced?”

13Haldex 4Motion Coupling Pump and Clutch Failure

Locate the Haldex unit on the rear differential (mounted between rear driveshafts).2005–2014Transmission
OccasionalTransmission $800–$3,000 to fix

Does not apply

The Haldex Generation 4 all-wheel-drive coupling used in 4Motion Passat variants relies on a pre-charging pump to pre-fill clutch plates before torque demand. The pump is driven by an electric motor and relies on clean Haldex-specific oil changed every 30,000–40,000 km. Neglected oil service causes the pump to seize, blocking instant torque transfer to the rear axle. The clutch plates then run dry and wear rapidly. A failed Haldex unit delivers no torque to the rear wheels and the car behaves as a front-wheel-drive vehicle. Full unit replacement is the typical outcome.

Symptoms to notice

  • Loss of traction on slippery surfaces that 4WD should manage — rear axle not engaging
  • Haldex or 4WD warning light on dashboard
  • Whining or grinding noise from rear differential area under load
  • Burning smell from rear of vehicle during AWD-demanded manoeuvres

What to check

Locate the Haldex unit on the rear differential (mounted between rear driveshafts). Check for Haldex oil service sticker or records — oil and filter must be changed every 30,000–40,000 km with VW G 052 175 A2 fluid. On a test drive on gravel or slippery surface, confirm rear axle engagement under light wheelspin. Connect VCDS to check Haldex controller for faults. If a workshop inspection is possible: Lift the vehicle and inspect for oil leaks at the Haldex unit.

Where to look: Rear axle Haldex coupling unit, mounted between rear driveshafts on rear subframe

Parts involved: Clutch.

Ask the seller

  • “Has the Haldex oil and filter been replaced at or before 40,000 km intervals?”
  • “Has the 4WD system warning light appeared, or has the rear axle appeared not to engage on slippery surfaces?”
  • “Has the Haldex unit been replaced or overhauled?”

142.0 TDI EGR Valve and Cooler Failure

Scan for EGR-related fault codes (P0400, P0401, P040A, P0489).diesel2005–2014EngineRead the full fault: symptoms, where to look, what to ask the seller

15R36 3.6 VR6 FSI (BWS) Intake Valve Carbon Buildup — Direct Injection

petrol2007–2010EngineRead the full fault: symptoms, where to look, what to ask the seller

162.0 TSI Intake Valve Carbon Deposit Buildup

Ask when the intake valves were last cleaned.petrol2005–2014EngineRead the full fault: symptoms, where to look, what to ask the seller
Electrical2

01Starter motor relay spring recall, starter can stay powered and overheat (Passat, 2011-2012 model years)

Ask for Volkswagen paperwork showing the starter relay recall (PRA 2018/16669) was done, or have a dealer check the VIN.2011–2012Electrical
RareElectrical $0–$500 to fix

Does not apply

2011 and 2012 model year Passats (all engines) were recalled in Australia because a bent or broken spring can jam the starter motor relay, so the starter stays powered after the engine starts and can overheat, scorch nearby parts or catch fire (PRA 2018/16669). The relay check or replacement is free at a Volkswagen dealer.

Symptoms to notice

  • Starter keeps whirring or grinding after the engine has started
  • Burning smell from the engine bay or under the dash after starting
  • Flat battery after a short drive

What to check

  1. Ask for Volkswagen paperwork showing the starter relay recall (PRA 2018/16669) was done, or have a dealer check the VIN.
  2. Start the car several times and listen: the starter should stop the moment the engine fires, with no grinding or whine afterwards and no burning smell.
  3. If a workshop inspection is possible: have the starter relay inspected or replaced to the recall standard.

Where to look: Starter motor relay in the fuse and relay carrier

Parts involved: Starter motor.

Ask the seller

  • “Has the starter relay recall been done?”
  • “Has the starter ever kept running after the engine started?”

02Instrument-cluster pixel loss and gauge faults

Sit in the car with the ignition on and read the whole cluster display carefully for missing or garbled pixels.2000–2005Electrical
CommonElectrical $300–$900 to fix

Does not apply

The B5.5 Passat's instrument cluster suffers the classic VW dead-pixel problem: the central display fades or shows scrambled/missing segments, and the fuel and temperature gauges can read erratically or stick. It is an age-related failure of the cluster itself. While you can still drive, a failing cluster can hide a genuine overheat or low-fuel situation, and a replacement or specialist repair is needed. It is one of the most predictable faults on these cars.

Symptoms to notice

  • Missing or scrambled pixels in the dash display
  • Fuel or temperature gauge reading wrongly or sticking
  • Dim or flickering cluster display
  • Warning symbols hard to read

What to check

Sit in the car with the ignition on and read the whole cluster display carefully for missing or garbled pixels. Watch the fuel and temperature needles settle after start-up and check they move sensibly on the drive. A scrambled display is obvious once you look.

Where to look: Instrument cluster behind the steering wheel

Ask the seller

  • “Do all the gauges and the display work fully?”
  • “Has the cluster ever been repaired or replaced?”
  • “Does the temperature gauge read normally?”
Body, brakes, suspension & interior2

01Takata driver airbag inflator recall (late B6 and B7 Passat, 2009-2015)

Ask for Volkswagen paperwork showing the Takata driver airbag was replaced, or have a Volkswagen dealer check the VIN for open recalls before you buy.2009–2015Interior
CommonInterior $0 to fix

Does not apply

Late B6 and B7 Volkswagen Passats (all engines) sold from 2009 to 2015 were recalled in Australia because the Takata driver airbag propellant can absorb moisture with age, and the inflator can then rupture in a crash and throw metal fragments at the driver (PRA 2018/17197, PRA 2019/17582 and PRA 2019/17348). The airbag replacement is free at a Volkswagen dealer. An unrepaired Takata airbag can injure or kill in an otherwise survivable crash.

Symptoms to notice

  • No symptoms: the fault only shows when the airbag deploys

What to check

  1. Ask for Volkswagen paperwork showing the Takata driver airbag was replaced, or have a Volkswagen dealer check the VIN for open recalls before you buy.
  2. Look for a recall completion sticker in the door jamb or service book.
  3. If a workshop inspection is possible: have the dealer confirm the part number of the fitted driver airbag module.

Where to look: Driver airbag in the steering wheel centre

Ask the seller

  • “Has the Takata driver airbag been replaced under recall, and do you have the invoice?”
  • “Has a Volkswagen dealer confirmed no open recalls on this VIN?”

02Front multi-link control-arm and bush wear

On the test drive listen for front-end clonks over rough road and note any wandering steering.2000–2005SuspensionRead the full fault: symptoms, where to look, what to ask the seller

Volkswagen Passat faults in detail

Narrowed to the Volkswagen Passat · 2016. Each of these has its own page: the symptoms, where to look, what to ask the seller and what the repair costs. Free, no account needed.

2.0 TDI DFHA DPF Clogging on Urban RoutesMajor · EngineB8 Multilink Rear Trailing Arm Bush FailureMajor · SuspensionDSG DQ250 Mechatronic Unit FailureCritical · TransmissionEA888 Gen3 1.8/2.0 TSI Piston Ring Oil ConsumptionMajor · Engine

What these repairs cost on other cars

Some of the Volkswagen Passat’s documented faults are repairs other models share. Each page lists the documented NZ cost for every model it affects.

Other Volkswagen models

Volkswagen Golf49 documented faultsVolkswagen Polo22 documented faultsVolkswagen Tiguan20 documented faultsVolkswagen Touareg19 documented faultsVolkswagen Amarok18 documented faultsVolkswagen Transporter18 documented faults

Volkswagen Passat buyer questions

Is the Volkswagen Passat reliable?

Like any used car, it depends on the specific example and its service history. Across the 26 documented faults for the Volkswagen Passat, the recurring problem areas are engine, transmission, and cooling. A Volkswagen Passat with a full service history and no signs of the issues listed on this page can be a sound buy but each one needs to be checked individually before you commit.

What are the most common problems with a used Volkswagen Passat?

We've catalogued 26 known faults for the Volkswagen Passat, covering engine, transmission, and cooling. All 26 are written out in full on this page, with the symptoms to notice, what to inspect, and typical repair costs for each. Free to read, no account needed.

How much do repairs cost on a Volkswagen Passat?

Most single repairs on the Volkswagen Passat fall between $800–$3,800 at NZ independent-workshop rates. Some of the 26 documented faults cost less and a few cost considerably more, and no one car needs them all. Knowing which ones to look for before you view is what lets you negotiate the price down or walk away.

Should I get a pre-purchase inspection on a Volkswagen Passat?

Yes. A Volkswagen Passat inspection focused on its known weak points is the single best way to avoid an expensive mistake. KickTyres gives you a guided, model-specific inspection plus a market valuation and negotiation figure for $24.90 far less than the cost of missing one of the faults on this page.