Skip to content
KickTyres
Nissan2006–2022 Critical issues documented

Nissan Qashqai: common faults & what to check

Thinking about buying a used Nissan Qashqai (2006–2022) in New Zealand? We've documented 28 known faults for this model spanning engine, body & rust, suspension, and electrical. Each researched and verified before it's published. The most serious issues here are rated critical. Every one is listed below with its symptoms and repair cost, and each has its own page with where to look and what to ask the seller. Free, no account needed.

Check this exact Nissan Qashqai

  • Odometer history
  • Money owing
  • Reported stolen
  • Ownership history
  • Official NZ vehicle register data
  • NZ owned and operated

Type the plate for the free basics. The full record is a paid check from $13.49, one car at a time, no subscription.

No NZ plate yet, or buying in Australia? Pick the generation and engine and start a free check below. New to KickTyres? How the check works →

28

Documented faults

Critical

Most serious

$550–$1,800

Typical repair

8

Systems covered

Which Nissan Qashqai are you looking at?

5 generation variants documented. Pick the shape you recognise: the faults, the servicing and the timeline below all narrow to it. Free, no account needed.

Hybrid

1 variant documented

Now narrow it to the engine

A 1.8 and a 2.4 of the same car do not fail the same way, so the faults below narrow to the engine as well as the year. Free, no account needed.

Start your free check on this Nissan Qashqai

No plate needed. You get the risk score, the buyer's checklist and the guided inspection for the exact car you picked above — not the whole nameplate.

Nissan QashqaiEngine not picked yet

Pick the engine above first: the Qashqai came with 6, and without it the report has to show all of their faults. Pick the engine

Free. The paid plate check is separate, and stays optional.

Can't confirm for this car

Nissan Qashqai

Nothing has been narrowed yet, so nothing below is a claim about a particular car. Pick a year and an engine to see which faults apply.

Tell us the engine, or check the engine code on the car, before relying on this.

matched on no vehicle context

What to look out for

The checks worth doing on a Nissan Qashqai before you hand over any money. Every documented fault is listed below, each with its own page.

  • Serious issue

    Cold-start and listen carefully for any chain rattle or ticking from the front of the engine.

    See why

    1.2 DIG-T Timing Chain Guide Disintegration

    The HRA2DDT 1.2-litre turbocharged engine (marketed as DIG-T) uses plastic timing chain guides that are undersized for the sustained heat cycling of a turbocharged application. The guides crack and shed fragments into the oil sump from as low as 60,000 km, and once the guide fails the timing chain loses lateral support and can derail, jump timing, or snap entirely. This is a terminal failure mode that typically destroys the cylinder head and sometimes the block, as piston-to-valve contact occurs at high speed.

    What you would notice

    • Rattling or slapping noise from the front of the engine, worse on cold start but sometimes persistent when warm
    • Plastic debris visible in drained oil or caught in cut-open oil filter element
    • Check engine light with camshaft/crankshaft correlation codes (P0016, P0017)
    • Sudden catastrophic engine noise followed by loss of power — chain derailment event
    • Engine stall at speed with no warning, not restarting

    Typically $2,500–$14,000 to put right.

  • Serious issue

    Check the intercooler and intake pipes for oily residue indicating turbo oil blow-by.

    See why

    1.2 DIG-T Turbo Bearing Failure from Oil Coking

    The HRA2DDT 1.2-litre turbocharged petrol engine in the J11 Qashqai is prone to premature turbocharger bearing failure caused by oil coking. When the engine is switched off after spirited driving, heat soak from the small turbocharger with no dedicated water-cooling circuit carbonises residual oil in the bearing housing. Over time coked oil restricts lubrication, destroys the bearing, and allows the turbine shaft to contact the housing walls. Resulting metal debris contaminates the oil circuit and can damage the engine block itself. The failure is significantly accelerated by infrequent oil changes, non-synthetic oil, or short warm-up periods before driving hard.

    What you would notice

    • Whining or grinding noise from the turbo area under acceleration
    • Excessive blue or white smoke from the exhaust under boost
    • Noticeable loss of power and sluggish throttle response
    • Oily residue inside the intercooler hoses or air intake pipes
    • Turbo actuator or boost pressure fault codes stored in the ECU

    Typically $2,200–$6,500 to put right.

  • Serious issue

    Check the vehicle's recall history for KBA 14969R / R24C8 (AU REC-006324) and confirm the BMS software update has been applied.

    See why

    e-POWER battery-management software fault (limp mode / loss of drive)

    J12 Qashqai e-POWER cars are subject to a large safety recall (KBA 14969R, Nissan code R24C8; Australia REC-006324) covering roughly 94,000 UK/EU vehicles built 2021-2024 plus a smaller AU batch. Incorrect Battery Management System (BMS) software can miscalculate the high-voltage battery state of charge, causing it to fluctuate and drop the car into emergency/limp-home mode. Owners report a 'Battery Management Fault - Service Now' warning, sharply reduced power and, in some cases, an inability to restart. The dealer remedy is a free BMS software reflash; always confirm it has been done.

    What you would notice

    • Battery Management Fault / Service Now warning message
    • Sudden loss of drive power or limp-home mode while driving
    • Warning lights and reduced performance
    • Occasional failure to restart

    Typically $0–$300 to put right.

  • Serious issue

    Probe suspect areas with a pick or screwdriver to check for soft or hollow metal.

    See why

    Rear Subframe Corrosion at Mounting Points

    The rear subframe on J10 Qashqai models is susceptible to corrosion at its unibody mounting points, particularly in the coastal and high-rainfall environments common across NZ and AU. Road salt, mud trapped around the mounting brackets, and inadequate factory undercoating allow rust to penetrate the subframe steel and the surrounding body mounting pockets. In advanced cases the mounting bolt holes corrode through, causing subframe movement that manifests as rear-end rattles and imprecise handling. Structurally compromised mounting points represent a serious safety hazard and result in WOF or roadworthy rejection. Repair requires specialist rust treatment, plate welding, or full subframe replacement in severe cases.

    What you would notice

    • Rattling or clunking from rear of vehicle over rough road surfaces
    • Imprecise or wandering rear-end handling at highway speed
    • Visible rust, bubbling paint, or scaling metal under the rear of the vehicle
    • WOF or roadworthy rejection for structural corrosion at subframe mounts

    Typically $1,600–$6,000 to put right.

  • Costly issue

    Drive from cold at 20-40 km/h and feel for a judder or vibration through the drivetrain.

    See why

    Jatco RE0F10D CVT Judder and Transmission Failure

    The Jatco RE0F10D continuously variable transmission fitted to petrol Qashqai models develops a characteristic judder or shudder during low-speed acceleration from rest, caused by degradation of the steel push-belt and the torque converter clutch solenoid. The CVT fluid (NS-3) breaks down and loses its friction-modifier properties, causing the belt to slip micro-incrementally under load. In advanced cases the transmission overheats, goes into limp mode, and eventually fails completely, requiring full replacement as the unit is not economically rebuildable in most NZ/AU markets.

    What you would notice

    • Pronounced shudder or vibration felt through the floor and seat during gentle acceleration from 10-40 km/h
    • Hesitation or surge when pulling away from traffic lights
    • Transmission warning light or D-flashing on the instrument cluster
    • Burnt or discoloured CVT fluid on the dipstick or during a drain
    • Transmission entering limp mode (locked to a single ratio) at operating temperature

    Typically $4,500–$9,500 to put right.

  • Costly issue

    Start the engine cold and immediately listen for a metallic rattle from the timing chain cover at the front of the engine.

    See why

    MR20DE Timing Chain Tensioner Cold Start Rattle

    The hydraulic timing chain tensioner in the MR20DE 2.0L petrol loses oil pressure when the engine sits overnight. On cold start, the slack chain rattles loudly against the timing cover for 5 to 30 seconds until oil pressure builds and the tensioner re-engages. Repeated rattle events accelerate chain and guide wear, eventually risking chain jump and catastrophic valve damage. This is the single most widely reported defect on J10 Qashqais in NZ and AU owner forums and workshop records.

    What you would notice

    • Loud rattling or clattering noise from front of engine on cold start
    • Noise disappears within 30 seconds of start as oil pressure builds
    • Possible check engine light or camshaft position sensor fault codes
    • Rough idle immediately after cold start in cold weather

    Typically $900–$2,500 to put right.

See all 28 documented issuesEverything researched for the Nissan Qashqai, including 5 rated critical.
Depends on which engine this Nissan Qashqai has — 28Each of these is documented for one particular engine. Pick the year and engine above to see which of them apply.
Engine, transmission & cooling13

011.2 DIG-T Timing Chain Guide Disintegration

Cold-start and listen carefully for any chain rattle or ticking from the front of the engine.petrol2014–2019EngineRead the full fault: symptoms, where to look, what to ask the seller

021.2 DIG-T Turbo Bearing Failure from Oil Coking

Check the intercooler and intake pipes for oily residue indicating turbo oil blow-by.petrol2013–2021EngineRead the full fault: symptoms, where to look, what to ask the seller

03Jatco RE0F10D CVT Judder and Transmission Failure

Drive from cold at 20-40 km/h and feel for a judder or vibration through the drivetrain.petrol2013–2017TransmissionRead the full fault: symptoms, where to look, what to ask the seller

04CVT Belt Slip and Judder Under Load

Test drive under full acceleration from low speed on a hill or on-ramp.petrol2006–2013Transmission
CommonTransmission $3,800–$9,500 to fix

Can't confirm for this car

The Jatco RE0F10A (J10) and RE0F10D (J11) continuously variable transmissions are prone to steel push-belt and pulley slip causing a pronounced shudder or judder under moderate to heavy acceleration, particularly when pulling away from low speeds or climbing inclines. Worn belt and pulley surfaces cause slippage that the TCM misidentifies as normal operation until driveability becomes noticeably impaired. Fluid degradation accelerates wear; Nissan NS-2 CVT fluid changes at or before 60,000 km are essential. Full rebuild or replacement is the only lasting fix once slip begins and internal damage has occurred.

Symptoms to notice

  • Shudder or judder felt through the drivetrain and floor under acceleration
  • Hesitation or flaring of engine revs without corresponding acceleration
  • Delayed engagement when selecting Drive or Reverse from Park
  • Burning or overheated transmission smell after hill driving
  • CVT warning light or transmission temperature warning in instrument cluster

What to check

  1. Test drive under full acceleration from low speed on a hill or on-ramp.
  2. Check for shudder, slip, or rev flare.
  3. Inspect CVT fluid colour via dipstick or fill plug — it should be red or pink, not brown or burnt-smelling.
  4. Request documented CVT fluid change history.

Where to look: Transmission casing in the engine bay and transmission tunnel beneath the vehicle

Parts involved: CVT belt and pulleys.

Ask the seller

  • “Has the CVT fluid ever been changed and at what mileage?”
  • “Has the transmission been serviced, rebuilt, or replaced?”
  • “Do you notice any judder, shudder, or hesitation when accelerating?”

05MR20DD Timing Chain Stretch and Cold-Start Rattle

Cold-start the engine from fully cold and listen at the front of the engine for a metallic rattle in the first 3-5 seconds.petrol2013–2019EngineRead the full fault: symptoms, where to look, what to ask the seller

061.2 DIG-T Excessive Engine Oil Consumption

Check the oil level cold on the dipstick and note it carefully, then recheck after a test drive.petrol2014–2019EngineRead the full fault: symptoms, where to look, what to ask the seller

07All-Mode 4WD Rear Coupling Unit Shudder and Seizure

With the vehicle in Auto 4WD mode, drive slowly through several tight full-lock turns in a car park.petrol2014–2021Transmission
OccasionalTransmission $1,500–$4,000 to fix

Can't confirm for this car

The electronically controlled rear coupling unit on 4WD Qashqai models (supplied by BorgWarner) transfers torque to the rear wheels via an electro-hydraulic clutch pack. The coupling's internal fluid degrades and the multi-plate clutch pack wears, producing a pronounced shudder or vibration when cornering at low speed or when the 4WD system engages under load. In cases where the unit has seized or the coupling ECU has failed, the vehicle may pull or crab-walk on tight turns, causing serious tyre scrub and drivetrain stress.

Symptoms to notice

  • Juddering or vibration through the floor and steering wheel during slow tight turns in 4WD Auto mode
  • Clunking sound when the 4WD system engages from 2WD mode
  • 4WD warning light or ALL MODE 4x4 system fault on the instrument cluster
  • Abnormal tyre wear on all four corners due to drivetrain binding
  • Vehicle pulling or resisting during sharp parking manoeuvres

What to check

With the vehicle in Auto 4WD mode, drive slowly through several tight full-lock turns in a car park. Any shudder, vibration, or binding sensation through the steering or floor indicates coupling wear. Check for fault codes in the 4WD control module. Inspect the coupling unit casing under the rear of the vehicle for fluid leaks or heat discolouration.

Where to look: Rear axle assembly, coupling unit mounted ahead of the rear differential between the propeller shaft and rear axle

Parts involved: Clutch.

Ask the seller

  • “Has the rear coupling unit fluid ever been replaced, or has the coupling itself been replaced?”
  • “Have you noticed any shudder or vibration when making tight turns in car parks, especially in 4WD mode?”
  • “Has any 4WD warning light or drivetrain fault code appeared on the dashboard?”

08Haldex Rear AWD Coupling Failure from Fluid Neglect

On AWD variants, check whether Haldex fluid service is recorded in the service book.petrol2006–2013Transmission
OccasionalTransmission $1,200–$3,500 to fix

Can't confirm for this car

AWD J10 Qashqais use a Haldex rear coupling to engage rear-wheel drive. The unit has its own fluid reservoir that requires periodic replacement (every 40,000 km). Neglected fluid causes internal clutch pack wear; severely degraded fluid leads to coupling seizure. A seized coupling either fails to engage the rear wheels (understeer on loose surfaces) or locks permanently (binding and shudder in tight cornering). Replacement of the complete unit is typically required.

Symptoms to notice

  • Binding, vibration, or shudder when turning tightly at low speed (seized coupling)
  • Loss of rear traction on gravel or wet roads (failed-open coupling)
  • Burning smell from rear drivetrain under load
  • AWD system warning light

What to check

  1. On AWD variants, check whether Haldex fluid service is recorded in the service book.
  2. Drive in a tight circle on a hard surface at low speed – any binding or shudder indicates coupling problems.
  3. Ask specifically about off-road use or mud exposure, which contaminate the coupling fluid faster.

Where to look: Rear drivetrain – Haldex AWD coupling unit on the propshaft or at the rear differential

Parts involved: Clutch.

Ask the seller

  • “Has the Haldex coupling fluid been serviced and at what intervals?”
  • “Is this an AWD or 2WD variant?”
  • “Has any binding or shudder been noticed when parking or cornering?”

091.6 dCi R9M DPF Clogging on Urban Cycles

Connect an OBD2 scanner and check for DPF soot loading percentage and any related fault codes.diesel2013–2021EngineRead the full fault: symptoms, where to look, what to ask the seller

10MR20DE Timing Chain Tensioner Cold Start Rattle

Start the engine cold and immediately listen for a metallic rattle from the timing chain cover at the front of the engine.petrol2006–2013EngineRead the full fault: symptoms, where to look, what to ask the seller

11HR16DE Timing Chain Tensioner Rattle on Cold Start

Cold-start the engine and listen for a metallic chain rattle from the front of the engine lasting more than 2–3 seconds.petrol2013–2019Engine
CommonEngine $900–$2,200 to fix

Can't confirm for this car

The HR16DE 1.6-litre engine uses a hydraulic timing chain tensioner that relies on oil pressure to maintain chain tension. On cold starts the tensioner bleeds down overnight, and during the critical seconds before oil pressure builds the chain slaps against the guide rails, producing a characteristic metallic rattle from the front of the engine. Repeated episodes accelerate guide rail and chain wear; in neglected cases the chain stretches beyond the tensioner's range, causing variable camshaft timing errors, rough running, and ultimately chain skip or breakage.

The front of a dual overhead camshaft engine with the timing cover removed, exposing the timing chain and sprockets.Example of the part — not this vehicle

The front of a twin-cam engine with the timing cover off — chain, sprockets and guides.

Logansenf · CC BY-SA 4.0 · Wikimedia Commons

Symptoms to notice

  • Metallic rattling noise from front of engine on cold start, typically lasting 2–10 seconds before quietening
  • Camshaft timing fault codes (P0011, P0014, P0340) stored in ECU, often accompanied by rough idle after cold start

What to check

Cold-start the engine and listen for a metallic chain rattle from the front of the engine lasting more than 2–3 seconds. Check for camshaft position/crankshaft correlation fault codes (P0011, P0014, P0340). Inspect oil level and condition; low or degraded oil worsens bleed-down. If rattle persists beyond 5 seconds on cold start, the tensioner and guide rails should be inspected.

Where to look: Front of engine block, timing cover side — accessible after removing cam cover and timing cover

Parts involved: Timing chain.

Ask the seller

  • “Does the engine rattle on cold start before settling down?”
  • “Has the timing chain tensioner or chain ever been replaced or inspected?”

12MR20DD Intake Valve Carbon Deposit Buildup

Remove intake manifold and inspect valve backs with a bore scope or direct light; look for thick carbon crust on valve stems and port walls.petrol2014–2021EngineRead the full fault: symptoms, where to look, what to ask the seller

13MR20DD Engine Coolant Thermostat Housing Leak

petrol2013–2019Cooling
OccasionalCooling $300–$750 to fix

Can't confirm for this car

The MR20DD engine uses a plastic thermostat housing integrated with the coolant outlet that is prone to cracking at the sealing surface or at the housing body as the plastic ages and heat cycles. Coolant leaks from this housing can drip onto the exhaust manifold causing steam and burning smell, and if undetected lead to low coolant levels and overheating. The housing is located in a partially obscured position that makes small weeps easy to miss during a casual inspection.

An annotated photograph of an automotive engine thermostat identifying the wax capsule and both disc valves.Example of the part — not this vehicle

A double-valve engine thermostat, labelled: the wax capsule is what sticks.

Dougsim · CC BY-SA 3.0 · Wikimedia Commons

Symptoms to notice

  • White or rusty coolant staining or dried residue on or below the thermostat housing
  • Coolant level dropping in the reservoir between top-ups without evidence of internal consumption
  • Sweet antifreeze smell inside the cabin or from the engine bay after a run
  • Steam visible from the engine bay when the vehicle is warm and parked
  • Overheating warning if the leak is substantial and coolant level drops below the minimum

What to check

With the engine cold, inspect the thermostat housing and all coolant hose connections at the front and rear of the engine for white mineral deposits, dried coolant residue, or active weeping. Check the coolant reservoir level. After a test drive, re-inspect the housing area for steam or fresh coolant residue. If a workshop inspection is possible: Pressure-test the cooling system if any doubt exists.

Where to look: Front of the MR20DD engine, thermostat housing on the upper coolant outlet pipe near the radiator top hose connection

Parts involved: Thermostat.

Ask the seller

  • “Has the thermostat or thermostat housing ever been replaced, or has there been any coolant leak in the engine bay?”
  • “Has the coolant level ever dropped unexpectedly, and when was the coolant last changed?”
  • “Has the vehicle ever overheated or shown a high temperature warning?”
Electrical4

01e-POWER battery-management software fault (limp mode / loss of drive)

Check the vehicle's recall history for KBA 14969R / R24C8 (AU REC-006324) and confirm the BMS software update has been applied.hybrid2022 onwardElectricalRead the full fault: symptoms, where to look, what to ask the seller

02Electric Power Steering Failure

Scan for EPS fault codes.2007–2013Electrical
OccasionalElectrical $600–$2,200 to fix

Can't confirm for this car

EPS system can develop a fault causing loss of power assistance.

Symptoms to notice

  • Sudden loss of power steering assistance with EPS warning light
  • Heavy steering especially at low speeds and during parking

What to check

  1. Scan for EPS fault codes.
  2. Test steering — any heavy or inconsistent feel indicates EPS fault.

Where to look: EPS rack and column assembly

Parts involved: Steering rack.

Ask the seller

  • “Has the electric power steering failure been inspected or repaired?”

0312V battery drain when parked (mild-hybrid and e-POWER)

Ask how long the car can sit before it fails to start and whether it has needed jump-starts.2022 onwardElectricalRead the full fault: symptoms, where to look, what to ask the seller

04Air Conditioning Compressor Clutch Failure

Test AC during test drive.2007–2013Electrical
CommonElectrical $400–$1,500 to fix

Can't confirm for this car

AC compressor clutch bearing wears causing squealing when AC is engaged.

Symptoms to notice

  • Squealing from engine front when AC is switched on
  • Noise stops when AC is switched off

What to check

  1. Test AC during test drive.
  2. Listen for squealing from engine front when AC is engaged.

Where to look: AC compressor on front of engine

Parts involved: Clutch.

Ask the seller

  • “Has the air conditioning compressor clutch failure been inspected or repaired?”
Body, brakes, suspension & interior10

01Rear Subframe Corrosion at Mounting Points

Probe suspect areas with a pick or screwdriver to check for soft or hollow metal.2006–2013Body & Rust
OccasionalBody & Rust $1,600–$6,000 to fix

Can't confirm for this car

The rear subframe on J10 Qashqai models is susceptible to corrosion at its unibody mounting points, particularly in the coastal and high-rainfall environments common across NZ and AU. Road salt, mud trapped around the mounting brackets, and inadequate factory undercoating allow rust to penetrate the subframe steel and the surrounding body mounting pockets. In advanced cases the mounting bolt holes corrode through, causing subframe movement that manifests as rear-end rattles and imprecise handling. Structurally compromised mounting points represent a serious safety hazard and result in WOF or roadworthy rejection. Repair requires specialist rust treatment, plate welding, or full subframe replacement in severe cases.

Symptoms to notice

  • Rattling or clunking from rear of vehicle over rough road surfaces
  • Imprecise or wandering rear-end handling at highway speed
  • Visible rust, bubbling paint, or scaling metal under the rear of the vehicle
  • WOF or roadworthy rejection for structural corrosion at subframe mounts

What to check

  1. Probe suspect areas with a pick or screwdriver to check for soft or hollow metal.
  2. Check inner wheel arches for corrosion bubbling from behind the inner liner.
  3. If a workshop inspection is possible: With the vehicle on a hoist inspect all four rear subframe mounting points and the surrounding unibody metal for rust perforation, bubbling paint, or movement under load.

Where to look: Rear underside of vehicle at the four subframe-to-unibody mounting brackets

Parts involved: Chassis and structural rust, Body corrosion.

Ask the seller

  • “Has the vehicle ever been undercoated or received rust-proofing treatment?”
  • “Has it been used near the coast or regularly on unsealed gravel roads?”
  • “Do you notice any rattles or clunks from the rear end over rough surfaces?”

02Rear Trailing Arm Bush Collapse

The J11 Qashqai rear multi-link suspension uses large hydraulic or rubber-bonded bushes in the trailing arm mounts.2014–2021Suspension
OccasionalSuspension $500–$1,400 to fix

Can't confirm for this car

The J11 Qashqai rear multi-link suspension uses large hydraulic or rubber-bonded bushes in the trailing arm mounts. These bushes are designed to allow controlled compliance under braking and cornering loads, but the rubber bonding degrades with age and cyclic load, allowing the metal sleeve to separate or the rubber to deform beyond its design limit. Once collapsed, the trailing arm can shift fore-aft under braking, causing the rear axle to adopt excessive toe and camber changes dynamically, which manifests as a characteristically unstable rear end under braking — a safety-critical condition. The failure is exacerbated by corroded or seized arm-to-subframe bolts that make replacement more involved.

Symptoms to notice

  • Rear end instability, wandering, or tramping sensation under moderate to firm braking
  • Thudding or knocking from the rear over sharp bumps or when reversing over obstacles

What to check

Visually inspect the large rubber-bonded bush at the forward trailing arm mount for cracking, separation of the rubber from the metal insert, or visible deformation. Check for rear end instability or tramping sensation under firm braking during the test drive. If a workshop inspection is possible: On a hoist, grip the rear trailing arm and attempt fore-aft movement by hand — any perceptible longitudinal movement indicates bush failure or collapse.

Where to look: Rear suspension trailing arm forward mount bushing, inboard attachment point to rear subframe

Ask the seller

  • “Has the rear suspension had any bush or trailing arm work done?”
  • “Does the car feel stable and straight under firm braking?”

03Electric Power Steering Rack Rattle and Knock

The J11 Qashqai uses a column-assist electric power steering (EPS) system where the rack-and-pinion unit is mechanically unassisted.2013–2019Suspension
CommonSuspension $400–$1,800 to fix

Can't confirm for this car

The J11 Qashqai uses a column-assist electric power steering (EPS) system where the rack-and-pinion unit is mechanically unassisted; steering effort is applied by an electric motor on the column. The rack itself uses a spring-loaded anti-lash mechanism to maintain pinion-to-rack mesh. As this preload spring and rack yoke wear, the rack develops internal play, producing a rattle or clonk over road irregularities that is transmitted directly through the steering column to the wheel. Nissan issued a revised rack yoke and preload adjuster specification for this issue; however, worn racks that have progressed beyond the adjustment range require rack replacement.

Symptoms to notice

  • Clonking or rattling noise from the steering rack area over rough roads or expansion joints, felt through the steering wheel
  • Steering wheel shimmy or vibration at highway speeds combined with vague on-centre feel

What to check

  1. Drive slowly over rough surfaces and listen for a clonk or rattle from below the dashboard or front of the vehicle that is synchronised with road irregularities.
  2. With the vehicle stationary and engine running, have an assistant rock the steering wheel rapidly while you feel the intermediate shaft and rack for looseness.
  3. Check for steering wheel vibration or shimmy at highway speed.

Where to look: Steering rack mounted on front subframe behind the engine, connected to column via intermediate shaft

Parts involved: Steering rack.

Ask the seller

  • “Has any steering rack work, adjustment, or replacement been carried out?”
  • “Does the steering rattle or clonk over rough roads or speed bumps?”

04Front Lower Control Arm Ball Joint Failure

Rock each front wheel at the 9 and 3 o'clock positions and at 12 and 6 o'clock to check for play in ball joints and wheel bearings separately.2006–2013Suspension
CommonSuspension $650–$1,800 to fix

Can't confirm for this car

The front lower control arm ball joints on J10 Qashqai models wear faster than expected for vehicle age and mileage in NZ and AU conditions. The ball joint rubber boot perishes, allowing water and road grit ingress that accelerates metal wear inside the socket. Once the joint develops play, the driver experiences clunking over bumps, vague or pulling steering, and uneven tyre wear. On many J10 variants the ball joint is integral to the lower control arm and cannot be replaced independently, requiring full arm replacement. A worn ball joint is a WOF and roadworthy failure item, and at extreme wear can result in joint separation with loss of steering control.

The front wheel of a car splayed outward with the lower control arm hanging down after a ball joint separation.Example of the part — not this vehicle

A separated lower ball joint: the control arm has dropped and the wheel has splayed out under the guard.

Elfix · CC0 · Wikimedia Commons

Symptoms to notice

  • Clunking or knocking noise from front suspension over bumps or during cornering
  • Vague, loose, or pulling steering particularly at low speed
  • Uneven or accelerated front tyre wear on inner or outer edges
  • Vehicle pulling to one side under braking
  • WOF or roadworthy failure for suspension joint play

What to check

  1. Rock each front wheel at the 9 and 3 o'clock positions and at 12 and 6 o'clock to check for play in ball joints and wheel bearings separately.
  2. Inspect for torn or cracked ball joint dust boots.
  3. Have a workshop lift the vehicle and lever the lower control arm to check for ball joint lateral play.

Where to look: Front lower control arm inboard pivot and outboard ball joint, both left and right sides

Parts involved: Ball joint.

Ask the seller

  • “Have the front lower control arm ball joints or arms been replaced?”
  • “Do you hear any clunking noise from the front suspension over bumps?”
  • “When did the vehicle last receive a WOF inspection and did it pass first time?”

05Front Lower Control Arm Ball Joint Wear

Then grip at 6 and 12 o'clock; vertical play at the bottom of the tyre indicates lower ball joint wear.2013–2021Suspension
CommonSuspension $350–$900 to fix

Can't confirm for this car

The front lower control arm on the J11 Qashqai uses a pressed-in ball joint that is not serviceable separately from the arm in most aftermarket configurations. The ball joint socket wears and develops radial play, compromising the precise geometry relationship between the wheel hub, knuckle, and subframe. The resulting looseness creates clunking over bumps and causes the front wheel to adopt unpredictable camber and toe changes during suspension travel, degrading steering precision and accelerating tyre wear. In New Zealand and Australian conditions, road contamination accelerates boot degradation and bearing wear.

The front wheel of a car splayed outward with the lower control arm hanging down after a ball joint separation.Example of the part — not this vehicle

A separated lower ball joint: the control arm has dropped and the wheel has splayed out under the guard.

Elfix · CC0 · Wikimedia Commons

Symptoms to notice

  • Clunking or knocking from front suspension over bumps, speed humps, or when turning at low speed
  • Vague or imprecise steering feel accompanied by uneven or feathered front tyre wear

What to check

Then grip at 6 and 12 o'clock; vertical play at the bottom of the tyre indicates lower ball joint wear. Visually inspect the ball joint rubber boot for cracking or grease loss. Check for clunking over speed humps during the test drive. If a workshop inspection is possible: With the vehicle on a hoist, grip the front tyre at 9 and 3 o'clock and attempt to rock it — lateral play indicates ball joint or tie rod wear.

Where to look: Front suspension lower control arm, inboard pivot to subframe and outboard ball joint to wheel knuckle

Parts involved: Ball joint.

Ask the seller

  • “Has the front suspension had any ball joint or control arm work done?”
  • “Does the car knock or clunk over bumps or when turning slowly?”

06Front and Rear Brake Caliper Guide Pin Seizure

2013–2021Brakes
CommonBrakes $180–$750 to fix

Can't confirm for this car

The J11 Qashqai uses sliding-type brake calipers front and rear, where the caliper body floats on two steel guide pins lubricated with high-temperature grease and protected by rubber boots. In New Zealand and Australian conditions, road salt, water ingress from damaged boots, and extended service intervals allow the guide pins to corrode and seize within their bores. A seized guide pin prevents the caliper from retracting fully after brake application, causing constant pad-to-disc contact, accelerated and uneven pad wear on one side, brake drag, and heat build-up that can warp discs or cause brake fade. The rear calipers on vehicles equipped with integrated electric parking brake mechanisms are particularly susceptible and more expensive to service.

Symptoms to notice

  • Uneven pad wear with inner pad significantly more worn than outer pad, or asymmetric wear between left and right sides
  • Brake drag, pulling to one side under braking, or one wheel noticeably hotter than others after normal driving

What to check

After a test drive, carefully check whether any wheel is significantly hotter than the others — a seized caliper will cause that wheel to be noticeably warm. Inspect caliper guide pin boots for cracking or missing rubber. Remove pads and check for uneven wear (inner pad worn significantly more than outer indicates the guide pins are not allowing the caliper to float). If a workshop inspection is possible: Attempt to slide each caliper by hand after removing the pads — it should move freely with moderate force.

Where to look: Front and rear brake calipers on all four corners; guide pins in caliper bracket bores

Parts involved: Brake disc and pads.

Ask the seller

  • “When were the brakes last serviced and were the caliper guide pins cleaned and greased?”
  • “Does the car pull to one side under braking, or have you noticed uneven pad wear?”

07Brake Caliper Guide Pin Seizure

Check for pulling under braking.2007–2013Brakes
CommonBrakes $150–$500 to fix

Can't confirm for this car

Front brake caliper guide pins seize from corrosion causing uneven pad wear.

Symptoms to notice

  • Vehicle pulling to one side under braking
  • One front disc hotter than the other after use

What to check

  1. Check for pulling under braking.
  2. Feel for uneven wheel heat.
  3. Inspect guide pins.

Where to look: Front brake calipers

Parts involved: Brake disc and pads.

Ask the seller

  • “Has the brake caliper guide pin seizure been inspected or repaired?”

08Rear Suspension Multi-Link Bush Collapse

Inspect rear suspension arm bushes for cracking.2007–2013Suspension
CommonSuspension $400–$1,200 to fix

Can't confirm for this car

Rear multi-link suspension arm bushes harden and collapse causing rear knocking and imprecision.

Symptoms to notice

  • Knocking from rear suspension over rough surfaces
  • Imprecise rear handling feel

What to check

  1. Inspect rear suspension arm bushes for cracking.
  2. Push arms with vehicle raised — any movement indicates worn bushes.

Where to look: Rear multi-link suspension arm bushes

Ask the seller

  • “Has the rear suspension multi-link bush collapse been inspected or repaired?”

09Rear Torsion Beam Axle Bushing Deterioration

Inspect the rubber of each bushing visually for cracking, splitting, or oil contamination.2013–2022Suspension
CommonSuspension $350–$900 to fix

Can't confirm for this car

The J11 Qashqai uses a twist-beam torsion rear axle whose large compliance bushings — where the beam mounts to the body — are made of rubber that hardens and cracks in the New Zealand and Australian climate. Degraded bushings allow the rear axle to shift laterally under load, producing clunking over road imperfections and causing measurable rear axle mis-alignment. This affects tyre wear and directional stability, and the condition is typically missed on a cursory inspection as it requires hands-on physical check of the mounts.

Symptoms to notice

  • Clunking or thudding noise from the rear of the vehicle over bumps or during braking
  • Rear axle wandering feeling on the motorway, requiring constant minor steering corrections
  • Uneven rear tyre wear, often on the inner or outer edges
  • Rear of the vehicle squirming or stepping out on rough road surfaces
  • Visible cracking or perishing of the large cylindrical rubber bushings at the axle mounting points

What to check

  1. Inspect the rubber of each bushing visually for cracking, splitting, or oil contamination.
  2. Check rear tyre inner or outer edge wear which indicates axle misalignment from bushing failure.
  3. If a workshop inspection is possible: With the vehicle on a hoist, physically grasp the rear axle beam and attempt to move it fore-aft and laterally — any movement beyond a few millimetres indicates worn bushings.

Where to look: Rear suspension — torsion beam-to-body mounting points on both left and right sides, visible inside the rear wheel arches

Ask the seller

  • “Has anyone inspected or replaced the rear suspension bushings, and does it have a recent WOF with no advisories?”
  • “Have you noticed any clunking from the rear end over bumps or speed humps?”
  • “Is the rear tyre wear even across both tyres and across the tread face?”

10e-POWER front brake squeal (faulty anti-rattle shims)

Listen for front brake squeal at low speed and while reversing and turning.hybrid2022 onwardBrakes
CommonBrakes $200–$700 to fix

Can't confirm for this car

A high-pitched front brake squeal is a widely reported and Nissan-acknowledged issue on J12 e-POWER cars, made more noticeable because regenerative braking leaves the friction brakes lightly used. Owners describe squealing when reversing and turning, or at low speed, from as little as a few thousand kilometres. Nissan treats it as a known fault and fits a revised front brake shim kit under warranty, though replacement shims have been on back order for extended periods. If left, the original faulty shims can score the discs, turning a cheap fix into a discs-and-pads job.

Symptoms to notice

  • High-pitched squeal from the front brakes, often when reversing or turning
  • Squeal at low speed or when brakes are cold
  • Occasional thud over bumps if shims have moved

What to check

Listen for front brake squeal at low speed and while reversing and turning; inspect the front discs for scoring or a lip, and check service records for a shim kit replacement being fitted or still outstanding on back order.

Where to look: Front brake calipers / pads (anti-rattle shims)

Ask the seller

  • “Have the front brakes ever squealed, and were the revised shims fitted?”
  • “Are the front discs original, or were they replaced due to scoring?”
  • “Is there any outstanding back-ordered brake shim work?”
Fluid leaks1

01MR20DE Front Oil Seal & Cam Cover Gasket Leak

Inspect the front of the engine behind the harmonic balancer for oil seeping from the crankshaft seal.petrol2006–2013Fluid LeaksRead the full fault: symptoms, where to look, what to ask the seller

Nissan Qashqai faults in detail

Each of these has its own page: the symptoms, where to look, what to ask the seller and what the repair costs. Free, no account needed.

1.2 DIG-T Excessive Engine Oil ConsumptionMajor · Engine1.2 DIG-T Timing Chain Guide DisintegrationCritical · Engine1.2 DIG-T Turbo Bearing Failure from Oil CokingCritical · Engine1.6 dCi R9M DPF Clogging on Urban CyclesMajor · Engine12V battery drain when parked (mild-hybrid and e-POWER)Major · Electricale-POWER battery-management software fault (limp mode / loss of drive)Critical · ElectricalJatco RE0F10D CVT Judder and Transmission FailureMajor · TransmissionMR20DD Intake Valve Carbon Deposit BuildupMajor · EngineMR20DD Timing Chain Stretch and Cold-Start RattleMajor · EngineMR20DE Front Oil Seal & Cam Cover Gasket LeakMajor · Fluid LeaksMR20DE Timing Chain Tensioner Cold Start RattleMajor · Engine

What these repairs cost on other cars

Some of the Nissan Qashqai’s documented faults are repairs other models share. Each page lists the documented NZ cost for every model it affects.

Other Nissan models

Nissan Patrol48 documented faultsNissan Navara45 documented faultsNissan X-Trail45 documented faultsNissan Serena27 documented faultsNissan Frontier26 documented faultsNissan Leaf22 documented faults

Nissan Qashqai buyer questions

Is the Nissan Qashqai reliable?

Like any used car, it depends on the specific example and its service history. Across the 28 documented faults for the Nissan Qashqai, the recurring problem areas are engine, body & rust, and suspension. A Nissan Qashqai with a full service history and no signs of the issues listed on this page can be a sound buy but each one needs to be checked individually before you commit.

What are the most common problems with a used Nissan Qashqai?

We've catalogued 28 known faults for the Nissan Qashqai, covering engine, body & rust, and suspension. All 28 are written out in full on this page, with the symptoms to notice, what to inspect, and typical repair costs for each. Free to read, no account needed.

How much do repairs cost on a Nissan Qashqai?

Most single repairs on the Nissan Qashqai fall between $550–$1,800 at NZ independent-workshop rates. Some of the 28 documented faults cost less and a few cost considerably more, and no one car needs them all. Knowing which ones to look for before you view is what lets you negotiate the price down or walk away.

Should I get a pre-purchase inspection on a Nissan Qashqai?

Yes. A Nissan Qashqai inspection focused on its known weak points is the single best way to avoid an expensive mistake. KickTyres gives you a guided, model-specific inspection plus a market valuation and negotiation figure for $24.90 far less than the cost of missing one of the faults on this page.