Audi1996–2022 Critical issues documented

Audi S3 8V: common faults & what to check

The 8V is the Audi S3 built 2012–2020. Of the 18 faults documented for the S3, 3 apply to this generation, each with its symptoms, what to inspect and a typical repair cost. Free, no account needed.

Check this exact Audi S3

Odometer history
Money owing
Reported stolen
Ownership history

Official NZ vehicle register data
NZ owned and operated

Type the plate for the free basics. The full record is a paid check from $13.49, one car at a time, no subscription.

No NZ plate yet, or buying in Australia? Pick the generation and engine and start a free check below. New to KickTyres? How the check works →

Documented faults

Critical

Most serious

$500–$1,900

Typical repair

Service milestones

You're looking at the 8V

Everything below is narrowed to this variant. Pick a different one to change it.

Audi S3, 8V (2012–2020) (KickTyres illustration)

2012–20208V Selected2012–20208VEngine not documented for this generationEngine not documentedDocumented issues3 knownSee faults & what to checkKickTyres illustration, not a photograph.

Choose a different generation

Now narrow it to the engine

A 1.8 and a 2.4 of the same car do not fail the same way, so the faults below narrow to the engine as well as the year. Free, no account needed.

Which engine is in it? These cover every year of this model.

2.0L TFSI· 2.0 litre

A 2014 Audi S3 is the 8V generation (2012 to 2020).

We cannot narrow the engine list to this year, so every engine this model was sold with is offered.

Start your free check on this Audi S3

No plate needed. You get the risk score, the buyer's checklist and the guided inspection for the exact car you picked above — not the whole nameplate.

Audi S3 8V

Likely — same engine family

Audi S3 · 2014

Narrowed by capacity and fuel. No engine code is recorded for this option, so a fault specific to one engine of that size cannot be confirmed from it.

Matched on capacity and fuel, not on an engine code.

matched on 2.0L engine

What to look out for

The checks worth doing on a Audi S3 before you hand over any money. Every documented fault is listed below, each with its own page.

Serious issue
Arrange a cold-start inspection.
See why
2.0 TFSI (CJXC/IS38) Timing Chain Tensioner Wear
The EA888 Gen 3 2.0 TFSI engine fitted to the 8V S3 (CJXC engine code) shares the timing chain tensioner weakness documented across the broader EA888 family. The tensioner's oil feed circuit has marginal oil pressure at cold startup, allowing the chain to slacken momentarily. Over time the chain guide rails wear, and the chain can stretch beyond the tensioner's adjustment range. VW/Audi has issued updated tensioner and guide rail components. The IS38 turbocharger specification in the S3 increases combustion loads, which may marginally accelerate chain wear versus the standard A3 application.
What you would notice
- Brief rattling from the top of the engine on cold startup lasting 3-10 seconds
- P0016/P0017 camshaft/crankshaft correlation fault codes
- Rough running and reduced power after cold start
- Catastrophic failure results in engine stoppage without warning
Typically $2,000–$5,500 to put right.
Costly issue
Check the Haldex service stamp in the service book — it should be listed separately from the main gearbox oil change.
See why
Haldex Rear Differential Clutch Failure Due to Neglected Service
The quattro system on both 8P and 8V S3 models uses a Haldex multi-plate clutch coupling at the rear axle to apportion torque to the rear wheels on demand. The Haldex unit requires its own oil change every 20,000-30,000 km, separate from the main gearbox. This service is frequently overlooked by non-specialist garages. Neglected Haldex fluid degrades and fails to lubricate the clutch pack, leading to overheating, clutch plate wear, and eventual seizure of the unit. A failed Haldex causes understeer in corners, loss of quattro function, and in severe cases, binding that affects straight-line driving.
What you would notice
- Noticeable understeer on wet or loose surfaces where quattro should engage
- Shuddering or vibration on tight turns at low speed
- Haldex or quattro warning light if equipped with diagnostic monitoring
- Burning smell from the rear of the vehicle after spirited driving
Typically $300–$4,500 to put right.

A 2014 Audi S3: what is due, and when

Servicing

Nothing left on the schedule

Every milestone is behind this car. The ones below are the receipts worth asking for.

Placed by the car’s age, not read from the dash — 82,800–193,200 km after 12 years.

Timing

Our research does not record which this engine uses, and it depends on the engine rather than the model. Check the owner’s manual rather than assume: on a belt-driven engine, an overdue belt is the failure that takes the engine with it.

Behind it

60,000 kmEnsure the DSG oil and Haldex fluid have been changed.
90,000 kmCheck the water pump and thermostat housing, common wear items around this point.
120,000 kmGood milestone to inspect suspension bushings and check for intake valve carbon buildup.

“Behind it” means the car has driven past that distance, not that the work was done — ask to see the receipts. These are the intervals for the Audi S3 8V · 2.0L Turbo (CJX) - Pre-facelift Performance Quattro · Petrol; only the car’s own service book says what has actually been done to it.

See all 3 issues for this oneDocumented for the exact year and engine you picked, including 1 rated critical.

Engine, transmission & cooling1 critical3

012.0 TFSI (CJXC/IS38) Timing Chain Tensioner Wear

Arrange a cold-start inspection.petrol2013–2020Engine$2,000–$5,500

OccasionalEngine $2,000–$5,500 to fix

The EA888 Gen 3 2.0 TFSI engine fitted to the 8V S3 (CJXC engine code) shares the timing chain tensioner weakness documented across the broader EA888 family. The tensioner's oil feed circuit has marginal oil pressure at cold startup, allowing the chain to slacken momentarily. Over time the chain guide rails wear, and the chain can stretch beyond the tensioner's adjustment range. VW/Audi has issued updated tensioner and guide rail components. The IS38 turbocharger specification in the S3 increases combustion loads, which may marginally accelerate chain wear versus the standard A3 application.

Symptoms to notice

Brief rattling from the top of the engine on cold startup lasting 3-10 seconds
P0016/P0017 camshaft/crankshaft correlation fault codes
Rough running and reduced power after cold start
Catastrophic failure results in engine stoppage without warning

What to check

Arrange a cold-start inspection.
Listen for any chain rattle in the first seconds of startup.
Scan for P0016 and P0017 camshaft timing correlation codes even if no light is currently on — these may be stored as history codes.
Confirm oil service history with intervals no longer than 10,000 km.
Ask whether the tensioner and guide rails have been replaced with updated components.

Where to look: Front of engine — upper and lower timing chain tensioners and guide rails

Parts involved: Timing chain.

Ask the seller

“Has the timing chain or tensioner been replaced or inspected on this engine?”
“Is there any rattle on cold startup?”
“What oil service intervals has the car been on?”

02Haldex Rear Differential Clutch Failure Due to Neglected Service

Check the Haldex service stamp in the service book — it should be listed separately from the main gearbox oil change.petrol2006–2020Transmission$300–$4,500Read the full fault: symptoms, where to look, what to ask the seller

03Water pump and thermostat housing coolant leak (8V S3 2.0 TFSI EA888 Gen3)

petrol2013–2020Cooling$900–$1,800Read the full fault: symptoms, where to look, what to ask the seller

Other Audi S3 engines and years15 documented issues that do not apply to the one you picked.

Engine, transmission & cooling9

011.8T Engine Oil Sludge and Bearing Failure

Check the dipstick for dark, gel-like oil.petrol1996–2003EngineDoes not apply$3,500–$9,000

CommonEngine $3,500–$9,000 to fix

Does not apply

Unconfirmed. This entry does not match our record of which engines and years this model was sold with, and is awaiting review. Confirm it against the car before acting on it.

Early 1.8T engines (AUM/AUQ/ARZ) are highly susceptible to oil sludge accumulation when service intervals exceed 10,000 km or low-quality oil is used. Sludge blocks the oil pickup strainer and narrow oil passages, starving the crankshaft and camshaft bearings of lubrication. This leads to spun bearings, camshaft lobe wear, and eventual catastrophic engine seizure. The 1.8T oiling system has insufficient capacity for extended intervals common in NZ fleet ownership.

Symptoms to notice

Low oil pressure warning light illuminated
Knocking or rattling from the engine on startup
Unusually high oil consumption between services
Sludgy or black oil on the dipstick well before service interval

What to check

Check the dipstick for dark, gel-like oil.
Pull service records and confirm oil change intervals were under 10,000 km with VW/Audi-approved long-life oil.
Request evidence of the last service with oil grade used.
Remove the oil filler cap and use a torch to inspect the camshaft cover internals for thick sludge deposits.

Where to look: Engine internals — camshaft gallery, oil pickup strainer, crankshaft main bearings

Ask the seller

“Can you show me the full service history with oil change dates and intervals?”
“What oil grade has been used — is it VW 502.00 or 504.00 approved?”
“Has the engine ever been taken apart or had bearing work done?”

022.0 TSI High-Pressure Fuel Pump (HPFP) Cam Follower Failure

Request VCDS fuel pressure live data — cranking fuel pressure should reach 5-6 MPa rapidly.petrol2006–2013EngineDoes not apply$3,000–$9,000Read the full fault: symptoms, where to look, what to ask the seller

032.0 TFSI BPY/BWA Timing Chain Tensioner Wear

Start the engine from cold and listen immediately for rattling or ticking from the timing chain cover on the driver's side.petrol2004–2008EngineDoes not apply$900–$1,900

Very commonEngine $900–$1,900 to fix

Does not apply

The hydraulic timing chain tensioner on BPY and BWA 2.0 TFSI engines loses oil pressure when cold, allowing chain slack to develop. A characteristic rattle on startup lasting 2-5 seconds indicates worn tensioner and plastic chain guides. Left unaddressed, the chain can skip a tooth or snap entirely, causing immediate piston-to-valve contact and catastrophic engine destruction. This is one of the most widely reported failures across the EA113 2.0 TFSI engine family and should be treated as a pre-purchase critical check on any example.

Symptoms to notice

Cold start rattle from timing chain area lasting 2-5 seconds
Ticking or clattering immediately after cold start that clears on warm-up
Check engine light with camshaft position sensor fault codes
Rough or lumpy running on cold start

What to check

Start the engine from cold and listen immediately for rattling or ticking from the timing chain cover on the driver's side.
A rattle lasting more than 2 seconds is a strong indicator of tensioner failure.
Verify service history shows tensioner and guide replacement.

Where to look: Timing chain cover on the driver's side of the engine block

Parts involved: Timing chain.

Ask the seller

“Has the timing chain tensioner and guides been replaced?”
“Do you notice any rattle on cold start?”
“Can you provide full service history for this engine?”

041.8T Timing Belt Catastrophic Failure on Neglected Intervals

Demand documentary evidence of timing belt replacement with mileage and date recorded.petrol1996–2003EngineDoes not apply$900–$1,600

OccasionalEngine $900–$1,600 to fix

Does not apply

Unconfirmed. This entry does not match our record of which engines and years this model was sold with, and is awaiting review. Confirm it against the car before acting on it.

The 1.8T engine family (AUM/AUQ/ARZ) uses a rubber timing belt driving both camshafts and the water pump. Audi specifies replacement every 60,000 km or 4 years, whichever comes first. Belt failure on this interference engine causes pistons to contact open valves, bending all valves and destroying the cylinder head. Many NZ examples have unknown or incomplete service histories, making timing belt status a critical pre-purchase check. The water pump is driven by the same belt and should always be replaced simultaneously.

Symptoms to notice

No service records confirming belt replacement
Visible cracks or fraying on the timing belt if inspected through cover
Engine cranks but will not fire after belt snap
Sudden loss of power followed by complete engine stoppage

What to check

Demand documentary evidence of timing belt replacement with mileage and date recorded. The kit includes water pump, tensioner, and idler pulley — confirm all components were replaced together. If records are absent, budget for an immediate replacement. A mechanic can inspect the belt through the upper cover on a cold engine to check for glazing, cracking, or tooth wear.

Where to look: Front of engine — timing belt covers on the auxiliary belt side

Parts involved: Timing belt.

Ask the seller

“When was the timing belt last replaced, and can you show the invoice?”
“Was the water pump and tensioner replaced at the same time?”
“What is the current mileage relative to the last belt change?”

05DSG DQ250 Mechatronic Unit Internal Oil Leak

With engine running, test all gear positions including reverse at crawl speed.2003–2013TransmissionDoes not apply$2,200–$4,800

CommonTransmission $2,200–$4,800 to fix

Does not apply

The DQ250 6-speed wet-clutch DSG fitted to A3 8P models uses a combined electro-hydraulic Mechatronic control unit. Internal O-ring seals within the unit degrade over time, allowing automatic transmission fluid to migrate into the electrical control section. This causes progressive electrical fault storage, erratic gear selection, shuddering at low speed, and eventual loss of drive in forward gears or reverse. In some cases failure is sudden, leaving the vehicle immobile. The Mechatronic unit must be replaced as a complete assembly — seal-only repair is generally unsuccessful in field conditions. DSG fluid service at 60,000 km intervals significantly reduces failure risk.

Symptoms to notice

Jerky or hesitant gear changes especially at low speed
Loss of drive in reverse or first gear
DSG or transmission warning light on instrument cluster
Gearbox entering limp-home or fail-safe mode
Shudder or judder when pulling away from rest

What to check

With engine running, test all gear positions including reverse at crawl speed.
Look for DSG warning lights.
Scan with VCDS for Mechatronic fault codes in the transmission module.
Check underneath the gearbox for any oil weeping around the Mechatronic connector area.
Request DSG fluid service history.

Where to look: Gearbox casing, driver's side — Mechatronic unit bolted to transmission body

Parts involved: Mechatronic / valve body.

Ask the seller

“Has the DSG fluid ever been serviced or changed?”
“Has the transmission ever shown warning lights or entered fail-safe mode?”
“Has the Mechatronic unit been inspected or replaced?”

06Haldex 4th Gen Coupling Filter Blockage — AWD Fault

Check for documented Haldex filter and oil service history at 30,000-40,000 km intervals.2006–2013TransmissionDoes not apply$400–$2,800

CommonTransmission $400–$2,800 to fix

Does not apply

The A3 8P Quattro uses a 4th-generation Haldex electro-hydraulic coupling to engage the rear axle on demand. The coupling relies on an internal electric oil pump to pressurize the multi-plate clutch pack; oil is drawn through a small mesh filter that traps wear debris from the clutch plates and pump components. Audi specifies filter and oil replacement every 30,000-40,000 km but this service is frequently missed by owners and independent workshops. As the filter accumulates debris, flow restriction starves the pump of oil, reducing clutch clamping pressure. The rear wheels progressively receive less torque until AWD engagement ceases entirely. The failure manifests as the Quattro or AWD warning light and converts the vehicle to effective front-wheel-drive under power.

Symptoms to notice

Quattro or AWD system warning light on dashboard
Understeer under power that is disproportionate for AWD vehicle
No detectable rear-wheel engagement on slippery surfaces
Haldex coupling fault codes in VCDS transmission control module scan

What to check

Check for documented Haldex filter and oil service history at 30,000-40,000 km intervals. Use VCDS to scan the Haldex control unit for engagement and coupling fault codes. On a safe low-speed surface, accelerate moderately from rest and note whether rear axle engagement is felt — absence confirms coupling failure or filter blockage. Coupling unit replacement is required if filter and oil change does not restore function.

Where to look: Rear axle assembly, Haldex coupling unit integrated into the rear differential housing

Parts involved: Clutch.

Ask the seller

“When was the Haldex filter and oil last serviced, and can you show documentation?”
“Has the quattro or AWD warning light ever appeared on the dashboard?”
“Has the AWD system been tested or diagnosed by any workshop?”

078P S3 2.0 TFSI Carbon Buildup on Intake Valves

Request an endoscope inspection of the intake valves through the intake ports.petrol2006–2013EngineDoes not apply$500–$1,200Read the full fault: symptoms, where to look, what to ask the seller

081.8T Plastic Coolant Flange and Expansion Tank Cracking

The 1.8T cooling system uses numerous plastic fittings, elbows, and the coolant expansion tank itself.petrol1996–2005CoolingDoes not apply$200–$600

CommonCooling $200–$600 to fix

Does not apply

Unconfirmed. This entry does not match our record of which engines and years this model was sold with, and is awaiting review. Confirm it against the car before acting on it.

The 1.8T cooling system uses numerous plastic fittings, elbows, and the coolant expansion tank itself. These components embrittle and crack with age and heat cycling on high-mileage NZ examples. The most common failure points are the plastic coolant elbow at the rear of the cylinder head and the expansion tank cap seat, which crack and cause sudden coolant loss. Running low on coolant can trigger overheating within minutes on the 1.8T. Many 8L examples in NZ have never had these components proactively replaced.

Symptoms to notice

Low coolant warning light or coolant temperature gauge rising above normal
Sweet smell from the engine bay with no visible external leak
White steam from under the bonnet on a cold morning
Coolant level dropping in the expansion tank between checks

What to check

Inspect all visible coolant hoses and plastic fittings for cracks, dried deposits (white or brown crystalline residue indicating past seepage), and softness from heat damage.
Check the expansion tank for hairline cracks near the cap mounting and the seams.
Confirm the coolant is not contaminated with oil (chocolate-milk appearance in the tank).
Run the engine to operating temperature and check for leaks under pressure.

Where to look: Engine bay — rear coolant elbow, expansion tank, lower coolant hoses

Parts involved: Coolant expansion tank.

Ask the seller

“Have the plastic coolant fittings and expansion tank ever been replaced?”
“Has the car ever overheated or shown coolant warning lights?”
“When was the coolant last flushed and renewed?”

091.8T Crankcase Breather / PCV System Failure

Inspect the PCV hose connected to the valve cover for cracks, oil saturation, or collapse.petrol1996–2003EngineDoes not apply$120–$350

Very commonEngine $120–$350 to fix

Does not apply

Unconfirmed. This entry does not match our record of which engines and years this model was sold with, and is awaiting review. Confirm it against the car before acting on it.

The crankcase ventilation (PCV) system on 1.8T engines uses a plastic valve integrated into the valve cover that separates oil mist from blowby gasses. This plastic valve cracks and degrades with heat cycling, allowing excessive crankcase pressure to build up. The result is oil pushed through the turbocharger seals, burning oil consumption of 1 litre per 1,000 km or more, blue smoke at startup, and fouled spark plugs. A cracked PCV valve also leans the fuel mixture by admitting unmetered air, causing rough running and fault codes.

Symptoms to notice

Blue smoke from the exhaust on cold startup or under boost
Oil consumption exceeding 0.5 litres per 1,000 km
Rough idle and lean fuel trim fault codes stored
Oil residue or oily deposits around the intake hoses and air filter box

What to check

Inspect the PCV hose connected to the valve cover for cracks, oil saturation, or collapse.
Check the intercooler charge pipes for oil pooling.
A VCDS scan for long-term fuel trim values above +10% suggests unmetered air intake.
Remove the oil filler cap while the engine is idling — there should be minimal vacuum but no strong pulsing or blowing.

Where to look: Valve cover — crankcase breather valve and associated vacuum hoses

Parts involved: PCV / oil separator.

Ask the seller

“Has the crankcase breather or PCV valve ever been replaced?”
“Does the car consume any oil between services?”
“Is there any blue smoke from the exhaust on startup?”

Electrical2

01MMI infotainment main unit failure — black screen and dead reversing camera

2021–2022ElectricalDoes not apply$0–$4,000

Very commonElectrical $0–$4,000 to fix

Does not apply

The 8Y A3's infotainment is its weak point and the evidence is unusually strong: in What Car?'s reliability survey 59 per cent of 8Y owners reported a fault, and 44 per cent of those faults were the infotainment system. Owners describe touchscreen freezes, unresponsive inputs, random reboots while driving, Bluetooth dropouts and complete black screens. Audi also ran a safety recall on 2021-2022 cars because the infotainment main unit can be damaged internally when the car is switched off, leaving the reversing camera image dead the next time it is started — and on this car the camera, the climate controls and much of the driving information all live behind the same screen, so one failure takes several functions with it. Early production cars are worst; a soldering defect on some early motherboards caused permanent failures rather than software glitches, and Audi's later software updates progressively fixed most of the rest.

Symptoms to notice

Screen going black, freezing, or rebooting on its own while driving
Reversing camera image not appearing when Reverse is selected
Touchscreen slow or not responding to inputs
Bluetooth or phone connection dropping repeatedly
Warning messages about the emergency call system appearing briefly

What to check

Give the screen a proper workout rather than a glance, and do it with the car switched fully off and on at least twice, because the recall fault only shows on the start after a shutdown. Select Reverse and confirm the camera image appears straight away and is not black, frozen or delayed. Work through the menus — audio, phone, navigation, climate and vehicle settings — and check the touchscreen responds first time everywhere rather than needing a second press. Pair your own phone by Bluetooth and confirm it connects and stays connected on the test drive. Watch for the screen going black or restarting itself while you are moving. Note any message about the emergency call or driver assistance systems, even if it clears by itself. Ask whether the software has been updated at a dealer and whether the infotainment unit has ever been replaced, and ask for the VIN to be checked with Audi for outstanding recalls, which is free. If a workshop inspection is possible: ask for the infotainment software version and any stored control-unit faults to be confirmed.

Where to look: Dashboard — MMI infotainment main unit behind the centre screen

Ask the seller

“Has the infotainment ever frozen, gone black or restarted itself?”
“Has the head unit been replaced or the software updated under recall?”
“Does the reversing camera work every single time?”

021.8T Ignition Coil Pack Failure

Physically inspect each coil pack boot for cracks or carbon tracking.petrol1996–2003ElectricalDoes not apply$150–$450

Very commonElectrical $150–$450 to fix

Does not apply

Unconfirmed. This entry does not match our record of which engines and years this model was sold with, and is awaiting review. Confirm it against the car before acting on it.

The early 1.8T family uses four individual pencil-type ignition coil packs. The original Bosch units have a well-documented failure rate, causing individual cylinders to misfire. The failure pattern is often progressive — one coil fails, is replaced, then another fails weeks later. Running on a misfiring cylinder can damage the catalytic converter from raw fuel exposure. Audi released updated coil pack part numbers (now black-topped rather than grey-topped), and all four should be replaced simultaneously given age on 8L examples.

Symptoms to notice

Engine misfire under load — stumbling or hesitation at acceleration
EPC or engine management warning light illuminated
Rough idle, particularly when cold
Noticeable vibration through the gearknob or steering wheel at idle

What to check

Physically inspect each coil pack boot for cracks or carbon tracking. Confirm whether the updated black-top coil packs have been fitted. Check for stored P030X misfire fault codes. If a workshop inspection is possible: Connect a VAG-COM/VCDS scan tool and read live misfire counters per cylinder.

Where to look: Top of engine — individual coil packs on each spark plug

Parts involved: Ignition coil.

Ask the seller

“Have the ignition coil packs ever been replaced, and with which part numbers?”
“Has the car ever thrown an EPC or engine warning light?”
“Does it idle smoothly when cold?”

Body, brakes, suspension & interior4

01Front passenger airbag folding defect — safety recall 69DZ

This one is settled on paper, not in the driveway.2022InteriorDoes not apply$0–$2,500

RareInterior $0–$2,500 to fix

Does not apply

Audi recalled 4,117 cars from the 2022 model year — 3,681 A3, 420 S3 and 16 RS3 — because the front passenger airbag may have been folded incorrectly during manufacture. An incorrectly folded bag can tear as it inflates and then fail to deploy properly in a crash. Audi and the supplier examined 120 airbags and found deviations in the folding. The remedy is a free replacement of the front passenger airbag module. There is nothing whatever to see or feel from inside the car — the airbag warning light behaves normally because the electrical side of the system is fine — so this is purely a VIN check, and it is a small enough recall that many owners of unaffected cars will tell you truthfully that they never heard of it.

Symptoms to notice

No symptoms at all — the defect is invisible and the warning light stays normal
Airbag warning light staying on would indicate a different, electrical fault
Evidence of previous accident repair around the dashboard

What to check

This one is settled on paper, not in the driveway. Take the VIN from the base of the windscreen or the driver's door jamb and ask an Audi dealer to confirm whether recall 69DZ and every other open campaign has been completed on this specific car — the check is free and it is the only way to know, since nothing about the car will tell you. Ask the seller for recall letters and dealer invoices and read them rather than accepting a summary, because Audi ran several separate campaigns on the 2022 A3 and having one done says nothing about the others. While you are in the car, turn the ignition on and confirm the airbag warning light illuminates and then goes out — a light that never comes on at all can mean the bulb or the warning has been disabled, which is a reason to walk away. Look across the top of the dashboard on the passenger side for panel gaps, mismatched trim or paint overspray that would suggest the car has had accident repair there. If a workshop inspection is possible: ask for the restraint system fault memory to be read alongside the recall check.

Where to look: Dashboard — front passenger airbag module above the glovebox

Ask the seller

“Has recall 69DZ, the passenger airbag recall, been completed on this car?”
“Have all other outstanding Audi campaigns been done, with invoices?”
“Has this car ever been in an accident or had airbags deployed?”

02Front seat belt tensioner safety recall — inadequate restraint in a crash

2022InteriorDoes not apply$0–$1,500

OccasionalInterior $0–$1,500 to fix

Does not apply

Audi recalled 2022 A3 and S3 sedans because the retention force of the seat belt tensioner on the driver and front passenger seats may be insufficient to properly restrain an occupant in a crash. The fix is a free replacement of both front seat belt assemblies. There is nothing to see or feel from the driver's seat — the belt looks and works normally in everyday use, and the defect only matters in the one situation where you cannot afford it to. That makes this purely a paperwork check, and an important one on a car being sold privately or imported, because the original owner notification went out in late 2022 to whoever held the car then.

Symptoms to notice

No symptoms in normal use — the belt operates as expected
Belt slow to retract or not sitting flush against the body
Airbag or restraint warning light on the dash
Belt webbing frayed, twisted or cut

What to check

This is a VIN check first: note the VIN from the base of the windscreen or the driver's door jamb and ask an Audi dealer to confirm whether the seat belt tensioner recall and any other outstanding campaigns have been completed on this car. It costs nothing and it is the only way to be certain. Ask the seller for recall letters or dealer invoices and read them, since a car may have had one campaign done and not another. Sitting in the car, pull each front belt fully out and let it retract, checking it runs smoothly and pulls itself flush rather than hanging slack. Give the belt a sharp tug to confirm it locks. Look along the webbing for fraying, cuts or twisting, and check the buckle latches and releases cleanly. Turn the ignition on and confirm the airbag warning light comes on and then goes out — a light that stays on, or never appears at all, is a reason to stop and ask questions. If a workshop inspection is possible: have the restraint system fault memory read alongside the recall check.

Where to look: Front seats — driver and front passenger seat belt assemblies and tensioners

Parts involved: Timing belt.

Ask the seller

“Has the seat belt tensioner recall been completed, and is there a dealer invoice?”
“Have all other outstanding Audi recalls been done on this car?”
“Has the airbag or restraint warning light ever stayed on?”

038L A3 Sill, Wheel Arch, and Subframe Corrosion

Lift the rubber sill protectors and examine the sill seam for rust perforation.petrol1996–2006Body & RustDoes not apply$500–$5,000

CommonBody & Rust $500–$5,000 to fix

Does not apply

First-generation 8L A3 models are now 20-28 years old, and significant corrosion is found on NZ examples that have been driven in coastal areas or on roads salted with sea spray. The most common locations are the inner and outer sills behind the door steps, the rear wheel arch lips, the front subframe mounting points, and the floor pan above the spare wheel well. Structural corrosion at the front subframe mounts can compromise suspension geometry and front-end rigidity. Japanese grey imports may present lower rust risk due to dry conditions, but NZ coastal use post-import accelerates deterioration.

Symptoms to notice

Bubbling or blistering paint on the lower sill panels and wheel arch lips
Visible rust through the sill covers when the plastic trim is lifted
Soft or flexible floor when pressure is applied to the sill area
Surface rust on the underside of the floor pan and subframe mounts

What to check

Lift the rubber sill protectors and examine the sill seam for rust perforation. Use a magnet to check for filler on the lower front wings and sills. Check the spare wheel well from inside the boot. Any perforated structural rust is a WOF risk and a significant repair cost. If a workshop inspection is possible: Place the vehicle on a hoist and inspect the underside: front subframe mounts, floor pan, jacking points, and rear beam mounting brackets.

Where to look: Lower body — sills, rear wheel arch lips, front subframe mounts, spare wheel well

Parts involved: Chassis and structural rust, Body corrosion.

Ask the seller

“Has the car spent most of its life in NZ, or was it imported from Japan?”
“Has any rust repair or underbody treatment been carried out?”
“Can I put the car on a hoist to inspect the underside?”

04Front Lower Arm Rear Ball Joint Failure

Separately check the front ball joint at 6 and 12 o'clock.2003–2013SuspensionDoes not apply$550–$1,150

CommonSuspension $550–$1,150 to fix

Does not apply

The rear pivot point of the front lower control arm on the 8P A3 incorporates a rubber-bonded ball joint that is integral to the arm casting and cannot be replaced separately. The joint deteriorates with age, road shock, and New Zealand or Australian corrugated road conditions, developing lateral play that manifests as vague or imprecise steering, knocking over bumps, and pulling under braking. Failed joints also cause camber change under cornering, producing rapid inner tyre wear. WOF and roadworthy inspection failures on this item are common on high-mileage 8P examples. The complete lower control arm must be replaced as a unit.

Symptoms to notice

Vague, imprecise, or wander-prone steering feel
Clunking or knocking from front suspension over bumps or dips
Vehicle pulling to one side under firm braking
Uneven or accelerated wear on inner front tyre edge
Steering wheel vibration at motorway speed

What to check

Separately check the front ball joint at 6 and 12 o'clock. Inspect front tyre inner edges for feathering or accelerated wear indicating camber deviation. If a workshop inspection is possible: On a workshop hoist, grasp the front wheel at 3 and 9 o'clock and push and pull to check for lateral play in the lower arm rear pivot.

Where to look: Front subframe, lower control arm rear pivot — both left and right sides

Parts involved: Ball joint.

Ask the seller

“Have the front lower control arms been replaced on this car?”
“Have you noticed any steering vagueness or clunking over bumps?”
“When was the last wheel alignment performed and what was the camber reading?”

Audi S3 faults in detail

Narrowed to the Audi S3 · 2014. Each of these has its own page: the symptoms, where to look, what to ask the seller and what the repair costs. Free, no account needed.

Haldex Rear Differential Clutch Failure Due to Neglected ServiceMajor · Transmission Water pump and thermostat housing coolant leak (8V S3 2.0 TFSI EA888 Gen3)Major · Cooling

What these repairs cost on other cars

Some of the Audi S3’s documented faults are repairs other models share. Each page lists the documented NZ cost for every model it affects.

Other Audi models

Audi A445 documented faults Audi A343 documented faults Audi A634 documented faults Audi TT17 documented faults Audi Q716 documented faults Audi A114 documented faults

Audi S3 buyer questions

Is the Audi S3 reliable?

Like any used car, it depends on the specific example and its service history. Across the 18 documented faults for the Audi S3, the recurring problem areas are engine, interior, and body & rust. A Audi S3 with a full service history and no signs of the issues listed on this page can be a sound buy but each one needs to be checked individually before you commit.

What are the most common problems with a used Audi S3?

We've catalogued 18 known faults for the Audi S3, covering engine, interior, and body & rust. All 18 are written out in full on this page, with the symptoms to notice, what to inspect, and typical repair costs for each. Free to read, no account needed.

How much do repairs cost on a Audi S3?

Most single repairs on the Audi S3 fall between $500–$1,900 at NZ independent-workshop rates. Some of the 18 documented faults cost less and a few cost considerably more, and no one car needs them all. Knowing which ones to look for before you view is what lets you negotiate the price down or walk away.

Should I get a pre-purchase inspection on a Audi S3?

Yes. A Audi S3 inspection focused on its known weak points is the single best way to avoid an expensive mistake. KickTyres gives you a guided, model-specific inspection plus a market valuation and negotiation figure for $24.90 far less than the cost of missing one of the faults on this page.