Skip to content
KickTyres
Ford2015–2025 Critical issues documented

Ford Everest U704: common faults & what to check

The U704 is the Ford Everest built 2022 onward. It was sold here with the 2.0 twin-turbo diesel and 3.0 V6 turbo-diesel. Of the 16 faults documented for the Everest, 5 apply to this generation, each with its symptoms, what to inspect and a typical repair cost. Free, no account needed.

Check this exact Ford Everest

  • Odometer history
  • Money owing
  • Reported stolen
  • Ownership history
  • Official NZ vehicle register data
  • NZ owned and operated

Type the plate for the free basics. The full record is a paid check from $13.49, one car at a time, no subscription.

No NZ plate yet, or buying in Australia? Pick the generation and engine and start a free check below. New to KickTyres? How the check works →

16

Documented faults

Critical

Most serious

$650–$4,500

Typical repair

19

Service milestones

You're looking at the U704

2 engine variants are documented for this generation. Pick yours to narrow further, or keep reading for the generation as a whole.

Choose a different generation

Now narrow it to the engine

A 1.8 and a 2.4 of the same car do not fail the same way, so the faults below narrow to the engine as well as the year. Free, no account needed.

A 2023 Ford Everest is the U704 generation (2022 to now).

Start your free check on this Ford Everest

No plate needed. You get the risk score, the buyer's checklist and the guided inspection for the exact car you picked above — not the whole nameplate.

Ford Everest U704Engine not picked yet

Pick the engine above first: the Everest came with 2, and without it the report has to show all of their faults. Pick the engine

Free. The paid plate check is separate, and stays optional.

Can't confirm for this car

Ford Everest · 2023

Narrowed to the year. No engine is recorded for this vehicle. Pick an engine to see which faults apply.

Tell us the engine, or check the engine code on the car, before relying on this.

  • No engine is recorded for this vehicle.

matched on year only

What to look out for

The checks worth doing on a Ford Everest before you hand over any money. Every documented fault is listed below, each with its own page.

  • Common issue

    Sit in the car and work the screen hard — cameras, CarPlay/Android Auto, climate controls — for several minutes and watch for lag or reboots.

    See why

    SYNC4 infotainment glitches and 12V battery drain (Next-Gen)

    Early Next-Gen Everests have a well-documented pattern of electrical gremlins: the large SYNC4 portrait screen freezing, rebooting or losing camera feeds, phantom warning messages, and flat 12V batteries caused by modules failing to sleep. Most issues are fixed under warranty with software updates and battery replacement, but they are annoying and a flat battery can leave you stranded. Check whether outstanding software updates have been applied.

    What you would notice

    • Touchscreen freezes, black screen or spontaneous reboots
    • Reversing camera feed missing or lagging
    • Flat 12V battery after the car sits a few days
    • Random warning chimes/messages that clear themselves

    Typically $250–$1,200 to put right.

Ford Everest service schedule

The 2 engines a 2023 Ford Everest was sold with, each with its own intervals. Pick your engine above to narrow this to one. These are the model’s intervals — the car’s own service book is the only thing that can tell you what has actually been done to it.

Fourth Generation · 2022–2026 · 2.0L Bi-Turbo Diesel - 4WD (Trend/Sport)

Diesel

Due by distance

  1. 60,000 km

    Check suspension bushings and shock absorber performance.

  2. 100,000 km

    Review the timing belt/chain components and cooling system hoses.

  3. 150,000 km

    Marks the first major fuel filter and air filter service cycle.

Fourth Generation · 2022–2026 · 3.0L V6 Turbo Diesel - 4WD (Platinum)

Diesel

Due by distance

  1. 40,000 km

    Evaluate the brake rotors and pads, given the vehicle's substantial mass.

  2. 80,000 km

    The period to consider a professional flush and service of the 10-speed automatic transmission fluid.

See all 5 issues for this oneDocumented for the exact year and engine you picked, including 3 rated critical.
Electrical1

01SYNC4 infotainment glitches and 12V battery drain (Next-Gen)

Sit in the car and work the screen hard — cameras, CarPlay/Android Auto, climate controls — for several minutes and watch for lag or reboots.2022 onwardElectrical
CommonElectrical $250–$1,200 to fix

Early Next-Gen Everests have a well-documented pattern of electrical gremlins: the large SYNC4 portrait screen freezing, rebooting or losing camera feeds, phantom warning messages, and flat 12V batteries caused by modules failing to sleep. Most issues are fixed under warranty with software updates and battery replacement, but they are annoying and a flat battery can leave you stranded. Check whether outstanding software updates have been applied.

Symptoms to notice

  • Touchscreen freezes, black screen or spontaneous reboots
  • Reversing camera feed missing or lagging
  • Flat 12V battery after the car sits a few days
  • Random warning chimes/messages that clear themselves

What to check

Sit in the car and work the screen hard — cameras, CarPlay/Android Auto, climate controls — for several minutes and watch for lag or reboots. Check the battery health (ask for it to be tested) and ask whether the car has ever failed to start.

Where to look: Dashboard touchscreen and 12V battery under the bonnet

Parts involved: 12V battery.

Ask the seller

  • “Have all outstanding SYNC/module software updates been done at a Ford dealer?”
  • “Has the 12V battery ever gone flat or been replaced?”
  • “Any history of screen or camera faults?”
Depends on the exact engine — 4 moreDocumented for a specific engine we could not confirm from what you picked. Check the engine code on the car.
Engine, transmission & cooling4

012.0 bi-turbo wet timing belt — oil-bathed belt degradation

The service book is the inspection here, and it is worth more than anything you can see.diesel2022–2025Engine
OccasionalEngine $2,500–$12,000 to fix

Can't confirm for this car

The 2.0 bi-turbo four-cylinder drives its camshafts with a belt that runs INSIDE the engine, bathed in oil — a wet belt. The design is meant to be quiet and long-lived, but the belt degrades as the oil ages and shed material can block the oil pickup, and this has been a known long-term weakness of the engine. Ford's own answer is telling: the 2026 Ranger and Everest drop the 2.0 bi-turbo entirely, leaving the 3.0 V6 and a revised single-turbo 2.0. For a buyer, that makes oil-change discipline the whole story on this engine — long or skipped intervals are what turn a wet belt from a non-issue into a destroyed engine, and the belt is not something you can look at without opening the engine.

Symptoms to notice

  • Rattle or whine from the engine, particularly on cold start
  • Low oil pressure warning
  • Engine warning light with camshaft/crankshaft correlation codes
  • Loss of power or a sudden stop with no restart, once it has failed

What to check

  1. The service book is the inspection here, and it is worth more than anything you can see.
  2. Look for oil changes at or inside Ford's interval with no gaps, done with the correct specification oil, and treat a car with missing years as a much bigger risk than the mileage suggests.
  3. Ask the owner what interval they use and whether the car has done mostly short trips or towing, both of which are hard on the oil.
  4. Pull the dipstick and look at the oil's condition — thick, black or gritty oil on this engine is a genuine warning rather than cosmetic.
  5. On a cold start, stand at the front and listen for a rattle or whine that is not there once warm.
  6. Ask whether the belt has ever been replaced and at what mileage.
  7. If a workshop inspection is possible: have the sump and oil pickup checked for belt debris, which is the earliest physical evidence there is.

Where to look: Inside the engine — timing belt running in oil behind the front cover, and the oil pickup in the sump

Parts involved: Timing belt, Turbocharger.

Ask the seller

  • “What oil-change interval has this engine had, and can I see every service record?”
  • “Has the timing belt ever been replaced?”
  • “Has the car done mostly towing or short trips?”

023.0 V6 diesel camshaft sprocket fracture — engine stall (recall)

Ford recalled 13,490 Ranger and Everest vehicles built 2022-2025 with the 3.0 V6 turbo-diesel because the left-hand camshaft sprocket can fracture.diesel2022–2025Engine
OccasionalEngine $0–$8,000 to fix

Can't confirm for this car

Ford recalled 13,490 Ranger and Everest vehicles built 2022-2025 with the 3.0 V6 turbo-diesel because the left-hand camshaft sprocket can fracture. When it does the engine stalls and the car loses drive with no warning, which is the reason it is a safety recall rather than a warranty item — losing power while towing or overtaking is the scenario Ford named. The fix is carried out free of charge at a Ford dealer, so the only question that matters to a buyer is whether it has been done. Do not assume it has: recall completion on used cars is patchy, and a private seller often does not know one exists.

Symptoms to notice

  • Engine stalling or cutting out while driving
  • Sudden loss of drive with no prior warning
  • Engine warning light with camshaft timing or correlation codes
  • Rattle or unusual noise from the front of the engine

What to check

Write down the VIN from the windscreen or the door jamb and check it against Ford's recall lookup — this is a free, five-minute check and it is the single most valuable thing you can do on this car. Ask the seller directly whether any recall work has been done and to show you the paperwork or dealer stamp. Look through the service book for a recall or field-service entry rather than just routine servicing. On the test drive, note whether the engine has ever cut out for them, and watch for any engine warning light. Because the remedy is free at a dealer, an outstanding recall is not a reason to reject the car — it is a reason to book it in before you drive it far. If a workshop inspection is possible: ask a Ford dealer to confirm the recall status against the VIN, which is definitive where a seller's memory is not.

Where to look: Front of the engine — left-hand camshaft sprocket behind the timing cover

Parts involved: Turbocharger.

Ask the seller

  • “Has the camshaft sprocket recall been carried out, and do you have the paperwork?”
  • “Has the engine ever stalled or cut out while driving?”
  • “Can I have the VIN to check the recall status?”

03Wet timing belt degradation (2.0 bi-turbo / single-turbo YN2S 'Panther')

diesel2018 onwardEngine
OccasionalEngine $2,500–$5,000 to fix

Can't confirm for this car

The 2.0-litre four-cylinder diesel fitted to UA II (2018-2022) and Next-Gen Everests runs its timing belt inside the engine, bathed in oil ('wet belt'). Oil contaminated by fuel from repeated DPF regeneration attacks the belt rubber; shed belt material can also block the oil pick-up. Ford's official replacement interval is 10 years/240,000 km, but documented failures well before that have led specialists to recommend replacement around 100,000-120,000 km. A snapped belt means valve-to-piston contact and effectively a new engine. Ford dropped the wet-belt bi-turbo from the Ranger/Everest line-up in 2025-26, which tells you what you need to know.

Symptoms to notice

  • Ticking or slapping noise from the front of the engine
  • Low oil pressure warning
  • Sludge or rubber debris in the oil filler/sump at service time
  • Most failures give little warning

What to check

Check the odometer against the service history — you want proof of short (10,000-12,500 km) oil change intervals with the correct low-ash oil, and on anything past 100,000 km ask whether the belt has been done. Lots of short urban trips (constant DPF regens) is the worst-case life for this belt. Budget for a preventative belt replacement if there is no evidence.

Where to look: Inside the engine at the front — belt runs in the oil, not visible without teardown

Parts involved: Timing belt, Turbocharger.

Ask the seller

  • “Has the wet timing belt (and oil pump belt) ever been replaced?”
  • “What oil spec was used and at what intervals?”
  • “Has the vehicle mostly done short urban trips or open-road running?”

042.0L EcoBlue DPF Clogging on Short Urban Trips

Check instrument cluster history for any stored DPF or emissions warnings.diesel2022 onwardEngineRead the full fault: symptoms, where to look, what to ask the seller
Other Ford Everest engines and years11 documented issues that do not apply to the one you picked.
Engine, transmission & cooling10

013.2L TDCi HPFP Metal Contamination of Fuel System

Request full fuel system service history and ask about any prior fuel starvation or hard-start events.diesel2015–2021Engine
OccasionalEngine $8,500–$24,000 to fix

Does not apply

The Bosch CP4.1 high-pressure fuel pump used in the 3.2L Duratorq TDCi can experience premature internal wear, generating metal swarf that circulates through the entire fuel system. This contaminates injectors, fuel rails, and fuel lines. Failure typically results in complete engine shutdown and requires replacement of nearly the entire fuel delivery system at catastrophic cost. The same failure mode is well documented across Ford Ranger PX models sharing this driveline and Bosch CP4.1 pump unit.

Symptoms to notice

  • Sudden loss of engine power or complete engine shutdown while driving
  • Hard starting or no-start condition
  • Rough running and misfires under load
  • Visible metallic debris or discolouration in fuel filter
  • Fuel injector rattle or audible knock from engine

What to check

  1. Request full fuel system service history and ask about any prior fuel starvation or hard-start events.
  2. Check for Ford dealer service records or TSB relating to HPFP on 3.2L TDCi.
  3. If a workshop inspection is possible: Scan for fuel pressure or injector fault codes via OBD.
  4. Remove and inspect the fuel filter for metallic particles or sludge.

Where to look: Bosch CP4.1 high-pressure fuel pump mounted on engine block, driven off camshaft; fuel rails and injectors downstream

Parts involved: High-pressure fuel pump.

Ask the seller

  • “Has the fuel filter ever been replaced and was any metal debris found?”
  • “Has the vehicle ever experienced hard starting or sudden loss of power?”
  • “Is there any record of fuel system warranty work or HPFP replacement?”
  • “Has the vehicle ever been run on poor-quality diesel or run very low on fuel?”

023.2 TDCi (P5AT) variable oil pump loss of prime or failure - oil starvation

Pull the dipstick and check the oil level and colour, and make sure there are no metallic flecks.diesel2015–2022Engine
OccasionalEngine $2,500–$16,000 to fix

Does not apply

The 3.2 five-cylinder uses a chain-driven, variable-displacement vane oil pump that is not self-priming. If the sump is left drained for more than about 10 minutes at a service, or the car sits unused for a long time, the pump can lose its prime and the engine runs with no oil pressure, which destroys bearings in seconds to minutes. Some pumps also wear out early, and many owners and 4x4 workshops retrofit a gear-type pump as insurance. A starved engine usually needs a rebuild or replacement engine.

Symptoms to notice

  • Oil pressure warning light after a service or long lay-up
  • Knocking or rattling that gets worse with revs
  • Tapping from the top end on start up that does not fade

What to check

  1. Pull the dipstick and check the oil level and colour, and make sure there are no metallic flecks.
  2. Start the engine from cold and watch the oil pressure warning light: it must go out within a second or two.
  3. Listen for any knocking or rattle that rises with revs.
  4. Ask who does the servicing and whether they know about the 3.2 oil pump priming issue, and whether the car has stood unused for months.
  5. Ask if a gear-type oil pump has been fitted and ask for the invoice.
  6. If a workshop inspection is possible: Have the workshop check actual oil pressure with a gauge and look for metal in the oil filter.

Where to look: Inside the sump at the bottom of the engine, chain driven from the crankshaft

Ask the seller

  • “Who services the car, and do they know about the 10-minute oil change rule on the 3.2?”
  • “Has the oil pump been replaced or upgraded to a gear pump?”
  • “Has the car ever shown the oil pressure light?”
  • “Has it sat unused for a long time?”

0310R80 10-speed auto fluid pump gear failure - loss of drive recall REC-003914 (2.0 bi-turbo)

diesel2018–2019Transmission
OccasionalTransmission $0–$9,500 to fix

Does not apply

Everest and Ranger 2.0 bi-turbo models with the 10R80 10-speed automatic built between 30 May 2018 and 16 October 2019 were recalled (Ford campaign 20S11, REC-003914) because the transmission fluid pump gears can fail while driving. When they do, the gearbox loses hydraulic pressure and the vehicle loses drive without warning, which Ford rated as a crash risk. The fix is a free dealer inspection and pump repair, and recall work never expires, but many of these Everests have changed hands several times and some never went back. A pump that has already failed usually means a gearbox rebuild or replacement if it is out of warranty.

Symptoms to notice

  • Sudden loss of drive while moving, engine still running
  • Transmission warning or wrench light on the dash
  • Whine from the gearbox that rises with engine speed
  • Gear engagement slow or missing after selecting Drive or Reverse

What to check

  1. Check the build date on the compliance plate in the driver door jamb: anything built 30 May 2018 to 16 October 2019 with the 2.0 bi-turbo is in the recall range.
  2. Ask for the service book or a dealer printout showing recall 20S11 was completed, and phone a Ford dealer with the VIN if there is no proof.
  3. On the test drive, select Drive and Reverse several times from a stop and make sure drive engages within about a second each time.
  4. Drive long enough for the gearbox to reach full temperature and listen for a whine that follows engine revs.
  5. If a workshop inspection is possible: Ask the dealer to confirm recall status against the VIN in the Ford system and to read transmission fault codes and line pressure data with a scan tool.

Where to look: Front of the 10R80 automatic gearbox, behind the engine under the centre of the car (pump is inside the bell housing)

Parts involved: Turbocharger.

Ask the seller

  • “Has recall 20S11 (transmission fluid pump) been done, and do you have the paperwork?”
  • “Has the car ever lost drive or gone into limp mode?”
  • “Has the gearbox been repaired or replaced?”

043.2 TDCi (P5AT) EGR cooler cracking - coolant into intake, hydrolock risk

With the engine cold, check the coolant expansion tank level and look for a tide mark above the current level that shows regular top ups.diesel2015–2022Cooling
OccasionalCooling $1,800–$4,000 to fix

Does not apply

The EGR cooler on the 3.2 five-cylinder can crack internally, letting coolant into the intake while the engine runs. Because the coolant level drops out of sight in the reservoir, many owners only find out when the engine overheats or hydrolocks, which can bend con rods and write off the engine. The cure is a new EGR cooler and hoses, and many 4x4 owners also fit a low coolant alarm. This is a separate part from the EGR valve that clogs with carbon.

Symptoms to notice

  • Coolant level dropping with no visible leak
  • White sweet-smelling exhaust smoke
  • Overheating, especially towing
  • Engine misfire or hard start after sitting

What to check

With the engine cold, check the coolant expansion tank level and look for a tide mark above the current level that shows regular top ups. Watch the exhaust on a cold start for white, sweet-smelling smoke. Use a phone torch to look around the EGR cooler hoses at the back of the engine for crusty pink or green coolant residue. Watch the temperature gauge on the test drive, especially up hills. Ask whether a coolant level alarm has been fitted or the EGR cooler replaced. If a workshop inspection is possible: Ask the workshop to pressure-test the cooling system and run a combustion gas test on the coolant to confirm an internal EGR cooler leak.

Where to look: EGR cooler at the rear of the engine near the firewall, between the exhaust manifold and the intake

Parts involved: EGR valve.

Ask the seller

  • “Has the EGR cooler been replaced?”
  • “Do you top up the coolant between services?”
  • “Has the engine ever overheated?”
  • “Is there a low coolant alarm fitted?”

0510R80 10-speed auto harsh, flaring or clunky shifts - valve body and adaptive calibration (2.0 bi-turbo)

Start from cold and select Reverse then Drive: engagement should be quick and without a bang.diesel2018–2022TransmissionRead the full fault: symptoms, where to look, what to ask the seller

06Injector seal (copper washer) failure — 'black death' carbon build-up (3.2 P5AT)

The 3.2-litre five-cylinder diesel shared with the Ranger can leak combustion gases past the injector sealing washers.diesel2015–2022EngineRead the full fault: symptoms, where to look, what to ask the seller

076R80 Torque Converter Clutch Shudder at Light Throttle

Test drive at steady light throttle between 60-80 km/h on a flat road.diesel2015–2021TransmissionRead the full fault: symptoms, where to look, what to ask the seller

082.0 bi-turbo (YN2S) EGR cooler internal leak - coolant loss and white smoke

diesel2018–2022Cooling
OccasionalCooling $1,500–$3,800 to fix

Does not apply

The EGR cooler on the 2.0 bi-turbo is a stainless heat exchanger that cools exhaust gas with engine coolant, and it can crack internally so coolant is drawn into the intake or exhaust. The first sign is usually a slowly dropping coolant level with no visible leak, then white sweet-smelling smoke, overheating and limp mode. Ignored, it can steam-clean or hydrolock a cylinder and damage the engine. The repair is a new EGR cooler, and it pays to check the head gasket at the same time if the engine has overheated.

Symptoms to notice

  • Coolant level keeps dropping with no drips under the car
  • White sweet-smelling smoke from the exhaust, worst on start up
  • Temperature gauge rising or overheating warning when towing
  • Rough running or limp mode

What to check

  1. Check the coolant expansion tank level with the engine cold: it should sit between the marks, and a tide mark well above the current level means it has been topped up.
  2. Look at the exhaust on a cold start for white, sweet-smelling smoke that does not clear once warm.
  3. Ask the seller how often they top up coolant.
  4. On the test drive, watch the temperature gauge on a long hill.
  5. If a workshop inspection is possible: Ask the workshop to do a cooling system pressure test, a combustion gas (block) test on the coolant, and an EGR cooler bypass test to confirm an internal leak.

Where to look: EGR cooler on the side of the engine next to the exhaust manifold, with two coolant hoses running into it

Parts involved: EGR valve, Turbocharger.

Ask the seller

  • “Do you have to top up the coolant between services?”
  • “Has the EGR cooler or head gasket been replaced?”
  • “Has the engine ever overheated?”

093.2L TDCi EGR Valve Carbon Fouling & Rough Idle

Cold-start the engine and observe idle quality and exhaust smoke after reaching operating temperature.diesel2015–2021EngineRead the full fault: symptoms, where to look, what to ask the seller

102.0 bi-turbo (YN2S) intercooler and boost hose failure - bang then limp mode

diesel2018–2022EngineRead the full fault: symptoms, where to look, what to ask the seller
Electrical1

01BorgWarner 4419 Transfer Case Shift Motor Sensor Failure

Test all four drive mode selections from a standstill and verify each mode engages and disengages correctly including 4L.2015–2021Electrical
OccasionalElectrical $850–$2,900 to fix

Does not apply

The BorgWarner 4419 transfer case in the UA Everest uses an electric shift motor with an internal position sensor to engage and disengage 4WD modes. The position sensor can fail or produce erratic readings, causing a 4WD fault warning on the instrument cluster, leaving the vehicle unable to change between 2H, 4H, and 4L, or intermittently dropping out of 4WD without warning. The fault requires replacement of the transfer case shift motor assembly. The electric motor and connector are also susceptible to water ingress on vehicles regularly used for river or creek crossings, accelerating sensor and motor failure.

Symptoms to notice

  • 4WD fault or 4x4 warning light illuminated on instrument cluster
  • Inability to change between 2H, 4H, and 4L drive modes
  • Vehicle stuck in 4WD high or unable to engage 4WD from 2H
  • Grinding or clicking from transfer case area when attempting mode change
  • 4WD mode indicator flashing or displaying incorrect selected mode

What to check

  1. Test all four drive mode selections from a standstill and verify each mode engages and disengages correctly including 4L.
  2. Inspect the transfer case shift motor connector for corrosion or water ingress, especially on vehicles with documented off-road or water crossing use.
  3. Check for any prior transfer case or 4WD warranty repair records.
  4. If a workshop inspection is possible: Check for any 4WD fault codes via OBD scanner.

Where to look: BorgWarner 4419 transfer case electric shift motor assembly, mounted on transfer case body at rear of transmission

Parts involved: Transfer case.

Ask the seller

  • “Has the 4WD system ever shown a fault warning light or refused to change modes?”
  • “Has the vehicle been used for water crossings and to what depth?”
  • “Has any 4WD system repair or transfer case work been performed?”
  • “Can you demonstrate all four drive modes selecting correctly including 4L engagement right now?”

Ford Everest faults in detail

Narrowed to the Ford Everest · 2023. Each of these has its own page: the symptoms, where to look, what to ask the seller and what the repair costs. Free, no account needed.

2.0L EcoBlue DPF Clogging on Short Urban TripsMajor · Engine

What these repairs cost on other cars

Some of the Ford Everest’s documented faults are repairs other models share. Each page lists the documented NZ cost for every model it affects.

Other Ford models

Ford Ranger45 documented faultsFord Focus37 documented faultsFord Falcon36 documented faultsFord Fiesta16 documented faultsFord Mondeo15 documented faultsFord XR813 documented faults

Ford Everest buyer questions

Is the Ford Everest reliable?

Like any used car, it depends on the specific example and its service history. Across the 16 documented faults for the Ford Everest, the recurring problem areas are engine, transmission, and cooling. A Ford Everest with a full service history and no signs of the issues listed on this page can be a sound buy but each one needs to be checked individually before you commit.

What are the most common problems with a used Ford Everest?

We've catalogued 16 known faults for the Ford Everest, covering engine, transmission, and cooling. All 16 are written out in full on this page, with the symptoms to notice, what to inspect, and typical repair costs for each. Free to read, no account needed.

How much do repairs cost on a Ford Everest?

Most single repairs on the Ford Everest fall between $650–$4,500 at NZ independent-workshop rates. Some of the 16 documented faults cost less and a few cost considerably more, and no one car needs them all. Knowing which ones to look for before you view is what lets you negotiate the price down or walk away.

Should I get a pre-purchase inspection on a Ford Everest?

Yes. A Ford Everest inspection focused on its known weak points is the single best way to avoid an expensive mistake. KickTyres gives you a guided, model-specific inspection plus a market valuation and negotiation figure for $24.90 far less than the cost of missing one of the faults on this page.