Skip to content
KickTyres
BMW2000–2023 Critical issues documented

BMW 5 Series G30: common faults & what to check

The G30 is the BMW 5 Series built 2017 onward. It was sold here with the 2.0 turbo petrol, 2.0 plug-in hybrid (530e), and 3.0 turbo petrol. Of the 58 faults documented for the 5 Series, 10 apply to this generation, each with its symptoms, what to inspect and a typical repair cost. Free, no account needed.

Check this exact BMW 5 Series

  • Odometer history
  • Money owing
  • Reported stolen
  • Ownership history
  • Official NZ vehicle register data
  • NZ owned and operated

Type the plate for the free basics. The full record is a paid check from $13.49, one car at a time, no subscription.

No NZ plate yet, or buying in Australia? Pick the generation and engine and start a free check below. New to KickTyres? How the check works →

58

Documented faults

Critical

Most serious

$900–$4,500

Typical repair

8

Systems covered

You're looking at the G30

3 engine variants are documented for this generation. Pick yours to narrow further, or keep reading for the generation as a whole.

Choose a different generation

Now narrow it to the engine

A 1.8 and a 2.4 of the same car do not fail the same way, so the faults below narrow to the engine as well as the year. Free, no account needed.

A 2019 BMW 5 Series is the G30 generation (2017 to now).

Start your free check on this BMW 5 Series

No plate needed. You get the risk score, the buyer's checklist and the guided inspection for the exact car you picked above — not the whole nameplate.

BMW 5 Series G30Engine not picked yet

Pick the engine above first: the 5 Series came with 3, and without it the report has to show all of their faults. Pick the engine

Free. The paid plate check is separate, and stays optional.

Can't confirm for this car

BMW 5 Series · 2019

Narrowed to the year. No engine is recorded for this vehicle. Pick an engine to see which faults apply.

Tell us the engine, or check the engine code on the car, before relying on this.

  • No engine is recorded for this vehicle.

matched on year only

What to look out for

The checks worth doing on a BMW 5 Series before you hand over any money. Every documented fault is listed below, each with its own page.

  • Costly issue

    Cold-soak the vehicle overnight then test the first engagement from Park to Drive - any jolt indicates pump pressure loss.

    See why

    ZF 8HP Electric Oil Pump Failure After Cold Soak

    All G30 5 Series variants use the ZF 8HP automatic transmission which incorporates an electrically-driven auxiliary oil pump to maintain hydraulic pressure during stop-start operation and following extended cold soaks. The electric motor windings in the auxiliary pump degrade over time and fail, causing loss of hydraulic circuit pressure on initial engagement after the vehicle has been parked overnight or for several hours. The driver experiences a hard jolt or brief loss of drive when selecting D or R from cold, followed by normal operation once the mechanical pump builds pressure. Repeated engagement shocks from a failed electric pump accelerate wear on the multi-plate clutch packs and can lead to full transmission failure if unaddressed.

    What you would notice

    • Hard jolt or clunk when engaging Drive or Reverse from cold
    • Momentary loss of drive on initial cold engagement
    • Transmission fault warning light appearing then self-clearing
    • P0218 transmission overtemperature or auxiliary pump fault codes
    • Normal operation resumes after a few seconds once warmed

    Typically $2,200–$5,500 to put right.

  • Costly issue

    Walk around the vehicle and compare ride height at all four corners - any corner sitting noticeably lower is a red flag.

    See why

    Air Suspension Electronic Height Sensor Failure

    G30 5 Series models equipped with optional adaptive air suspension or Integral Active Steering packages include rotary potentiometer-type electronic ride-height sensors at all four corners of the vehicle. These sensors are mounted on the suspension arms in an exposed position where road spray and temperature cycling cause internal corrosion and connector pin oxidation. A failed sensor transmits an incorrect low-height signal to the suspension control module, which interprets it as a collapsed air spring and deflates that corner or triggers a suspension fault mode that disables height adjustment entirely. The result is a visually obvious single-corner sag or a vehicle that cannot raise or lower itself. Motorway or off-road height modes become unavailable when a fault is active.

    What you would notice

    • Visible one-corner drop or uneven ride height front to back
    • Suspension fault warning on instrument cluster
    • Vehicle unable to raise or lower ride height
    • Motorway or comfort ride height modes unavailable
    • Suspension warning preventing speed above 60 km/h in some modes

    Typically $600–$2,500 to put right.

See all 10 issues for this oneDocumented for the exact year and engine you picked, including 2 rated critical.
Engine, transmission & cooling1

01ZF 8HP Electric Oil Pump Failure After Cold Soak

Cold-soak the vehicle overnight then test the first engagement from Park to Drive - any jolt indicates pump pressure loss.2016 onwardTransmissionRead the full fault: symptoms, where to look, what to ask the seller
Body, brakes, suspension & interior1

02Air Suspension Electronic Height Sensor Failure

Walk around the vehicle and compare ride height at all four corners - any corner sitting noticeably lower is a red flag.2016 onwardSuspension
OccasionalSuspension $600–$2,500 to fix

G30 5 Series models equipped with optional adaptive air suspension or Integral Active Steering packages include rotary potentiometer-type electronic ride-height sensors at all four corners of the vehicle. These sensors are mounted on the suspension arms in an exposed position where road spray and temperature cycling cause internal corrosion and connector pin oxidation. A failed sensor transmits an incorrect low-height signal to the suspension control module, which interprets it as a collapsed air spring and deflates that corner or triggers a suspension fault mode that disables height adjustment entirely. The result is a visually obvious single-corner sag or a vehicle that cannot raise or lower itself. Motorway or off-road height modes become unavailable when a fault is active.

Symptoms to notice

  • Visible one-corner drop or uneven ride height front to back
  • Suspension fault warning on instrument cluster
  • Vehicle unable to raise or lower ride height
  • Motorway or comfort ride height modes unavailable
  • Suspension warning preventing speed above 60 km/h in some modes

What to check

Walk around the vehicle and compare ride height at all four corners - any corner sitting noticeably lower is a red flag. Scan the air suspension control module for height sensor fault codes and note which corner is flagged. Physically inspect each sensor mounting point and connector for corrosion, particularly at the rear axle sensors which sit low in the splash zone. Confirm all ride height modes cycle correctly.

Where to look: Suspension control arms at all four corners, rotary height sensor linkages, particularly vulnerable at rear axle

Parts involved: Air suspension strut.

Ask the seller

  • “Is the air suspension fully operational across all height modes?”
  • “Have any suspension warning lights appeared?”
  • “Have any ride height sensors been replaced?”
  • “Can you demonstrate the ride height adjustment function working?”
Depends on the exact engine — 8 moreDocumented for a specific engine we could not confirm from what you picked. Check the engine code on the car.
Engine, transmission & cooling6

01B57 EGR Cooler Gasket Failure & Coolant Ingestion

Check coolant reservoir level and inspect for any drop without visible external leak.diesel2016 onwardCooling
OccasionalCooling $2,500–$6,500 to fix

Can't confirm for this car

The B57 3.0-litre diesel engine uses an exhaust gas recirculation cooler with a brazed aluminium matrix and separate coolant passages to lower EGR gas temperatures before they enter the intake. Sustained thermal cycling between cold starts and high-load operation causes the internal matrix or gasket sealing surfaces to crack, creating a pathway between the coolant circuit and the EGR gas flow. Engine coolant ingresses into the intake manifold and is drawn into the combustion chambers, producing distinctive white or grey sweet-smelling exhaust smoke. The coolant reservoir drops without any visible external leak. If the ingestion is not caught early, sustained coolant entry into one or more cylinders causes hydrolock during cranking, bending connecting rods and producing catastrophic internal engine damage requiring full engine replacement.

Symptoms to notice

  • White or grey smoke from exhaust, especially on startup and under load
  • Unexplained coolant level drop with no external puddles or visible leak
  • Sweet or antifreeze smell from exhaust pipe
  • Engine misfire on one or more cylinders
  • Milky or oily residue visible inside intake manifold
  • Excessive coolant consumption over 1000 km

What to check

  1. Check coolant reservoir level and inspect for any drop without visible external leak.
  2. Start the cold engine and watch the exhaust for white smoke that persists beyond the initial condensation.
  3. Scan for EGR and coolant temperature plausibility fault codes.
  4. If a workshop inspection is possible: Perform a coolant system pressure test and check whether pressure drops when the engine is running.
  5. A cylinder leak-down test can confirm whether coolant is entering a combustion chamber.
  6. Remove the intake ducting downstream of the air filter and inspect the manifold walls for oily milky deposits.

Where to look: EGR cooler unit mounted on top of engine block connected between exhaust manifold and intake manifold

Parts involved: EGR valve.

Ask the seller

  • “Has the EGR cooler ever been replaced?”
  • “Is there any white smoke from the exhaust at startup or under load?”
  • “Has the coolant needed topping up between services?”
  • “Has any workshop investigated unexplained coolant loss?”
  • “Is there a record of any intake manifold or EGR system work?”

02B47 Timing Chain Tensioner Slack & Cold Rattle

Cold-start the engine from fully cold and listen at the front timing cover for chain rattle.diesel2016 onwardEngineRead the full fault: symptoms, where to look, what to ask the seller

03B47 diesel EGR cooler / DPF and AdBlue emissions faults

Ask whether any EGR cooler recall/campaign was carried out.diesel2017–2023Engine
OccasionalEngine $800–$3,500 to fix

Can't confirm for this car

G30 520d/530d diesels use the B47/B57 engines with an EGR cooler that, on some builds, was subject to a coolant-leak recall (a European fire-risk concern), plus the usual DPF and AdBlue/SCR maintenance needs. Short-trip cars clog the DPF and can throw AdBlue and emissions warnings, with SCR repairs pricey out of warranty. Ask about any EGR recall work and check the emissions systems are healthy.

Symptoms to notice

  • EGR / emissions / DPF warning lights
  • AdBlue warning with a restart countdown
  • Reduced power
  • Coolant loss (EGR cooler)

What to check

  1. Ask whether any EGR cooler recall/campaign was carried out.
  2. Check for emissions/AdBlue warnings and confirm none appear on a longer drive.
  3. Check the coolant level.
  4. Ask about the car's trip pattern (short city use loads the DPF).

Where to look: EGR cooler on the engine; DPF and SCR in the exhaust; AdBlue tank

Parts involved: EGR valve, Diesel particulate filter.

Ask the seller

  • “Was any EGR cooler recall work done?”
  • “Any DPF, EGR or AdBlue faults or warnings?”

04B57 AdBlue SCR Dosing Unit Heater Failure

Scan the engine control module and emissions system module for fault codes 4536B0 and 4536B1 as well as any NOx sensor plausibility codes.diesel2016 onwardEngineRead the full fault: symptoms, where to look, what to ask the seller

05B48/B58 VANOS Phaser Control Valve Sticking

Scan for VANOS fault codes P0011/P0012/P0014/P0015.petrol2016 onwardEngineRead the full fault: symptoms, where to look, what to ask the seller

06ZF 8HP Torque Converter Lock-Up Clutch Shudder (G30)

During a highway test drive, hold a steady light throttle between 60 and 80 km/h on a smooth road.petrol2017 onwardTransmission
OccasionalTransmission $300–$4,500 to fix

Can't confirm for this car

G30 5 Series 530i and 540i models with the ZF 8-speed automatic exhibit torque converter lock-up clutch shudder under light throttle load between 40 and 80 km/h. Friction-modifier depletion in degraded transmission fluid causes clutch engagement chatter. BMW's original lifetime fluid specification has been revised in multiple markets following widespread complaints. Fluid-only service by a ZF-approved specialist resolves most cases; a minority of converters require physical replacement where clutch surfaces are glazed.

A cutaway automatic transmission torque converter showing the internal turbine and stator.Example of the part — not this vehicle

A torque converter, sectioned. The lock-up clutch inside is what shudders.

No machine-readable author provided. BerndB~commonswiki assumed (based on copyright claims). · CC BY-SA 3.0 · Wikimedia Commons

Symptoms to notice

  • Vibration or shudder through the drivetrain at 50-80 km/h under light throttle
  • Shudder absent at full throttle or during engine braking
  • Sensation like mild wheel imbalance but consistent and linked to throttle position
  • Possible TCU fault code for torque converter slip

What to check

During a highway test drive, hold a steady light throttle between 60 and 80 km/h on a smooth road. Any regular shudder or vibration felt through the seat or floor is likely torque converter clutch engagement. Check transmission service history — ZF-spec fluid changed by 80,000 km is the standard prevention. If a workshop inspection is possible: Use a BMW-capable scan tool to check for TCU codes if possible.

Where to look: ZF 8HP automatic gearbox torque converter, forward of the main gearbox housing

Parts involved: Torque converter, Clutch.

Ask the seller

  • “Has the automatic transmission fluid been changed?”
  • “Any reports of vibration or shudder at highway speed under light throttle?”
  • “Has a transmission specialist inspected the gearbox?”
Electrical1

01530e plug-in hybrid charging and high-voltage battery faults

Ask to see the car charge from empty and check the claimed electric-only range against original (noticeably reduced range means battery ageing).hybrid2017–2023Electrical
OccasionalElectrical $500–$12,000 to fix

Can't confirm for this car

The G30 530e plug-in hybrid can develop charging faults (charge port, onboard charger or cable errors that stop it charging) and, as the high-voltage battery ages, reduced electric range. A drivetrain/hybrid warning may put it into a reduced state. The high-voltage battery is expensive out of warranty, so confirm it charges fully and holds a reasonable electric range.

Symptoms to notice

  • Won't charge / charging errors
  • Reduced or collapsing electric-only range
  • Hybrid/drivetrain warning light
  • Reduced power mode

What to check

  1. Ask to see the car charge from empty and check the claimed electric-only range against original (noticeably reduced range means battery ageing).
  2. Confirm no hybrid/drivetrain warnings.
  3. Ask whether the charging system has ever faulted and whether it comes with the original cable.

Where to look: High-voltage battery under the car; charge port and onboard charger

Ask the seller

  • “Does it charge fully, and what electric range do you get?”
  • “Any hybrid or charging faults?”
Fluid leaks1

01B48 Engine Oil Cooler Housing Gasket Leak (G30)

Inspect the coolant reservoir for any oily film or emulsification — check the reservoir cap underside carefully.petrol2017 onwardFluid LeaksRead the full fault: symptoms, where to look, what to ask the seller
Other BMW 5 Series engines and years48 documented issues that do not apply to the one you picked.
Engine, transmission & cooling32

01M57 Intake Manifold Swirl Flap Actuator Shaft Failure

Check each individual flap vane is intact and not loose.diesel2003–2010Engine
CommonEngine $3,500–$15,000 to fix

Does not apply

The M57 3.0d diesel engine uses variable intake swirl flaps to improve combustion efficiency at low RPM. The actuating rod connecting the flap assembly is made from a lightweight alloy that is prone to snapping. When it fractures, individual plastic flap vanes can detach and be ingested through the intake into the combustion chambers, causing immediate catastrophic piston and valve damage. Engines that ingest a flap vane typically require full replacement or rebuild.

Symptoms to notice

  • Sudden catastrophic engine knock or seizure, often without warning, following actuating rod fracture
  • Loss of power accompanied by unusual metallic rattling from inlet tract before full failure
  • Fault codes P0087, P0299 (boost/fuel pressure faults) as a flap partially obstructs airflow prior to breaking free
  • Engine cuts out at high load and will not restart

What to check

  1. Check each individual flap vane is intact and not loose.
  2. If a workshop inspection is possible: A preventive fix is to remove all flap vanes entirely and blank off the manifold ports — confirm this has been done on high-mileage examples.
  3. Remove the intake manifold and physically inspect the swirl flap actuating rod for cracks or deformation.

Where to look: Intake manifold underside, swirl flap linkage rod running the length of the manifold

Parts involved: Intake manifold.

02N57 Six-Cylinder Diesel Rear Timing Chain Catastrophic Failure

Verify complete service history and mileage authenticity.diesel2010–2017EngineRead the full fault: symptoms, where to look, what to ask the seller

03N47 Diesel Timing Chain Failure

Listen for timing chain rattle at the rear of the engine on a cold start.diesel2007–2016EngineRead the full fault: symptoms, where to look, what to ask the seller

04SMG Hydraulic Pump & Solenoid Unit Failure

Check the SMG hydraulic fluid level and colour — contaminated dark fluid accelerates solenoid failure.petrol2004–2010TransmissionRead the full fault: symptoms, where to look, what to ask the seller

05N20 Petrol Timing Chain and Guide Failure

petrol2011–2016EngineRead the full fault: symptoms, where to look, what to ask the seller

06S85 5.0L V10 rod-bearing wear / failure (M5 E60)

Demand documented rod-bearing replacement with km.petrol2005–2010EngineRead the full fault: symptoms, where to look, what to ask the seller

07N47/N57 Diesel Intake Swirl Flap Fracture and Engine Ingestion

Ask whether the swirl flaps have been blanked or replaced with updated metal units — this is a common preventive modification.diesel2010–2016Engine
OccasionalEngine $500–$7,000 to fix

Does not apply

Both the N47 and N57 diesel engines use plastic-bodied swirl flaps mounted on a common shaft inside the lower intake manifold to optimise combustion at low loads. The plastic bodies become brittle with heat cycling and the retaining screws are prone to loosening; when a flap breaks free it is ingested into the cylinder head, typically destroying the inlet valve, piston crown, and head in that cylinder. The failure mode is well documented in workshop databases and requires complete upper engine rebuild if ingestion occurs.

Symptoms to notice

  • Sudden violent mechanical knock or bang followed by severe misfire on one cylinder
  • Loss of power on one cylinder with persistent misfire fault codes
  • Metal fragments visible in oil or on the oil filler cap interior
  • Engine management warning light combined with rough running
  • Increased blow-by smoke from the oil filler or crankcase breather

What to check

  1. Ask whether the swirl flaps have been blanked or replaced with updated metal units — this is a common preventive modification.
  2. Inspect for any sign of previous top-end repair or mismatched fasteners on the intake manifold.
  3. If a workshop inspection is possible: With the engine cold, remove the engine cover and inspect the air inlet tract for oil residue.

Where to look: Lower intake manifold, one flap per cylinder port

Parts involved: Intake manifold.

Ask the seller

  • “Have the swirl flaps been inspected, replaced with metal units, or blanked off as a preventive measure?”
  • “Has the car ever suffered a sudden misfire or been to a workshop for an engine internal inspection?”
  • “Is there any history of intake manifold removal or cylinder head work?”

08N20 timing chain guide failure (520i / 528i)

On a cold start listen for a rattle and, on the drive, a whine from the timing end.petrol2010–2017EngineRead the full fault: symptoms, where to look, what to ask the seller

09E39 plastic cooling system failure (water pump, expansion tank, thermostat)

Check the coolant level and look at the plastic expansion tank for cracks/crazing near the seams.petrol2000–2003Cooling
Very commonCooling $800–$2,500 to fix

Does not apply

The E39's cooling system is largely plastic and rubber - expansion tank, thermostat housing, water pump impeller, radiator necks and hoses all go brittle with age and let go, often without warning. A sudden coolant loss overheats the M52/M54 six and can warp the head or blow the gasket. Any E39 with an untouched, original cooling system is a red flag; a full refresh is the accepted preventative.

An annotated photograph of an automotive engine thermostat identifying the wax capsule and both disc valves.Example of the part — not this vehicle

A double-valve engine thermostat, labelled: the wax capsule is what sticks.

Dougsim · CC BY-SA 3.0 · Wikimedia Commons

Symptoms to notice

  • Temperature gauge climbing, especially in traffic
  • Coolant loss / low coolant warning
  • Sweet smell and steam
  • Coolant pooling under the front

What to check

  1. Check the coolant level and look at the plastic expansion tank for cracks/crazing near the seams.
  2. Squeeze the hoses (they shouldn't be rock-hard or mushy).
  3. Watch the temperature gauge on the test drive - it should sit dead centre.
  4. Ask when the cooling system was last refreshed and which parts.

Where to look: Cooling system at the front of the engine bay - pump, tank, thermostat, radiator

Parts involved: Coolant expansion tank, Water pump, Thermostat.

Ask the seller

  • “When was the cooling system last overhauled, and which parts?”
  • “Has it ever overheated?”

10N63 V8 Excessive Oil Consumption Valve Stem Seals

Check the engine oil level at the dipstick immediately — low level on a recently-serviced car is a critical warning sign.petrol2010–2017EngineRead the full fault: symptoms, where to look, what to ask the seller

11N63 4.4L V8 timing chain, injectors & battery drain ('Customer Care Package') (550i F10)

Ask whether the N63 Customer Care Package work was ever carried out and get documentation.petrol2010–2016EngineRead the full fault: symptoms, where to look, what to ask the seller

12S63 4.4L V8 twin-turbo timing-chain guides & injector wear (M5 F10)

Listen for a timing rattle on cold start and scan for camshaft-correlation and misfire codes.petrol2011–2016Engine
OccasionalEngine $2,500–$9,000 to fix

Does not apply

The F10 M5's S63 4.4L twin-turbo V8 (a hotter relation of the N63) shares the family's timing-chain-guide wear and fuel-injector issues. The plastic chain guides and tensioners wear, risking a timing rattle and, if neglected, a jumped chain; the direct injectors can fail and cause misfires and rough running. It is a strong engine when maintained, but chain and injector history matter on a high-km, hard-used M5.

The front of a dual overhead camshaft engine with the timing cover removed, exposing the timing chain and sprockets.Example of the part — not this vehicle

The front of a twin-cam engine with the timing cover off — chain, sprockets and guides.

Logansenf · CC BY-SA 4.0 · Wikimedia Commons

Symptoms to notice

  • Timing rattle on cold start / correlation codes
  • Misfire, rough idle, hard starting (injectors)
  • Loss of power

What to check

  1. Listen for a timing rattle on cold start and scan for camshaft-correlation and misfire codes.
  2. Ask whether the timing chain/guides or any injectors have been replaced, and how hard the car has been driven or tracked.

Where to look: Timing chains, guides and injectors on the 4.4L V8

Parts involved: Timing chain, Fuel injector, Turbocharger.

Ask the seller

  • “Any timing rattle on cold start or correlation codes?”
  • “Have the timing guides or injectors been replaced?”

13N63 4.4L V8 twin-turbo heavy oil consumption & valve stem seals (550i F10)

Ask how much oil it uses between services - anything under ~1,500 km per litre is a red flag.petrol2010–2016EngineRead the full fault: symptoms, where to look, what to ask the seller

14N57 3.0L six-cylinder rear-mounted timing chain wear (530d / 535d)

On a genuinely cold first start, listen at the rear of the engine near the bulkhead for a rattle.diesel2010–2017Engine
OccasionalEngine $3,500–$7,500 to fix

Does not apply

The F10 530d and 535d use the N57 straight-six, whose timing chain runs from the rear (gearbox end) of the engine like the four-cylinder N47's. The N57 chain is far more robust than the N47's and often lasts the life of the car, but the heavier six still wears its chain and guides, and the rear location makes replacement a gearbox-out job. A rattle from the bellhousing on a high-km example is the tell. This is distinct from the 2.0-litre N47 chain issue already recorded on the 520d.

The front of a dual overhead camshaft engine with the timing cover removed, exposing the timing chain and sprockets.Example of the part — not this vehicle

The front of a twin-cam engine with the timing cover off — chain, sprockets and guides.

Logansenf · CC BY-SA 4.0 · Wikimedia Commons

Symptoms to notice

  • Metallic rattle from the back of the engine on cold start
  • Timing/camshaft correlation fault codes
  • Chain rattle that rises with engine speed
  • Rough running after a chain event

What to check

  1. On a genuinely cold first start, listen at the rear of the engine near the bulkhead for a rattle.
  2. Ask whether the chain has been done on a very high-km car.
  3. Scan for timing-correlation codes before committing.

Where to look: Timing chain at the rear (gearbox end) of the six-cylinder engine

Parts involved: Timing chain.

Ask the seller

  • “Any rattle from the back of the engine on cold start?”
  • “Has the timing chain been inspected or replaced?”

15N55 Turbo Wastegate Actuator Rattle

Start the engine cold and listen immediately for a chattering rattle from the turbocharger region on the right side of the engine bay.petrol2010–2017EngineRead the full fault: symptoms, where to look, what to ask the seller

16N57S 3.0L multi-turbo boost/actuator failure (535d / M550d)

On the drive, do firm accelerations from low and mid revs to confirm both turbos deliver smooth, strong boost with no flat spots or limp mode.diesel2011–2017EngineRead the full fault: symptoms, where to look, what to ask the seller

17N54 / N55 3.0L twin/single-turbo wastegate rattle & charge-pipe cracking (535i F10)

Start cold and listen for wastegate rattle from the turbos; blip and release the throttle.petrol2010–2016EngineRead the full fault: symptoms, where to look, what to ask the seller

18N57D30 Diesel Injector Copper Washer Failure and Combustion Gas Leak

Inspect around the base of each injector for carbon tracking or black sooting on the exterior of the head.diesel2010–2016Engine
OccasionalEngine $1,200–$6,500 to fix

Does not apply

The N57 3.0-litre six-cylinder diesel uses high-clamping-load injectors seated with copper crush washers. When these washers fail to seal — due to improper torquing on reinstallation or heat fatigue — combustion gases track past the injector seat and into the cylinder head, causing localised erosion of the aluminium head around the injector bore. In severe cases coolant can be drawn into the cylinder from a compromised head gasket, causing hydrolocking and connecting-rod damage. Early detection is critical because head repair or replacement is expensive.

A single common-rail diesel fuel injector photographed against a plain background.Example of the part — not this vehicle

A common-rail diesel injector. Contamination damages the nozzle at the tip.

Panoha · CC BY-SA 3.0 · Wikimedia Commons

Symptoms to notice

  • Black carbonised soot tracks radiating from the injector seat on the exterior of the cylinder head
  • White or grey exhaust smoke, particularly on cold start or under load
  • Unexplained coolant level drop without visible external leak
  • Rough running or misfire on one or more cylinders with injector-related fault codes
  • Sweet or acrid smell from the exhaust or engine bay

What to check

  1. Inspect around the base of each injector for carbon tracking or black sooting on the exterior of the head.
  2. Check for white exhaust smoke on startup (coolant) or a sweet smell from the exhaust.
  3. Request coolant level history and check the expansion tank for an oily film or emulsification.
  4. If a workshop inspection is possible: A compression and leak-down test across all cylinders is advisable.

Where to look: Top of cylinder head, six injector bores on the N57 inline-six

Parts involved: Fuel injector.

Ask the seller

  • “Have any injectors ever been removed and reinstalled, and were the copper washers replaced each time?”
  • “Has the car ever had a coolant loss that was not traced to an external leak?”
  • “Is there any history of rough running, misfires, or injector fault codes?”

19M57 3.0L six-cylinder turbo VNT sticking / low boost (530d / 535d)

Do firm accelerations on the test drive and confirm smooth, strong boost with no sudden drop or limp mode.diesel2003–2010EngineRead the full fault: symptoms, where to look, what to ask the seller

20F10 xDrive Transfer Case Electronics Fault — AWD Warning

Check for 4A82, 4A83, 4A84 (ATC motor/clutch engagement faults).2010–2016Transmission
OccasionalTransmission $800–$4,500 to fix

Does not apply

The F10-generation 5 Series fitted with xDrive all-wheel drive uses an electronically-controlled transfer case (Verteilergetriebe) with a wet multi-plate clutch pack managed by the ATC module. The ATC control module or its wiring connector can develop faults causing the transfer case to default to a rear-wheel-drive-only limp mode. The instrument cluster displays an 'xDrive Deactivated' or '4x4 System Malfunction' warning. The fault is often triggered by software, connector corrosion, or ATC module failure rather than mechanical clutch wear.

Symptoms to notice

  • 'xDrive Deactivated — Drive moderately' or equivalent warning displayed on iDrive screen, often appearing in wet or cold conditions
  • Amber or red four-wheel drive warning light on the instrument cluster with no obvious mechanical noise from driveline
  • Vehicle handling noticeably changes to rear-biased drive with reduced traction in poor conditions
  • Fault codes 4A82, 4A83, or 480A stored in ATC module relating to transfer case clutch engagement or motor circuit

What to check

  1. Check for 4A82, 4A83, 4A84 (ATC motor/clutch engagement faults).
  2. Inspect the ATC module wiring harness connector for corrosion or pushed-back pins — this is located on the top of the transfer case and is vulnerable to water ingress from the transmission tunnel drain point.
  3. Verify transfer case fluid level and condition.
  4. If a workshop inspection is possible: Connect BMW ISTA diagnostic tool and read all fault codes from the ATC/xDrive module.

Where to look: Transfer case (ATC 35L or ATC 45L unit) mounted behind the gearbox on the transmission tunnel, with ATC control module attached to the casing

Parts involved: Transfer case.

21S85 5.0L V10 throttle-actuator & VANOS pump failure (M5 E60)

Scan for throttle-actuator and VANOS codes and ask whether actuators or the VANOS pump have been rebuilt or replaced.petrol2005–2010Engine
CommonEngine $2,000–$4,500 to fix

Does not apply

The S85 V10 M5 uses multiple electronic throttle actuators whose plastic gears wear out, dropping the car into limp mode with reduced power and codes. The engine also has a high-pressure VANOS pump that supplies the variable-valve-timing system; when it weakens it causes rough running, power loss and VANOS faults. Both are common age-related M5 repairs and, combined with the rod bearings, are why the E60 M5 is cheap to buy and expensive to keep.

Symptoms to notice

  • Limp mode / reduced power (throttle actuators)
  • Rough idle, hesitation, VANOS fault codes
  • Erratic throttle response

What to check

Scan for throttle-actuator and VANOS codes and ask whether actuators or the VANOS pump have been rebuilt or replaced. A history of limp-mode events points here.

Where to look: Throttle actuators on the intake side and VANOS pump on the 5.0L V10

Ask the seller

  • “Have the throttle actuators or VANOS pump been rebuilt/replaced?”
  • “Has it dropped into limp mode?”

22S85 5.0L V10 SMG III hydraulic pump failure (M5 E60)

On the test drive feel for clunky or failed SMG shifts and watch for gearbox warnings.petrol2005–2010Transmission
OccasionalTransmission $2,000–$4,000 to fix

Does not apply

Most E60 M5s came with the SMG III single-clutch automated manual, driven by an electro-hydraulic pump. The pump and its accumulator wear and fail, causing jerky or failed shifts, hesitation and warning lights as the system struggles to build pressure. Replacement pumps are expensive and the clutch itself is a wear item on top. A manual-converted or well-serviced SMG car is preferable; a neglected SMG is a costly repair waiting to happen.

Symptoms to notice

  • Jerky, harsh or delayed gearchanges
  • Transmission or SMG warning lights
  • Hesitation as the system builds pressure
  • Failure to select gear

What to check

  1. On the test drive feel for clunky or failed SMG shifts and watch for gearbox warnings.
  2. Ask whether the SMG pump, accumulator or clutch have been replaced.
  3. Confirm whether the car is SMG or a manual conversion.

Where to look: SMG hydraulic pump and actuator unit on the gearbox

Parts involved: Clutch.

Ask the seller

  • “Has the SMG pump, accumulator or clutch been replaced?”
  • “Does it shift cleanly or does it clunk and hesitate?”

23N54 High-Pressure Fuel Pump Failure

Scan for fault codes 29DC (fuel pressure regulation), 2FBB (rail pressure), or 30BA.petrol2007–2010EngineRead the full fault: symptoms, where to look, what to ask the seller

24N55B30 High-Pressure Fuel Pump (HPFP) Failure

During a test drive, note any hesitation, stumble, or surge at light throttle cruise — classic signs of marginal fuel pressure.petrol2010–2016Engine
OccasionalEngine $1,400–$3,200 to fix

Does not apply

The N55B30 twin-scroll turbocharged inline-six uses a high-pressure direct-injection fuel pump driven off the camshaft. The pump cam follower (tappet) can wear prematurely, and the pump itself suffers internal seal and plunger failure, causing fuel pressure drop in the high-pressure rail. The engine management system attempts to compensate but eventually the car stalls, misfires, or refuses to start. BMW issued TSBs and an extended warranty in some markets covering early HPFP failures.

Symptoms to notice

  • Hesitation or stumble under light throttle, particularly at cruise on a warm engine
  • Hard or extended cranking required to start when engine is warm
  • Intermittent rough idle that clears under acceleration
  • Check Engine light with fuel rail pressure fault codes (P0087, P1093)
  • Stalling at idle or low speed in severe cases

What to check

During a test drive, note any hesitation, stumble, or surge at light throttle cruise — classic signs of marginal fuel pressure. Ask whether the car has ever stalled unexpectedly or had difficulty starting when warm. If a workshop inspection is possible: Connect an OBD scanner and check for fault codes P0087 (fuel rail pressure too low), P1093, or BMW-specific 29D0/29CD codes.

Where to look: Top rear of the engine, driven by the inlet camshaft lobe

Parts involved: High-pressure fuel pump.

Ask the seller

  • “Has the high-pressure fuel pump or its cam follower ever been replaced?”
  • “Has the car ever stalled unexpectedly, been difficult to start when warm, or shown a fuel system warning?”
  • “Were any fuel pressure fault codes found during the car's service history?”

25Valvetronic Motor & Eccentric Shaft Sensor Failure

Inspect the eccentric shaft sensor wiring harness and connector at the front of the valve cover for corrosion or chafing.petrol2003–2010EngineRead the full fault: symptoms, where to look, what to ask the seller

26Diesel EGR Cooler Cracking and Coolant Loss

Check the coolant expansion tank level and look for a white residue or emulsification indicating combustion gas contamination.diesel2007–2016CoolingRead the full fault: symptoms, where to look, what to ask the seller

27N62 V8 VANOS Electric Oil Pump Failure

Scan for VANOS fault codes on both intake and exhaust camshafts for both banks.petrol2003–2010Engine
OccasionalEngine $700–$2,200 to fix

Does not apply

The N62 V8 uses a dedicated electric oil pump — referred to in BMW technical literature as the Elmoil unit or EOP (Electric Oil Pump) — to supply hydraulic pressure for the VANOS variable camshaft timing system on both banks. When the electric motor or pump internals fail, VANOS actuation is lost. This causes rough running, poor throttle response, and triggers VANOS fault codes. The pump is a wear item that deteriorates with age and mileage on E60 545i and 550i models.

Symptoms to notice

  • VANOS-related check engine light and fault codes
  • Rough or uneven idle especially on cold start
  • Noticeable loss of power and sluggish throttle response
  • Engine hunting or surging at idle when warm

What to check

  1. Scan for VANOS fault codes on both intake and exhaust camshafts for both banks.
  2. Check live VANOS position data to confirm the system is actuating correctly.
  3. Listen for any abnormal clicking or whirring from the electric oil pump area near the front of the engine.
  4. Verify engine oil level and condition, as low oil can accelerate pump wear.

Where to look: VANOS electric oil pump, front of engine near timing cover

Ask the seller

  • “Have any VANOS fault codes or warning lights appeared?”
  • “Has the car had any rough idle, power loss, or engine surging issues?”

28N55 3.0L electric water pump & thermostat failure (535i F10)

Ask when the electric water pump and thermostat were last replaced.petrol2010–2016Cooling
CommonCooling $900–$1,900 to fix

Does not apply

The turbo 535i's electric water pump and thermostat are wear items that commonly fail around 80,000-130,000 km, sometimes without warning. A failed pump lets the engine overheat quickly and drop to limp mode; continuing to drive risks head-gasket damage. Specialists replace the pump and thermostat together. On a heavy F10 535i this is a when-not-if maintenance cost buyers should budget for.

An annotated photograph of an automotive engine thermostat identifying the wax capsule and both disc valves.Example of the part — not this vehicle

A double-valve engine thermostat, labelled: the wax capsule is what sticks.

Dougsim · CC BY-SA 3.0 · Wikimedia Commons

Symptoms to notice

  • Overheating or 'reduced power after cooling' message
  • Loss of power / limp mode
  • Weak cabin heat
  • Coolant warning

What to check

  1. Ask when the electric water pump and thermostat were last replaced.
  2. Watch the temperature on a longer drive and scan for cooling/thermostat codes.
  3. Budget for it on any 535i past ~100,000 km with no record.

Where to look: Electric water pump and thermostat on the 3.0L block

Parts involved: Water pump, Thermostat.

Ask the seller

  • “Has the electric water pump and thermostat been replaced?”
  • “Has it ever overheated or gone into reduced power?”

29Electric water pump failure and overheating (N52, N20 2.0T and N55 3.0T petrol, F10/F11)

Check the coolant temperature gauge behaviour during a test drive — it should stabilise in the normal band within a few minutes of driving.petrol2010–2016CoolingRead the full fault: symptoms, where to look, what to ask the seller

30VANOS variable-valve-timing rattle and seal wear (M52TU/M54)

On a cold start listen for a rattle from the timing cover area.petrol2000–2003Engine
CommonEngine $800–$2,000 to fix

Does not apply

The E39's VANOS variable valve timing units use rubber seals that harden and wear, causing a rattle, rough idle, hesitation and lost low-end torque. It is expected on high-km M52TU/M54 sixes and specialists rebuild the units with upgraded seals. Not dangerous, but a car with tired VANOS feels flat and lumpy, and it is a common negotiating point.

Symptoms to notice

  • Rattle from the front of the engine, worst when cold
  • Rough or uneven idle
  • Hesitation and weak low-end pull
  • Loss of power

What to check

On a cold start listen for a rattle from the timing cover area. On the drive feel for weak low-rpm torque and hesitation. Ask whether the VANOS seals have been done. A scan for VANOS/timing codes helps.

Where to look: VANOS units on the front of the cylinder head

Ask the seller

  • “Have the VANOS seals been rebuilt?”
  • “Does it feel flat at low revs or rattle when cold?”

31N20/N55 Direct Injection Carbon Buildup on Intake Valves

Check service records for any walnut blasting or intake valve cleaning at or beyond 80,000 km.petrol2011–2016Engine
CommonEngine $500–$1,300 to fix

Does not apply

Both the N20B20 and N55B30 use gasoline direct injection (GDI), which means fuel is injected directly into the combustion chamber rather than over the intake valves. As a result, the oil vapour from the crankcase ventilation system deposits carbon on the backs of the intake valves with no fuel wash to remove it. Over 60,000–120,000 km, carbon deposits restrict airflow to individual cylinders, causing rough idle, misfires, and loss of power. The only effective remedy is walnut-shell media blasting of the intake ports with the manifold removed.

Symptoms to notice

  • Rough or lumpy idle, particularly when cold, that smooths above 1500 RPM
  • Hesitation or stumble under light throttle openings below 2000 RPM
  • Minor misfire fault codes (P0300–P0304) that are not associated with ignition system faults
  • Gradual reduction in fuel economy compared to earlier ownership
  • Slight power loss at low RPM that becomes less noticeable under full throttle

What to check

Check service records for any walnut blasting or intake valve cleaning at or beyond 80,000 km. During the test drive, note any rough idle when cold, hesitation on light throttle, or minor misfire that smooths out at higher RPM. If a workshop inspection is possible: An endoscope inspection of the intake ports via the manifold runners can reveal carbon buildup directly.

Where to look: Intake valve stems and port walls inside the cylinder head, accessed by removing the intake manifold

Parts involved: PCV / oil separator.

Ask the seller

  • “Have the intake valves ever been cleaned (walnut blasted) and at what mileage?”
  • “Has the car ever had rough idling, misfires, or hesitation under light throttle that was investigated?”
  • “Was the car predominantly used on short city trips, which accelerate deposit formation?”

32N52 2.5/3.0 petrol valve cover gasket oil leak onto the exhaust manifold

With engine warm, open the bonnet and look for oil residue around the valve cover perimeter and on the top of the exhaust manifold.petrol2003–2017Engine
Very commonEngine $280–$750 to fix

Does not apply

The N52 2.5 and 3.0 petrol six in the 5 Series commonly leaks oil from the valve cover gasket onto the exhaust manifold. The gasket material hardens and shrinks with age and heat cycling, losing its seal at the cover perimeter and particularly around the spark plug tubes (petrol engines). Oil drips onto the hot exhaust manifold directly below, producing a burning oil smell and in some cases light smoke from the engine bay. Left unaddressed, oil can saturate ignition coils causing misfire faults.

Symptoms to notice

  • Burning oil smell from the engine bay, particularly noticeable after spirited driving or when stationary with engine running
  • Visible oil residue or baked-on carbon deposits on the exhaust manifold or heat shield
  • Engine misfire fault codes (P030X series) on petrol engines caused by oil contaminating ignition coil bases in plug tube wells
  • Light blue-grey smoke from engine bay on deceleration after highway driving

What to check

With engine warm, open the bonnet and look for oil residue around the valve cover perimeter and on the top of the exhaust manifold. On N52 petrol engines, remove ignition coils and inspect each plug tube well for pooled oil indicating failed tube seals. The gasket set includes the perimeter gasket and individual plug tube seals and should always be replaced together.

Where to look: Valve (cam) cover top of engine, gasket perimeter and spark plug tube seals — oil tracks down to exhaust manifold on the side of the engine

Parts involved: Exhaust manifold, Rocker / valve cover.

Electrical5

01Electric water pump connector short circuit, fire-risk recall REC-006063 (5 Series 2.0 N20 turbo petrol)

petrol2011–2016Electrical
RareElectrical $0–$1,800 to fix

Does not apply

On the N20 2.0 litre turbo four-cylinder (F10 520i and 528i), oily blow-by liquid from the crankcase ventilation system can collect on the intake air hose and drip onto the electric water pump's plug connector. If liquid gets into the connector it can short circuit, overheat and in rare cases start an engine bay fire. BMW Australia recalled these cars in August 2024 (REC-006063, campaign 0011800700; US campaign 24V608) to inspect and if needed replace the pump and connector and fit a protective shield, free of charge. Ask for proof the recall work has been done.

Symptoms to notice

  • Coolant temperature or engine overheating warning
  • Drivetrain malfunction or reduced power message
  • Burning electrical smell from the engine bay
  • Electric water pump stops working and the engine overheats

What to check

Ask the seller or a BMW dealer to confirm by VIN that recall REC-006063 (water pump plug connector and shield) has been completed, and ask for the invoice or service record. With the bonnet open, use a torch to look around the front of the engine for oily residue, scorched plastic or melted wiring, and smell for burnt electrical insulation after the test drive. Watch the temperature and warning lights during a 20 minute drive. If a workshop inspection is possible: have the electric water pump connector checked for oil contamination or corrosion and confirm the shield is fitted.

Where to look: Front of the engine, low down: the electric water pump and its plug connector below the intake air hose

Parts involved: Water pump, Turbocharger.

Ask the seller

  • “Has the water pump connector recall (REC-006063) been done, and can I see the paperwork?”
  • “Has the water pump ever been replaced?”
  • “Has the car ever overheated or shown a coolant warning?”

0248V Mild Hybrid Belt-Starter-Alternator (BSA) Failure (G30 LCI)

Check for any drivetrain or hybrid system warnings in stored fault code history.petrol2020 onwardElectrical
OccasionalElectrical $2,000–$6,000 to fix

Does not apply

G30 LCI facelift variants from approximately 2020 with the 48-volt mild hybrid system incorporate a belt-driven starter-alternator (BSA). The BSA unit has a documented failure pattern including belt-drive failure, BSA motor faults, and 48V lithium battery degradation that leaves the vehicle in limp mode or unable to start via the belt-starter path. Replacement requires specialist 48V tooling not available at many NZ/AU independent workshops. Parts availability for the 48V system has been limited in NZ/AU, extending repair lead times.

Symptoms to notice

  • Vehicle enters limp mode with drivetrain or mild hybrid warning
  • 48V system fault message on the instrument cluster
  • Engine start difficulty or failure via belt-starter path
  • Battery charge warning related to the 48V subsystem

What to check

  1. Check for any drivetrain or hybrid system warnings in stored fault code history.
  2. Inspect the BSA drive belt at the front of the engine for wear or glazing.
  3. Ask whether the vehicle has had any drivetrain or electrical faults repaired under warranty since 2020.
  4. If a workshop inspection is possible: Scan specifically for 48V BSA fault codes — standard OBD2 readers will not capture these; a BMW-capable scan tool is required.

Where to look: Front of engine belt-driven BSA unit; 48V lithium battery pack in boot area

Parts involved: Alternator, Starter motor.

Ask the seller

  • “Has the 48V mild hybrid system ever triggered a warning or fault code?”
  • “Has the belt-starter-alternator or 48V battery been replaced?”
  • “Are there any outstanding warranty claims on the drivetrain or electrical systems?”

03E60 iDrive, control-module and battery-drain gremlins

Work through the iDrive, windows, lights and central locking.2003–2010Electrical
CommonElectrical $200–$2,000 to fix

Does not apply

The tech-heavy E60 is known for electrical gremlins: iDrive freezes and reboots, door and light control modules play up, warning lights appear and clear, and a tired battery (which must be 'registered' when replaced) causes a cascade of random faults. Most are nuisance-level, but chasing an intermittent module fault can be costly. A car showing multiple dash warnings deserves a full scan.

Symptoms to notice

  • iDrive freezing or rebooting
  • Random dash warning lights
  • Windows/lights/central locking acting up
  • Flat battery / faults after standing

What to check

  1. Work through the iDrive, windows, lights and central locking.
  2. Note any warning lights and have the car scanned for stored faults across modules.
  3. Ask whether the battery has been replaced and correctly registered.

Where to look: iDrive head unit and control modules throughout the car; battery in the boot

Parts involved: 12V battery.

Ask the seller

  • “Are there any warning lights or stored fault codes?”
  • “Was the battery replaced and registered?”

04F10 electronics: iDrive, comfort-access and battery-drain faults

Test the iDrive, keyless entry, windows, lights and driver-assist features.2010–2017Electrical
CommonElectrical $200–$2,000 to fix

Does not apply

The F10 carries a lot of electronics that develop faults with age: iDrive freezes and reboots, comfort access/keyless entry plays up, and parasitic battery drains leave the car flat after standing (often needing a battery that must be coded). Individually minor, but an intermittent electrical fault can be time-consuming and costly to trace. Work through every electronic feature on inspection.

Symptoms to notice

  • iDrive freezing or rebooting
  • Keyless/comfort access unreliable
  • Flat battery after standing
  • Random dash warnings

What to check

  1. Test the iDrive, keyless entry, windows, lights and driver-assist features.
  2. Ask whether the car has ever gone flat when parked and whether the battery was replaced and registered.
  3. A full module scan is worthwhile.

Where to look: iDrive and control modules throughout; battery in the boot

Parts involved: 12V battery.

Ask the seller

  • “Does it ever go flat when parked?”
  • “Any warning lights or iDrive faults, and was the battery registered?”

05Window regulators, pixel displays and blower final-stage resistor

Operate every window fully up and down.2000–2003Electrical
CommonElectrical $150–$900 to fix

Does not apply

Age-related electrical niggles are near-universal on the E39: plastic window-regulator clips break so windows drop or jam, the dashboard/OBC and radio displays lose pixels (rows of the display go blank), and the heater blower's final-stage resistor fails so the fan only works on full or not at all. None are dangerous but together they are characteristic and add up. Check every window and electrical function.

Symptoms to notice

  • Window slow, jamming or dropping into the door
  • Missing pixel rows in the cluster/OBC or radio display
  • Heater fan only working on high (or not at all)
  • Intermittent electrical faults

What to check

  1. Operate every window fully up and down.
  2. Check the instrument-cluster and radio displays for missing pixel lines.
  3. Run the heater blower through all fan speeds.
  4. Note anything that only works intermittently.

Where to look: Door window regulators; instrument/radio displays; blower resistor behind the glovebox area

Ask the seller

  • “Do all four windows work smoothly?”
  • “Are there any dead pixels in the displays, and does the fan work on all speeds?”
Body, brakes, suspension & interior8

01E60 Front Lower Control Arm Ball Joint Separation

Inspect the lower ball joint boot for splitting or grease loss.2003–2010Suspension
OccasionalSuspension $600–$1,800 to fix

Does not apply

On the E60-generation 5 Series (2003–2010), the front suspension lower control arms use a pressed-in ball joint that can separate from the arm under load, particularly on aged or corroded examples. Separation causes immediate and total loss of front wheel steering and geometry control, making the vehicle undriveable and creating severe collision risk. The issue is exacerbated by road salt corrosion in colder climates and by inspection intervals that focus on boot condition rather than joint integrity.

The front wheel of a car splayed outward with the lower control arm hanging down after a ball joint separation.Example of the part — not this vehicle

A separated lower ball joint: the control arm has dropped and the wheel has splayed out under the guard.

Elfix · CC0 · Wikimedia Commons

Symptoms to notice

  • Clunking or knocking from front suspension over bumps and during cornering, especially on cold mornings
  • Vague or wandering steering with reduced front-end stability at speed
  • Visible tyre wear anomalies (camber-related edge wear) caused by geometry shift as joint deteriorates
  • In failure: sudden dramatic pull to one side accompanied by loud bang and loss of directional control

What to check

Inspect the lower ball joint boot for splitting or grease loss. Any perceptible vertical play in the lower ball joint on an E60 warrants immediate arm replacement — joint-only replacement is not recommended as the arm is sold as an assembly. If a workshop inspection is possible: With the vehicle on a hoist, grasp each front wheel at 6 and 12 o'clock positions and rock it to check for play.

Where to look: Front lower control arm — ball joint at the outer (wheel carrier) end of both left and right lower arms

Parts involved: Ball joint.

02Takata driver airbag inflator recall PRA 2018/17191 (F10/F11 5 Series, 2013-2016)

Some 2013 to 2016 F10/F11 5 Series cars (all engines) were built with a Takata driver's airbag whose propellant can absorb moisture over time.2013–2016Interior
OccasionalInterior $0–$1,500 to fix

Does not apply

Some 2013 to 2016 F10/F11 5 Series cars (all engines) were built with a Takata driver's airbag whose propellant can absorb moisture over time. In a crash the inflator can over-pressurise and rupture, throwing metal fragments at the driver, which can cause serious injury or death. BMW Australia recalled F Series cars in a staged campaign from December 2018 (PRA 2018/17191) to replace the airbag free of charge, and a separate 2024 recall (REC-006035) covers cars later fitted with a steering wheel that has a Takata inflator. Have the VIN checked to confirm the recall work is done. Not every car is in the recall; a dealer check of the VIN is the only way to know.

Symptoms to notice

  • No visible symptom: the defect only shows when the airbag deploys
  • Airbag warning light on the dash may indicate an airbag module has been disturbed or replaced with a non-genuine part

What to check

  1. Ask the seller for the BMW dealer invoice showing the Takata driver airbag recall (PRA 2018/17191) was done, and ring a BMW dealer with the VIN to confirm there are no open airbag recalls.
  2. Check the airbag warning light comes on at start-up and goes out after a few seconds.
  3. Look at the steering wheel: if it has been swapped for a different style, ask where it came from, because swapped wheels are covered by a separate Takata recall (REC-006035).
  4. If a workshop inspection is possible: have a BMW dealer read the vehicle recall history by VIN and check the airbag module part label against the recall list.

Where to look: Driver airbag in the centre of the steering wheel

Ask the seller

  • “Has the Takata driver airbag recall been done, and do you have the dealer invoice?”
  • “Has the steering wheel ever been replaced or swapped for a different style?”
  • “Has the airbag warning light ever come on?”

03EDC Electronic Damper Control Solenoid Failure

Check for any suspension or chassis warning lights on the instrument cluster.2003–2010SuspensionRead the full fault: symptoms, where to look, what to ask the seller

04F11 Touring Rear Air Suspension Compressor and Strut Failure

Inspect the vehicle from the rear at rest — all four corners should be level.2010–2017SuspensionRead the full fault: symptoms, where to look, what to ask the seller

05E61 Touring rear self-levelling air suspension compressor and air spring failure

Park the car overnight on level ground and check rear ride height in the morning — any sag vs the front indicates air loss.2003–2010Suspension
OccasionalSuspension $1,500–$5,000 to fix

Does not apply

E61 Touring models with self-levelling rear air suspension can suffer compressor and air spring failure. The compressor motor and dryer are failure-prone: the compressor brushes wear out, the dryer element becomes saturated, and the air struts themselves can leak. A failed compressor causes the rear of the car to sag, triggering warning lights and — on cars with adaptive dampers — compromising ride and handling control. Air strut leaks are identified by the compressor running continuously or the car sitting low overnight.

Symptoms to notice

  • Rear of car sitting noticeably lower than normal or sagging overnight
  • Suspension warning light or ride height warning on dash
  • Compressor audible running for extended periods when parked
  • Harsh ride from rear if air struts have deflated

What to check

  1. Park the car overnight on level ground and check rear ride height in the morning — any sag vs the front indicates air loss.
  2. Listen for the compressor running after the car is switched off.
  3. Scan for suspension fault codes.
  4. Ask whether the car has the self-levelling suspension and whether it has ever had compressor or strut work.

Where to look: Air compressor in the boot/trunk area or wheel arch. Air struts at the rear shock absorber position.

Parts involved: Air suspension strut.

Ask the seller

  • “Does the car have self-levelling or air suspension?”
  • “Has the air compressor or rear air struts been replaced?”
  • “Has the rear ever sagged or a suspension warning light appeared?”

06E39 rust in rear wheel arches, sills and jacking points

Run your hand around the inside and lip of the rear arches feeling for bubbling.2000–2003Body & Rust
CommonBody & Rust $500–$4,000 to fix

Does not apply

The E39 rusts in well-known spots: the rear wheel arch lips, the sills (especially rear, where sound-deadening soaks up moisture and rots the metal behind the plastic covers), the jacking points, and the boot floor/spare-well. On older NZ cars and salt-exposed imports this can be structural and a WoF failure. It is often hidden, so it must be looked for specifically rather than assumed clean.

Symptoms to notice

  • Bubbling paint at rear arch lips
  • Rot at the sills/jacking points
  • Damp or rusty boot floor
  • Crunchy metal when pressed

What to check

Run your hand around the inside and lip of the rear arches feeling for bubbling. Peel back the plastic sill covers if you can and check the metal behind, and inspect the jacking points. Lift the boot carpet and check the spare-wheel well. Any structural rust here is a WoF and safety issue.

Where to look: Rear wheel arches, sills, jacking points, boot floor/spare-well

Parts involved: Body corrosion.

Ask the seller

  • “Has there been any rust repair to the arches or sills?”
  • “Can I see under the sill covers and boot carpet?”

07Servotronic Speed-Sensitive Steering Valve Failure

2003–2010Suspension
OccasionalSuspension $800–$2,200 to fix

Does not apply

The Servotronic system on the E60/E61 5 Series uses a solenoid valve on the steering rack to vary power assistance with road speed, light when parking and firmer at motorway speeds. The valve can stick, and the valve, its wiring or the module that drives it can fail, which leaves the steering stuck heavy at low speed or too light at speed and usually stores a Servotronic fault code. Owners report that replacing the valve alone does not always cure it, so a proper diagnosis of the circuit matters. On a test drive, check that the steering is light when parking and firms up as speed rises.

Symptoms to notice

  • Steering effort does not change between low-speed parking and highway driving
  • Steering is consistently too heavy or too light at all speeds
  • DSC, steering, or chassis warning light on instrument cluster
  • Steering groans or hesitates during slow-speed manoeuvres

What to check

  1. Test steering effort at car park speed versus 80 km/h motorway speed — effort should be noticeably heavier at highway speed on a functioning Servotronic system.
  2. Scan chassis module for fault codes referencing Servotronic, EPS, or steering assist.
  3. Check power steering fluid level and condition.
  4. Inspect the Servotronic valve wiring at the steering rack for corrosion or chafing.

Where to look: Servotronic solenoid valve integrated into power steering rack

Parts involved: Steering rack.

Ask the seller

  • “Has the power steering or Servotronic system ever required repair?”
  • “Are there any active or stored warning lights related to steering or DSC?”

08E60 Rear Integral Link Bushing Collapse

Check rear tyre wear pattern — severe inner edge wear is the primary indicator.petrol2003–2010SuspensionRead the full fault: symptoms, where to look, what to ask the seller
Fluid leaks3

01N62 V8 Valley Pan Gasket Oil Leak

Ask the owner how frequently engine oil requires topping up.petrol2003–2010Fluid LeaksRead the full fault: symptoms, where to look, what to ask the seller

02N52 electric water pump, oil filter housing and valve-cover leaks

On the drive watch for temperature spikes and any overheat warning (electric pump).petrol2003–2010Fluid Leaks
CommonFluid Leaks $800–$2,500 to fix

Does not apply

E60 six-cylinder petrols (N52/N53) suffer a failing electric water pump (which can strand the car and overheat it), plus oil leaks from the oil-filter-housing gasket and valve-cover gasket that drip onto hot components and smell of burning oil. All are common by 120,000-180,000 km. Individually manageable, but a car needing all three at once is a meaningful bill.

Symptoms to notice

  • Overheating / coolant warning with no external leak (electric pump)
  • Burning-oil smell after driving
  • Oil residue down the side of the block
  • Rough idle if oil reaches plugs

What to check

  1. On the drive watch for temperature spikes and any overheat warning (electric pump).
  2. Look for oil weeping from the oil filter housing (front of engine) and valve cover, and smell for burning oil.
  3. Ask whether the water pump and gaskets have been done.

Where to look: Electric water pump on the side of the engine; oil filter housing and valve cover

Parts involved: Rocker / valve cover, Water pump.

Ask the seller

  • “Has the electric water pump been replaced?”
  • “Are there oil leaks from the filter housing or valve cover?”

03Oil filter housing and valve/timing cover gasket oil leaks

Look around the oil filter housing and valve cover for wet oil and check for oil on the belt.2010–2017Fluid Leaks
CommonFluid Leaks $500–$1,500 to fix

Does not apply

F10 petrol and diesel engines commonly weep oil from the oil-filter-housing gasket and valve/timing-cover gaskets as the seals harden, dripping onto the exhaust and belt and causing a burning-oil smell. Left alone, oil can contaminate the belt or reach the alternator. It is routine ageing rather than catastrophe, but a heavily oil-soaked engine bay is a bargaining point and a service the car needs.

Symptoms to notice

  • Burning-oil smell after driving
  • Oil residue on the front/side of the engine
  • Oil drips on the driveway
  • Low oil level over time

What to check

  1. Look around the oil filter housing and valve cover for wet oil and check for oil on the belt.
  2. Smell for burning oil after the test drive.
  3. Ask whether these gaskets have been replaced.

Where to look: Oil filter housing and valve/timing cover on the engine

Parts involved: Alternator.

Ask the seller

  • “Any oil leaks from the filter housing or covers?”
  • “Have those gaskets been replaced?”

BMW 5 Series faults in detail

Narrowed to the BMW 5 Series · 2019. Each of these has its own page: the symptoms, where to look, what to ask the seller and what the repair costs. Free, no account needed.

B47 Timing Chain Tensioner Slack & Cold RattleCritical · EngineB48 Engine Oil Cooler Housing Gasket Leak (G30)Major · Fluid LeaksB48/B58 VANOS Phaser Control Valve StickingMajor · EngineB57 AdBlue SCR Dosing Unit Heater FailureMajor · EngineZF 8HP Electric Oil Pump Failure After Cold SoakMajor · Transmission

What these repairs cost on other cars

Some of the BMW 5 Series’s documented faults are repairs other models share. Each page lists the documented NZ cost for every model it affects.

Other BMW models

BMW 3 Series88 documented faultsBMW 1 Series50 documented faultsBMW X342 documented faultsBMW X541 documented faultsBMW 2 Series27 documented faultsBMW X126 documented faults

BMW 5 Series buyer questions

Is the BMW 5 Series reliable?

Like any used car, it depends on the specific example and its service history. Across the 58 documented faults for the BMW 5 Series, the recurring problem areas are engine, transmission, and cooling. A BMW 5 Series with a full service history and no signs of the issues listed on this page can be a sound buy but each one needs to be checked individually before you commit.

What are the most common problems with a used BMW 5 Series?

We've catalogued 58 known faults for the BMW 5 Series, covering engine, transmission, and cooling. All 58 are written out in full on this page, with the symptoms to notice, what to inspect, and typical repair costs for each. Free to read, no account needed.

How much do repairs cost on a BMW 5 Series?

Most single repairs on the BMW 5 Series fall between $900–$4,500 at NZ independent-workshop rates. Some of the 58 documented faults cost less and a few cost considerably more, and no one car needs them all. Knowing which ones to look for before you view is what lets you negotiate the price down or walk away.

Should I get a pre-purchase inspection on a BMW 5 Series?

Yes. A BMW 5 Series inspection focused on its known weak points is the single best way to avoid an expensive mistake. KickTyres gives you a guided, model-specific inspection plus a market valuation and negotiation figure for $24.90 far less than the cost of missing one of the faults on this page.