Nissan2006–2022 Critical issues documented

Nissan Qashqai J10: common faults & what to check

The J10 is the Nissan Qashqai built 2007–2014. It was sold here with the 2.0 petrol. Of the 28 faults documented for the Qashqai, 10 apply to this generation, each with its symptoms, what to inspect and a typical repair cost. Free, no account needed.

Check this exact Nissan Qashqai

Odometer history
Money owing
Reported stolen
Ownership history

Official NZ vehicle register data
NZ owned and operated

Type the plate for the free basics. The full record is a paid check from $13.49, one car at a time, no subscription.

No NZ plate yet, or buying in Australia? Pick the generation and engine and start a free check below. New to KickTyres? How the check works →

Documented faults

Critical

Most serious

$550–$1,800

Typical repair

Systems covered

You're looking at the J10 · 2.0 petrol

Everything below is narrowed to this variant. Pick a different one to change it.

Nissan Qashqai, J10 (2007–2014) (KickTyres illustration)

2007–2014J10 Selected2007–2014J102.0 petrolPetrolDocumented issues10 knownSee faults & what to checkKickTyres illustration, not a photograph.

Choose a different generation

Now narrow it to the engine

A 1.8 and a 2.4 of the same car do not fail the same way, so the faults below narrow to the engine as well as the year. Free, no account needed.

Which engine is in it?

2.0 petrol· 2.0 litre petrol

A 2007 Nissan Qashqai is the J10 generation (2007 to 2014).

Start your free check on this Nissan Qashqai

No plate needed. You get the risk score, the buyer's checklist and the guided inspection for the exact car you picked above — not the whole nameplate.

Nissan Qashqai J10

Can't confirm for this car

Nissan Qashqai · 2007

Narrowed to the year. No engine is recorded for this vehicle. Pick an engine to see which faults apply.

Tell us the engine, or check the engine code on the car, before relying on this.

No engine is recorded for this vehicle.

matched on year only

What to look out for

The checks worth doing on a Nissan Qashqai before you hand over any money. Every documented fault is listed below, each with its own page.

Serious issue
Probe suspect areas with a pick or screwdriver to check for soft or hollow metal.
See why
Rear Subframe Corrosion at Mounting Points
The rear subframe on J10 Qashqai models is susceptible to corrosion at its unibody mounting points, particularly in the coastal and high-rainfall environments common across NZ and AU. Road salt, mud trapped around the mounting brackets, and inadequate factory undercoating allow rust to penetrate the subframe steel and the surrounding body mounting pockets. In advanced cases the mounting bolt holes corrode through, causing subframe movement that manifests as rear-end rattles and imprecise handling. Structurally compromised mounting points represent a serious safety hazard and result in WOF or roadworthy rejection. Repair requires specialist rust treatment, plate welding, or full subframe replacement in severe cases.
What you would notice
- Rattling or clunking from rear of vehicle over rough road surfaces
- Imprecise or wandering rear-end handling at highway speed
- Visible rust, bubbling paint, or scaling metal under the rear of the vehicle
- WOF or roadworthy rejection for structural corrosion at subframe mounts
Typically $1,600–$6,000 to put right.
Costly issue
Rock each front wheel at the 9 and 3 o'clock positions and at 12 and 6 o'clock to check for play in ball joints and wheel bearings separately.
See why
Front Lower Control Arm Ball Joint Failure
The front lower control arm ball joints on J10 Qashqai models wear faster than expected for vehicle age and mileage in NZ and AU conditions. The ball joint rubber boot perishes, allowing water and road grit ingress that accelerates metal wear inside the socket. Once the joint develops play, the driver experiences clunking over bumps, vague or pulling steering, and uneven tyre wear. On many J10 variants the ball joint is integral to the lower control arm and cannot be replaced independently, requiring full arm replacement. A worn ball joint is a WOF and roadworthy failure item, and at extreme wear can result in joint separation with loss of steering control.
What you would notice
- Clunking or knocking noise from front suspension over bumps or during cornering
- Vague, loose, or pulling steering particularly at low speed
- Uneven or accelerated front tyre wear on inner or outer edges
- Vehicle pulling to one side under braking
- WOF or roadworthy failure for suspension joint play
Typically $650–$1,800 to put right.
Costly issue
Check for pulling under braking.
See why
Brake Caliper Guide Pin Seizure
Front brake caliper guide pins seize from corrosion causing uneven pad wear.
What you would notice
- Vehicle pulling to one side under braking
- One front disc hotter than the other after use
Typically $150–$500 to put right.
Costly issue
Scan for EPS fault codes.
See why
Electric Power Steering Failure
EPS system can develop a fault causing loss of power assistance.
What you would notice
- Sudden loss of power steering assistance with EPS warning light
- Heavy steering especially at low speeds and during parking
Typically $600–$2,200 to put right.
Common issue
Test AC during test drive.
See why
Air Conditioning Compressor Clutch Failure
AC compressor clutch bearing wears causing squealing when AC is engaged.
What you would notice
- Squealing from engine front when AC is switched on
- Noise stops when AC is switched off
Typically $400–$1,500 to put right.
Common issue
Inspect rear suspension arm bushes for cracking.
See why
Rear Suspension Multi-Link Bush Collapse
Rear multi-link suspension arm bushes harden and collapse causing rear knocking and imprecision.
What you would notice
- Knocking from rear suspension over rough surfaces
- Imprecise rear handling feel
Typically $400–$1,200 to put right.

See all 10 issues for this oneDocumented for the exact year and engine you picked, including 1 rated critical.

Electrical2

01Electric Power Steering Failure

Scan for EPS fault codes.2007–2013Electrical$600–$2,200

OccasionalElectrical $600–$2,200 to fix

EPS system can develop a fault causing loss of power assistance.

Symptoms to notice

Sudden loss of power steering assistance with EPS warning light
Heavy steering especially at low speeds and during parking

What to check

Scan for EPS fault codes.
Test steering — any heavy or inconsistent feel indicates EPS fault.

Where to look: EPS rack and column assembly

Parts involved: Steering rack.

Ask the seller

“Has the electric power steering failure been inspected or repaired?”

02Air Conditioning Compressor Clutch Failure

Test AC during test drive.2007–2013Electrical$400–$1,500

CommonElectrical $400–$1,500 to fix

AC compressor clutch bearing wears causing squealing when AC is engaged.

Symptoms to notice

Squealing from engine front when AC is switched on
Noise stops when AC is switched off

What to check

Test AC during test drive.
Listen for squealing from engine front when AC is engaged.

Where to look: AC compressor on front of engine

Parts involved: Clutch.

Ask the seller

“Has the air conditioning compressor clutch failure been inspected or repaired?”

Body, brakes, suspension & interior1 critical4

03Rear Subframe Corrosion at Mounting Points

Probe suspect areas with a pick or screwdriver to check for soft or hollow metal.2006–2013Body & Rust$1,600–$6,000

OccasionalBody & Rust $1,600–$6,000 to fix

The rear subframe on J10 Qashqai models is susceptible to corrosion at its unibody mounting points, particularly in the coastal and high-rainfall environments common across NZ and AU. Road salt, mud trapped around the mounting brackets, and inadequate factory undercoating allow rust to penetrate the subframe steel and the surrounding body mounting pockets. In advanced cases the mounting bolt holes corrode through, causing subframe movement that manifests as rear-end rattles and imprecise handling. Structurally compromised mounting points represent a serious safety hazard and result in WOF or roadworthy rejection. Repair requires specialist rust treatment, plate welding, or full subframe replacement in severe cases.

Symptoms to notice

Rattling or clunking from rear of vehicle over rough road surfaces
Imprecise or wandering rear-end handling at highway speed
Visible rust, bubbling paint, or scaling metal under the rear of the vehicle
WOF or roadworthy rejection for structural corrosion at subframe mounts

What to check

Probe suspect areas with a pick or screwdriver to check for soft or hollow metal.
Check inner wheel arches for corrosion bubbling from behind the inner liner.
If a workshop inspection is possible: With the vehicle on a hoist inspect all four rear subframe mounting points and the surrounding unibody metal for rust perforation, bubbling paint, or movement under load.

Where to look: Rear underside of vehicle at the four subframe-to-unibody mounting brackets

Parts involved: Chassis and structural rust, Body corrosion.

Ask the seller

“Has the vehicle ever been undercoated or received rust-proofing treatment?”
“Has it been used near the coast or regularly on unsealed gravel roads?”
“Do you notice any rattles or clunks from the rear end over rough surfaces?”

04Front Lower Control Arm Ball Joint Failure

Rock each front wheel at the 9 and 3 o'clock positions and at 12 and 6 o'clock to check for play in ball joints and wheel bearings separately.2006–2013Suspension$650–$1,800

CommonSuspension $650–$1,800 to fix

The front lower control arm ball joints on J10 Qashqai models wear faster than expected for vehicle age and mileage in NZ and AU conditions. The ball joint rubber boot perishes, allowing water and road grit ingress that accelerates metal wear inside the socket. Once the joint develops play, the driver experiences clunking over bumps, vague or pulling steering, and uneven tyre wear. On many J10 variants the ball joint is integral to the lower control arm and cannot be replaced independently, requiring full arm replacement. A worn ball joint is a WOF and roadworthy failure item, and at extreme wear can result in joint separation with loss of steering control.

Symptoms to notice

Clunking or knocking noise from front suspension over bumps or during cornering
Vague, loose, or pulling steering particularly at low speed
Uneven or accelerated front tyre wear on inner or outer edges
Vehicle pulling to one side under braking
WOF or roadworthy failure for suspension joint play

What to check

Rock each front wheel at the 9 and 3 o'clock positions and at 12 and 6 o'clock to check for play in ball joints and wheel bearings separately.
Inspect for torn or cracked ball joint dust boots.
Have a workshop lift the vehicle and lever the lower control arm to check for ball joint lateral play.

Where to look: Front lower control arm inboard pivot and outboard ball joint, both left and right sides

Parts involved: Ball joint.

Ask the seller

“Have the front lower control arm ball joints or arms been replaced?”
“Do you hear any clunking noise from the front suspension over bumps?”
“When did the vehicle last receive a WOF inspection and did it pass first time?”

05Brake Caliper Guide Pin Seizure

Check for pulling under braking.2007–2013Brakes$150–$500

CommonBrakes $150–$500 to fix

Front brake caliper guide pins seize from corrosion causing uneven pad wear.

Symptoms to notice

Vehicle pulling to one side under braking
One front disc hotter than the other after use

What to check

Check for pulling under braking.
Feel for uneven wheel heat.
Inspect guide pins.

Where to look: Front brake calipers

Parts involved: Brake disc and pads.

Ask the seller

“Has the brake caliper guide pin seizure been inspected or repaired?”

06Rear Suspension Multi-Link Bush Collapse

Inspect rear suspension arm bushes for cracking.2007–2013Suspension$400–$1,200

CommonSuspension $400–$1,200 to fix

Rear multi-link suspension arm bushes harden and collapse causing rear knocking and imprecision.

Symptoms to notice

Knocking from rear suspension over rough surfaces
Imprecise rear handling feel

What to check

Inspect rear suspension arm bushes for cracking.
Push arms with vehicle raised — any movement indicates worn bushes.

Where to look: Rear multi-link suspension arm bushes

Ask the seller

“Has the rear suspension multi-link bush collapse been inspected or repaired?”

Depends on the exact engine — 4 moreDocumented for a specific engine we could not confirm from what you picked. Check the engine code on the car.

Engine, transmission & cooling3

01Haldex Rear AWD Coupling Failure from Fluid Neglect

On AWD variants, check whether Haldex fluid service is recorded in the service book.petrol2006–2013TransmissionCan't confirm for this car$1,200–$3,500

OccasionalTransmission $1,200–$3,500 to fix

Can't confirm for this car

AWD J10 Qashqais use a Haldex rear coupling to engage rear-wheel drive. The unit has its own fluid reservoir that requires periodic replacement (every 40,000 km). Neglected fluid causes internal clutch pack wear; severely degraded fluid leads to coupling seizure. A seized coupling either fails to engage the rear wheels (understeer on loose surfaces) or locks permanently (binding and shudder in tight cornering). Replacement of the complete unit is typically required.

Symptoms to notice

Binding, vibration, or shudder when turning tightly at low speed (seized coupling)
Loss of rear traction on gravel or wet roads (failed-open coupling)
Burning smell from rear drivetrain under load
AWD system warning light

What to check

On AWD variants, check whether Haldex fluid service is recorded in the service book.
Drive in a tight circle on a hard surface at low speed – any binding or shudder indicates coupling problems.
Ask specifically about off-road use or mud exposure, which contaminate the coupling fluid faster.

Where to look: Rear drivetrain – Haldex AWD coupling unit on the propshaft or at the rear differential

Parts involved: Clutch.

Ask the seller

“Has the Haldex coupling fluid been serviced and at what intervals?”
“Is this an AWD or 2WD variant?”
“Has any binding or shudder been noticed when parking or cornering?”

02MR20DE Timing Chain Tensioner Cold Start Rattle

Start the engine cold and immediately listen for a metallic rattle from the timing chain cover at the front of the engine.petrol2006–2013EngineCan't confirm for this car$900–$2,500Read the full fault: symptoms, where to look, what to ask the seller

03CVT Belt Slip and Judder Under Load

Test drive under full acceleration from low speed on a hill or on-ramp.petrol2006–2013TransmissionCan't confirm for this car$3,800–$9,500

CommonTransmission $3,800–$9,500 to fix

Can't confirm for this car

The Jatco RE0F10A (J10) and RE0F10D (J11) continuously variable transmissions are prone to steel push-belt and pulley slip causing a pronounced shudder or judder under moderate to heavy acceleration, particularly when pulling away from low speeds or climbing inclines. Worn belt and pulley surfaces cause slippage that the TCM misidentifies as normal operation until driveability becomes noticeably impaired. Fluid degradation accelerates wear; Nissan NS-2 CVT fluid changes at or before 60,000 km are essential. Full rebuild or replacement is the only lasting fix once slip begins and internal damage has occurred.

Symptoms to notice

Shudder or judder felt through the drivetrain and floor under acceleration
Hesitation or flaring of engine revs without corresponding acceleration
Delayed engagement when selecting Drive or Reverse from Park
Burning or overheated transmission smell after hill driving
CVT warning light or transmission temperature warning in instrument cluster

What to check

Test drive under full acceleration from low speed on a hill or on-ramp.
Check for shudder, slip, or rev flare.
Inspect CVT fluid colour via dipstick or fill plug — it should be red or pink, not brown or burnt-smelling.
Request documented CVT fluid change history.

Where to look: Transmission casing in the engine bay and transmission tunnel beneath the vehicle

Parts involved: CVT belt and pulleys.

Ask the seller

“Has the CVT fluid ever been changed and at what mileage?”
“Has the transmission been serviced, rebuilt, or replaced?”
“Do you notice any judder, shudder, or hesitation when accelerating?”

Fluid leaks1

01MR20DE Front Oil Seal & Cam Cover Gasket Leak

Inspect the front of the engine behind the harmonic balancer for oil seeping from the crankshaft seal.petrol2006–2013Fluid LeaksCan't confirm for this car$450–$1,400Read the full fault: symptoms, where to look, what to ask the seller

Other Nissan Qashqai engines and years18 documented issues that do not apply to the one you picked.

Engine, transmission & cooling10

06All-Mode 4WD Rear Coupling Unit Shudder and Seizure

With the vehicle in Auto 4WD mode, drive slowly through several tight full-lock turns in a car park.petrol2014–2021TransmissionDoes not apply$1,500–$4,000

OccasionalTransmission $1,500–$4,000 to fix

Does not apply

The electronically controlled rear coupling unit on 4WD Qashqai models (supplied by BorgWarner) transfers torque to the rear wheels via an electro-hydraulic clutch pack. The coupling's internal fluid degrades and the multi-plate clutch pack wears, producing a pronounced shudder or vibration when cornering at low speed or when the 4WD system engages under load. In cases where the unit has seized or the coupling ECU has failed, the vehicle may pull or crab-walk on tight turns, causing serious tyre scrub and drivetrain stress.

Symptoms to notice

Juddering or vibration through the floor and steering wheel during slow tight turns in 4WD Auto mode
Clunking sound when the 4WD system engages from 2WD mode
4WD warning light or ALL MODE 4x4 system fault on the instrument cluster
Abnormal tyre wear on all four corners due to drivetrain binding
Vehicle pulling or resisting during sharp parking manoeuvres

What to check

With the vehicle in Auto 4WD mode, drive slowly through several tight full-lock turns in a car park. Any shudder, vibration, or binding sensation through the steering or floor indicates coupling wear. Check for fault codes in the 4WD control module. Inspect the coupling unit casing under the rear of the vehicle for fluid leaks or heat discolouration.

Where to look: Rear axle assembly, coupling unit mounted ahead of the rear differential between the propeller shaft and rear axle

Parts involved: Clutch.

Ask the seller

“Has the rear coupling unit fluid ever been replaced, or has the coupling itself been replaced?”
“Have you noticed any shudder or vibration when making tight turns in car parks, especially in 4WD mode?”
“Has any 4WD warning light or drivetrain fault code appeared on the dashboard?”

071.6 dCi R9M DPF Clogging on Urban Cycles

Connect an OBD2 scanner and check for DPF soot loading percentage and any related fault codes.diesel2013–2021EngineDoes not apply$550–$3,200Read the full fault: symptoms, where to look, what to ask the seller

08HR16DE Timing Chain Tensioner Rattle on Cold Start

Cold-start the engine and listen for a metallic chain rattle from the front of the engine lasting more than 2–3 seconds.petrol2013–2019EngineDoes not apply$900–$2,200

CommonEngine $900–$2,200 to fix

Does not apply

The HR16DE 1.6-litre engine uses a hydraulic timing chain tensioner that relies on oil pressure to maintain chain tension. On cold starts the tensioner bleeds down overnight, and during the critical seconds before oil pressure builds the chain slaps against the guide rails, producing a characteristic metallic rattle from the front of the engine. Repeated episodes accelerate guide rail and chain wear; in neglected cases the chain stretches beyond the tensioner's range, causing variable camshaft timing errors, rough running, and ultimately chain skip or breakage.

Symptoms to notice

Metallic rattling noise from front of engine on cold start, typically lasting 2–10 seconds before quietening
Camshaft timing fault codes (P0011, P0014, P0340) stored in ECU, often accompanied by rough idle after cold start

What to check

Cold-start the engine and listen for a metallic chain rattle from the front of the engine lasting more than 2–3 seconds. Check for camshaft position/crankshaft correlation fault codes (P0011, P0014, P0340). Inspect oil level and condition; low or degraded oil worsens bleed-down. If rattle persists beyond 5 seconds on cold start, the tensioner and guide rails should be inspected.

Where to look: Front of engine block, timing cover side — accessible after removing cam cover and timing cover

Parts involved: Timing chain.

Ask the seller

“Does the engine rattle on cold start before settling down?”
“Has the timing chain tensioner or chain ever been replaced or inspected?”

09MR20DD Intake Valve Carbon Deposit Buildup

Remove intake manifold and inspect valve backs with a bore scope or direct light; look for thick carbon crust on valve stems and port walls.petrol2014–2021EngineDoes not apply$600–$1,400Read the full fault: symptoms, where to look, what to ask the seller

10MR20DD Engine Coolant Thermostat Housing Leak

petrol2013–2019CoolingDoes not apply$300–$750

OccasionalCooling $300–$750 to fix

Does not apply

The MR20DD engine uses a plastic thermostat housing integrated with the coolant outlet that is prone to cracking at the sealing surface or at the housing body as the plastic ages and heat cycles. Coolant leaks from this housing can drip onto the exhaust manifold causing steam and burning smell, and if undetected lead to low coolant levels and overheating. The housing is located in a partially obscured position that makes small weeps easy to miss during a casual inspection.

An annotated photograph of an automotive engine thermostat identifying the wax capsule and both disc valves. — A double-valve engine thermostat, labelled: the wax capsule is what sticks.
Dougsim · CC BY-SA 3.0 · Wikimedia Commons

Symptoms to notice

White or rusty coolant staining or dried residue on or below the thermostat housing
Coolant level dropping in the reservoir between top-ups without evidence of internal consumption
Sweet antifreeze smell inside the cabin or from the engine bay after a run
Steam visible from the engine bay when the vehicle is warm and parked
Overheating warning if the leak is substantial and coolant level drops below the minimum

What to check

With the engine cold, inspect the thermostat housing and all coolant hose connections at the front and rear of the engine for white mineral deposits, dried coolant residue, or active weeping. Check the coolant reservoir level. After a test drive, re-inspect the housing area for steam or fresh coolant residue. If a workshop inspection is possible: Pressure-test the cooling system if any doubt exists.

Where to look: Front of the MR20DD engine, thermostat housing on the upper coolant outlet pipe near the radiator top hose connection

Parts involved: Thermostat.

Ask the seller

“Has the thermostat or thermostat housing ever been replaced, or has there been any coolant leak in the engine bay?”
“Has the coolant level ever dropped unexpectedly, and when was the coolant last changed?”
“Has the vehicle ever overheated or shown a high temperature warning?”

Electrical2

01e-POWER battery-management software fault (limp mode / loss of drive)

Check the vehicle's recall history for KBA 14969R / R24C8 (AU REC-006324) and confirm the BMS software update has been applied.hybrid2022 onwardElectricalDoes not apply$0–$300Read the full fault: symptoms, where to look, what to ask the seller

0212V battery drain when parked (mild-hybrid and e-POWER)

Ask how long the car can sit before it fails to start and whether it has needed jump-starts.2022 onwardElectricalDoes not apply$300–$900Read the full fault: symptoms, where to look, what to ask the seller

Body, brakes, suspension & interior6

01Rear Trailing Arm Bush Collapse

The J11 Qashqai rear multi-link suspension uses large hydraulic or rubber-bonded bushes in the trailing arm mounts.2014–2021SuspensionDoes not apply$500–$1,400

OccasionalSuspension $500–$1,400 to fix

Does not apply

The J11 Qashqai rear multi-link suspension uses large hydraulic or rubber-bonded bushes in the trailing arm mounts. These bushes are designed to allow controlled compliance under braking and cornering loads, but the rubber bonding degrades with age and cyclic load, allowing the metal sleeve to separate or the rubber to deform beyond its design limit. Once collapsed, the trailing arm can shift fore-aft under braking, causing the rear axle to adopt excessive toe and camber changes dynamically, which manifests as a characteristically unstable rear end under braking — a safety-critical condition. The failure is exacerbated by corroded or seized arm-to-subframe bolts that make replacement more involved.

Symptoms to notice

Rear end instability, wandering, or tramping sensation under moderate to firm braking
Thudding or knocking from the rear over sharp bumps or when reversing over obstacles

What to check

Visually inspect the large rubber-bonded bush at the forward trailing arm mount for cracking, separation of the rubber from the metal insert, or visible deformation. Check for rear end instability or tramping sensation under firm braking during the test drive. If a workshop inspection is possible: On a hoist, grip the rear trailing arm and attempt fore-aft movement by hand — any perceptible longitudinal movement indicates bush failure or collapse.

Where to look: Rear suspension trailing arm forward mount bushing, inboard attachment point to rear subframe

Ask the seller

“Has the rear suspension had any bush or trailing arm work done?”
“Does the car feel stable and straight under firm braking?”

02Electric Power Steering Rack Rattle and Knock

The J11 Qashqai uses a column-assist electric power steering (EPS) system where the rack-and-pinion unit is mechanically unassisted.2013–2019SuspensionDoes not apply$400–$1,800

CommonSuspension $400–$1,800 to fix

Does not apply

The J11 Qashqai uses a column-assist electric power steering (EPS) system where the rack-and-pinion unit is mechanically unassisted; steering effort is applied by an electric motor on the column. The rack itself uses a spring-loaded anti-lash mechanism to maintain pinion-to-rack mesh. As this preload spring and rack yoke wear, the rack develops internal play, producing a rattle or clonk over road irregularities that is transmitted directly through the steering column to the wheel. Nissan issued a revised rack yoke and preload adjuster specification for this issue; however, worn racks that have progressed beyond the adjustment range require rack replacement.

Symptoms to notice

Clonking or rattling noise from the steering rack area over rough roads or expansion joints, felt through the steering wheel
Steering wheel shimmy or vibration at highway speeds combined with vague on-centre feel

What to check

Drive slowly over rough surfaces and listen for a clonk or rattle from below the dashboard or front of the vehicle that is synchronised with road irregularities.
With the vehicle stationary and engine running, have an assistant rock the steering wheel rapidly while you feel the intermediate shaft and rack for looseness.
Check for steering wheel vibration or shimmy at highway speed.

Where to look: Steering rack mounted on front subframe behind the engine, connected to column via intermediate shaft

Parts involved: Steering rack.

Ask the seller

“Has any steering rack work, adjustment, or replacement been carried out?”
“Does the steering rattle or clonk over rough roads or speed bumps?”

03Front Lower Control Arm Ball Joint Wear

Then grip at 6 and 12 o'clock; vertical play at the bottom of the tyre indicates lower ball joint wear.2013–2021SuspensionDoes not apply$350–$900

CommonSuspension $350–$900 to fix

Does not apply

The front lower control arm on the J11 Qashqai uses a pressed-in ball joint that is not serviceable separately from the arm in most aftermarket configurations. The ball joint socket wears and develops radial play, compromising the precise geometry relationship between the wheel hub, knuckle, and subframe. The resulting looseness creates clunking over bumps and causes the front wheel to adopt unpredictable camber and toe changes during suspension travel, degrading steering precision and accelerating tyre wear. In New Zealand and Australian conditions, road contamination accelerates boot degradation and bearing wear.

Symptoms to notice

Clunking or knocking from front suspension over bumps, speed humps, or when turning at low speed
Vague or imprecise steering feel accompanied by uneven or feathered front tyre wear

What to check

Then grip at 6 and 12 o'clock; vertical play at the bottom of the tyre indicates lower ball joint wear. Visually inspect the ball joint rubber boot for cracking or grease loss. Check for clunking over speed humps during the test drive. If a workshop inspection is possible: With the vehicle on a hoist, grip the front tyre at 9 and 3 o'clock and attempt to rock it — lateral play indicates ball joint or tie rod wear.

Where to look: Front suspension lower control arm, inboard pivot to subframe and outboard ball joint to wheel knuckle

Parts involved: Ball joint.

Ask the seller

“Has the front suspension had any ball joint or control arm work done?”
“Does the car knock or clunk over bumps or when turning slowly?”

04Front and Rear Brake Caliper Guide Pin Seizure

2013–2021BrakesDoes not apply$180–$750

CommonBrakes $180–$750 to fix

Does not apply

The J11 Qashqai uses sliding-type brake calipers front and rear, where the caliper body floats on two steel guide pins lubricated with high-temperature grease and protected by rubber boots. In New Zealand and Australian conditions, road salt, water ingress from damaged boots, and extended service intervals allow the guide pins to corrode and seize within their bores. A seized guide pin prevents the caliper from retracting fully after brake application, causing constant pad-to-disc contact, accelerated and uneven pad wear on one side, brake drag, and heat build-up that can warp discs or cause brake fade. The rear calipers on vehicles equipped with integrated electric parking brake mechanisms are particularly susceptible and more expensive to service.

Symptoms to notice

Uneven pad wear with inner pad significantly more worn than outer pad, or asymmetric wear between left and right sides
Brake drag, pulling to one side under braking, or one wheel noticeably hotter than others after normal driving

What to check

After a test drive, carefully check whether any wheel is significantly hotter than the others — a seized caliper will cause that wheel to be noticeably warm. Inspect caliper guide pin boots for cracking or missing rubber. Remove pads and check for uneven wear (inner pad worn significantly more than outer indicates the guide pins are not allowing the caliper to float). If a workshop inspection is possible: Attempt to slide each caliper by hand after removing the pads — it should move freely with moderate force.

Where to look: Front and rear brake calipers on all four corners; guide pins in caliper bracket bores

Parts involved: Brake disc and pads.

Ask the seller

“When were the brakes last serviced and were the caliper guide pins cleaned and greased?”
“Does the car pull to one side under braking, or have you noticed uneven pad wear?”

05Rear Torsion Beam Axle Bushing Deterioration

Inspect the rubber of each bushing visually for cracking, splitting, or oil contamination.2013–2022SuspensionDoes not apply$350–$900

CommonSuspension $350–$900 to fix

Does not apply

The J11 Qashqai uses a twist-beam torsion rear axle whose large compliance bushings — where the beam mounts to the body — are made of rubber that hardens and cracks in the New Zealand and Australian climate. Degraded bushings allow the rear axle to shift laterally under load, producing clunking over road imperfections and causing measurable rear axle mis-alignment. This affects tyre wear and directional stability, and the condition is typically missed on a cursory inspection as it requires hands-on physical check of the mounts.

Symptoms to notice

Clunking or thudding noise from the rear of the vehicle over bumps or during braking
Rear axle wandering feeling on the motorway, requiring constant minor steering corrections
Uneven rear tyre wear, often on the inner or outer edges
Rear of the vehicle squirming or stepping out on rough road surfaces
Visible cracking or perishing of the large cylindrical rubber bushings at the axle mounting points

What to check

Inspect the rubber of each bushing visually for cracking, splitting, or oil contamination.
Check rear tyre inner or outer edge wear which indicates axle misalignment from bushing failure.
If a workshop inspection is possible: With the vehicle on a hoist, physically grasp the rear axle beam and attempt to move it fore-aft and laterally — any movement beyond a few millimetres indicates worn bushings.

Where to look: Rear suspension — torsion beam-to-body mounting points on both left and right sides, visible inside the rear wheel arches

Ask the seller

“Has anyone inspected or replaced the rear suspension bushings, and does it have a recent WOF with no advisories?”
“Have you noticed any clunking from the rear end over bumps or speed humps?”
“Is the rear tyre wear even across both tyres and across the tread face?”

06e-POWER front brake squeal (faulty anti-rattle shims)

Listen for front brake squeal at low speed and while reversing and turning.hybrid2022 onwardBrakesDoes not apply$200–$700

CommonBrakes $200–$700 to fix

Does not apply

A high-pitched front brake squeal is a widely reported and Nissan-acknowledged issue on J12 e-POWER cars, made more noticeable because regenerative braking leaves the friction brakes lightly used. Owners describe squealing when reversing and turning, or at low speed, from as little as a few thousand kilometres. Nissan treats it as a known fault and fits a revised front brake shim kit under warranty, though replacement shims have been on back order for extended periods. If left, the original faulty shims can score the discs, turning a cheap fix into a discs-and-pads job.

Symptoms to notice

High-pitched squeal from the front brakes, often when reversing or turning
Squeal at low speed or when brakes are cold
Occasional thud over bumps if shims have moved

What to check

Listen for front brake squeal at low speed and while reversing and turning; inspect the front discs for scoring or a lip, and check service records for a shim kit replacement being fitted or still outstanding on back order.

Where to look: Front brake calipers / pads (anti-rattle shims)

Ask the seller

“Have the front brakes ever squealed, and were the revised shims fitted?”
“Are the front discs original, or were they replaced due to scoring?”
“Is there any outstanding back-ordered brake shim work?”

Nissan Qashqai faults in detail

Narrowed to the Nissan Qashqai · 2007. Each of these has its own page: the symptoms, where to look, what to ask the seller and what the repair costs. Free, no account needed.

MR20DE Front Oil Seal & Cam Cover Gasket LeakMajor · Fluid Leaks MR20DE Timing Chain Tensioner Cold Start RattleMajor · Engine

What these repairs cost on other cars

Some of the Nissan Qashqai’s documented faults are repairs other models share. Each page lists the documented NZ cost for every model it affects.

Other Nissan models

Nissan Patrol48 documented faults Nissan Navara45 documented faults Nissan X-Trail45 documented faults Nissan Serena27 documented faults Nissan Frontier26 documented faults Nissan Leaf22 documented faults

Nissan Qashqai buyer questions

Is the Nissan Qashqai reliable?

Like any used car, it depends on the specific example and its service history. Across the 28 documented faults for the Nissan Qashqai, the recurring problem areas are engine, body & rust, and suspension. A Nissan Qashqai with a full service history and no signs of the issues listed on this page can be a sound buy but each one needs to be checked individually before you commit.

What are the most common problems with a used Nissan Qashqai?

We've catalogued 28 known faults for the Nissan Qashqai, covering engine, body & rust, and suspension. All 28 are written out in full on this page, with the symptoms to notice, what to inspect, and typical repair costs for each. Free to read, no account needed.

How much do repairs cost on a Nissan Qashqai?

Most single repairs on the Nissan Qashqai fall between $550–$1,800 at NZ independent-workshop rates. Some of the 28 documented faults cost less and a few cost considerably more, and no one car needs them all. Knowing which ones to look for before you view is what lets you negotiate the price down or walk away.

Should I get a pre-purchase inspection on a Nissan Qashqai?

Yes. A Nissan Qashqai inspection focused on its known weak points is the single best way to avoid an expensive mistake. KickTyres gives you a guided, model-specific inspection plus a market valuation and negotiation figure for $24.90 far less than the cost of missing one of the faults on this page.

Check this exact Nissan Qashqai

You're looking at the J10 · 2.0 petrol

Now narrow it to the engine

Start your free check on this Nissan Qashqai

What to look out for

01Electric Power Steering Failure

02Air Conditioning Compressor Clutch Failure

03Rear Subframe Corrosion at Mounting Points

04Front Lower Control Arm Ball Joint Failure

05Brake Caliper Guide Pin Seizure

06Rear Suspension Multi-Link Bush Collapse

01Haldex Rear AWD Coupling Failure from Fluid Neglect

02MR20DE Timing Chain Tensioner Cold Start Rattle

03CVT Belt Slip and Judder Under Load

01MR20DE Front Oil Seal & Cam Cover Gasket Leak

011.2 DIG-T Timing Chain Guide Disintegration

021.2 DIG-T Turbo Bearing Failure from Oil Coking

03Jatco RE0F10D CVT Judder and Transmission Failure

04MR20DD Timing Chain Stretch and Cold-Start Rattle

051.2 DIG-T Excessive Engine Oil Consumption

06All-Mode 4WD Rear Coupling Unit Shudder and Seizure

071.6 dCi R9M DPF Clogging on Urban Cycles

08HR16DE Timing Chain Tensioner Rattle on Cold Start

09MR20DD Intake Valve Carbon Deposit Buildup

10MR20DD Engine Coolant Thermostat Housing Leak

01e-POWER battery-management software fault (limp mode / loss of drive)

0212V battery drain when parked (mild-hybrid and e-POWER)

01Rear Trailing Arm Bush Collapse

02Electric Power Steering Rack Rattle and Knock

03Front Lower Control Arm Ball Joint Wear

04Front and Rear Brake Caliper Guide Pin Seizure

05Rear Torsion Beam Axle Bushing Deterioration

06e-POWER front brake squeal (faulty anti-rattle shims)

Nissan Qashqai faults in detail

What these repairs cost on other cars

Other Nissan models

Nissan Qashqai buyer questions

Is the Nissan Qashqai reliable?

What are the most common problems with a used Nissan Qashqai?

How much do repairs cost on a Nissan Qashqai?

Should I get a pre-purchase inspection on a Nissan Qashqai?