Skip to content
KickTyres
Nissan1995–2023 Critical issues documented

Nissan Pathfinder R52: common faults & what to check

The R52 is the Nissan Pathfinder built 2013–2022. It was sold here with the 2.5 hybrid and 3.5 V6 petrol. Of the 36 faults documented for the Pathfinder, 11 apply to this generation, each with its symptoms, what to inspect and a typical repair cost. Free, no account needed.

Check this exact Nissan Pathfinder

  • Odometer history
  • Money owing
  • Reported stolen
  • Ownership history
  • Official NZ vehicle register data
  • NZ owned and operated

Type the plate for the free basics. The full record is a paid check from $13.49, one car at a time, no subscription.

No NZ plate yet, or buying in Australia? Pick the generation and engine and start a free check below. New to KickTyres? How the check works →

36

Documented faults

Critical

Most serious

$700–$4,000

Typical repair

9

Systems covered

You're looking at the R52

2 engine variants are documented for this generation. Pick yours to narrow further, or keep reading for the generation as a whole.

Choose a different generation

Now narrow it to the engine

A 1.8 and a 2.4 of the same car do not fail the same way, so the faults below narrow to the engine as well as the year. Free, no account needed.

A 2014 Nissan Pathfinder is the R52 generation (2013 to 2022).

Start your free check on this Nissan Pathfinder

No plate needed. You get the risk score, the buyer's checklist and the guided inspection for the exact car you picked above — not the whole nameplate.

Nissan Pathfinder R52Engine not picked yet

Pick the engine above first: the Pathfinder came with 2, and without it the report has to show all of their faults. Pick the engine

Free. The paid plate check is separate, and stays optional.

Can't confirm for this car

Nissan Pathfinder · 2014

Narrowed to the year. No engine is recorded for this vehicle. Pick an engine to see which faults apply.

Tell us the engine, or check the engine code on the car, before relying on this.

  • No engine is recorded for this vehicle.

matched on year only

What to look out for

The checks worth doing on a Nissan Pathfinder before you hand over any money. Every documented fault is listed below, each with its own page.

  • Costly issue

    Also check at 9 and 3 o'clock for wheel bearing play to differentiate.

    See why

    Front Lower Control Arm Ball Joint Premature Wear

    The R52 Pathfinder front lower control arm uses a press-in ball joint that wears at an accelerated rate compared to expectations for a vehicle of this class. The lower ball joint is a load-bearing pivot and its wear allows the wheel to develop excessive play, causing imprecise steering, tyre edge wear, and eventually a dangerous loss of steering control. Worn ball joints typically clunk over bumps and cause a vague or wandering steering feel. In New Zealand and Australia, where gravel roads and potholes are common, wear rates are higher than in smoother urban environments. Many cases present at 80,000–130,000 km. The lower arm must typically be replaced as a complete assembly as the ball joint is not always separately serviceable to OE specification.

    What you would notice

    • Clunking or knocking from the front suspension over bumps or during parking manoeuvres
    • Vague or wandering steering feel
    • Uneven or feathered tyre wear on front tyres
    • Vehicle pulling to one side under braking
    • Vibration felt through the steering wheel at certain speeds

    Typically $700–$1,800 to put right.

  • Costly issue

    Turn the ignition on and listen for the ABS pump — a continuous whirr beyond about 10 seconds is the failure symptom Nissan describes.

    See why

    ABS actuator leak — fire risk recall (R52)

    R52 Pathfinders were captured in Nissan's large ABS actuator recall: the actuator pump can leak brake fluid onto an internal circuit board, which in the worst case can cause an electrical short and engine-bay fire. The recall advice was famously to park outside until fixed. The remedy (inspection and replacement of the actuator if leaking) is free at any Nissan dealer, but Japanese-import and privately imported cars may have slipped through the net, so completion must be verified rather than assumed.

    What you would notice

    • ABS warning light on the dash
    • ABS motor running longer than a few seconds after start-up
    • Brake fluid level dropping with no visible leak at the wheels

    Typically $0–$2,500 to put right.

See all 11 issues for this oneDocumented for the exact year and engine you picked, including 4 rated critical.
Body, brakes, suspension & interior2

01ABS actuator leak — fire risk recall (R52)

Turn the ignition on and listen for the ABS pump — a continuous whirr beyond about 10 seconds is the failure symptom Nissan describes.petrol2013–2021Brakes
OccasionalBrakes $0–$2,500 to fix

R52 Pathfinders were captured in Nissan's large ABS actuator recall: the actuator pump can leak brake fluid onto an internal circuit board, which in the worst case can cause an electrical short and engine-bay fire. The recall advice was famously to park outside until fixed. The remedy (inspection and replacement of the actuator if leaking) is free at any Nissan dealer, but Japanese-import and privately imported cars may have slipped through the net, so completion must be verified rather than assumed.

Symptoms to notice

  • ABS warning light on the dash
  • ABS motor running longer than a few seconds after start-up
  • Brake fluid level dropping with no visible leak at the wheels

What to check

  1. Turn the ignition on and listen for the ABS pump — a continuous whirr beyond about 10 seconds is the failure symptom Nissan describes.
  2. Check the brake fluid reservoir level.
  3. Most importantly, run the VIN through Nissan NZ/NZTA recall check to confirm the ABS recall has been completed, especially on a fresh import.

Where to look: ABS actuator unit in the engine bay, on the brake master cylinder side

Ask the seller

  • “Has the ABS actuator recall been completed on this VIN?”
  • “Does the ABS light ever come on?”

02Front Lower Control Arm Ball Joint Premature Wear

Also check at 9 and 3 o'clock for wheel bearing play to differentiate.petrol2013–2021Suspension
CommonSuspension $700–$1,800 to fix

The R52 Pathfinder front lower control arm uses a press-in ball joint that wears at an accelerated rate compared to expectations for a vehicle of this class. The lower ball joint is a load-bearing pivot and its wear allows the wheel to develop excessive play, causing imprecise steering, tyre edge wear, and eventually a dangerous loss of steering control. Worn ball joints typically clunk over bumps and cause a vague or wandering steering feel. In New Zealand and Australia, where gravel roads and potholes are common, wear rates are higher than in smoother urban environments. Many cases present at 80,000–130,000 km. The lower arm must typically be replaced as a complete assembly as the ball joint is not always separately serviceable to OE specification.

The front wheel of a car splayed outward with the lower control arm hanging down after a ball joint separation.Example of the part — not this vehicle

A separated lower ball joint: the control arm has dropped and the wheel has splayed out under the guard.

Elfix · CC0 · Wikimedia Commons

Symptoms to notice

  • Clunking or knocking from the front suspension over bumps or during parking manoeuvres
  • Vague or wandering steering feel
  • Uneven or feathered tyre wear on front tyres
  • Vehicle pulling to one side under braking
  • Vibration felt through the steering wheel at certain speeds

What to check

Also check at 9 and 3 o'clock for wheel bearing play to differentiate. Inspect the ball joint boot for cracking or grease leakage. Test drive on a rough surface and listen for clunks from the front. Check tyre wear pattern for evidence of alignment issues caused by worn joints. If a workshop inspection is possible: With the vehicle on a hoist or safely raised, grasp the front wheel at 12 and 6 o'clock positions and attempt to rock it — any visible movement at the lower ball joint indicates wear. A workshop pre-purchase inspection with a hoist is strongly recommended.

Where to look: Front suspension — lower control arm ball joint, both left and right sides

Parts involved: Ball joint.

Ask the seller

  • “Have the front lower control arm ball joints been inspected or replaced?”
  • “Has the vehicle had any front suspension work, alignment corrections, or clunking complaints?”
  • “Has the vehicle been driven regularly on unsealed roads or rough terrain?”
  • “Does the vehicle have a current WoF with no suspension advisory notes?”
Depends on the exact engine — 9 moreDocumented for a specific engine we could not confirm from what you picked. Check the engine code on the car.
Engine, transmission & cooling9

01VQ35DD 3.5 V6 Excessive Oil Consumption

Pull the dipstick and record level, then ask for the last service date and kilometre reading to calculate consumption rate.petrol2013–2021EngineRead the full fault: symptoms, where to look, what to ask the seller

02QR25DE 2.5 Timing Chain Tensioner Rattle and Stretch

petrol2013–2017Engine
OccasionalEngine $1,500–$3,500 to fix

Can't confirm for this car

The QR25DE 2.5-litre four-cylinder engine, used in lower-specification R52 Pathfinders in some markets, has a documented timing chain tensioner that loses hydraulic pressure on cold starts, allowing the chain to slap against the guide rail. Over time the chain stretches beyond the tensioner's compensation range, retarding cam timing and eventually risking chain jump or guide failure. The fault is accelerated by infrequent oil changes or use of low-viscosity oil outside the specification, as the tensioner relies entirely on oil pressure to maintain chain tension.

The front of a dual overhead camshaft engine with the timing cover removed, exposing the timing chain and sprockets.Example of the part — not this vehicle

The front of a twin-cam engine with the timing cover off — chain, sprockets and guides.

Logansenf · CC BY-SA 4.0 · Wikimedia Commons

Symptoms to notice

  • Rattling or clattering noise from the front of the engine on cold start, disappearing within seconds of oil pressure rise
  • Check engine light with cam timing fault codes P0011 or P0014
  • Rough idle or misfires on cold start that resolve as engine warms
  • Reduced power or fuel economy from retarded valve timing
  • Metal filings or fine debris visible in the oil on an oil drain inspection

What to check

  1. Cold-start the engine and listen immediately for a rattling or slapping sound from the front of the engine that clears within 5–10 seconds of oil pressure building — this is the tensioner signature.
  2. Scan for cam/crank correlation codes P0014, P0011, or P0341.
  3. Check service history for oil change intervals; QR25DE is sensitive to extended intervals.
  4. Inspect the timing cover area for oil seepage indicating chain guide dust from internal wear.

Where to look: Front of the engine block behind the timing cover; tensioner on the passenger side of the chain run

Parts involved: Timing chain.

Ask the seller

  • “Does the engine make a rattling noise for the first few seconds after a cold start?”
  • “Has the timing chain or tensioner ever been inspected or replaced?”
  • “Can you provide full service history showing oil change intervals?”

03Rear AWD Coupling Propshaft Seal Leak and Fluid Starvation

Check propshaft flanges at each end of the coupling for seepage.petrol2013–2021Transmission
OccasionalTransmission $400–$2,500 to fix

Can't confirm for this car

The R52 Pathfinder's rear AWD coupling (Borg Warner-supplied transfer unit) relies on a sealed fluid reservoir and multi-plate clutch pack to distribute torque to the rear axle. The input shaft seal and output flange seal are known to weep or fail, slowly draining coupling fluid onto the underside of the vehicle. Operating the coupling dry causes clutch pack overheating and scoring, resulting in permanent loss of rear drive engagement. The failure is insidious because the coupling has no fluid level check in the standard service schedule.

Symptoms to notice

  • Oil staining or seepage on the underside of the vehicle at the rear AWD coupling housing
  • AWD warning light appearing during sustained AWD use, particularly when the coupling is hot
  • Rear wheels not receiving drive in conditions where AWD should be active
  • Burning smell from underneath the vehicle during extended AWD operation
  • Fault codes related to rear torque delivery or AWD coupling temperature

What to check

Check propshaft flanges at each end of the coupling for seepage. On a safe surface with traction, confirm the rear wheels are receiving torque in AWD or 4WD Lock mode. If a workshop inspection is possible: Scan for AWD coupling temperature or torque delivery fault codes if a compatible scan tool is available. Raise the vehicle and inspect the rear AWD coupling (bolted between the propshaft and rear differential) for oil staining or fluid residue on the housing and surrounding underfloor.

Where to look: Rear AWD coupling unit mounted on the propshaft ahead of the rear differential, visible from underneath the rear of the vehicle

Parts involved: Clutch.

Ask the seller

  • “Has the underside of the vehicle ever been inspected for fluid leaks from the rear AWD coupling or propshaft?”
  • “Has the AWD system ever failed to engage or shown a warning light during wet or off-road use?”
  • “Has the rear coupling been serviced or had its seals replaced?”

04Transfer Case Control Motor (AWD Actuator) Failure

Scan for fault codes C1A12, C1A14, or C1152 (transfer case motor circuit/position).petrol2013–2021TransmissionRead the full fault: symptoms, where to look, what to ask the seller

05VQ35DD Intake Valve Carbon Fouling (Direct Injection)

Check for cold-start stumble, rough idle, or a lumpy idle that smooths out when fully warm.petrol2013–2021Engine
CommonEngine $600–$1,400 to fix

Can't confirm for this car

The VQ35DD uses direct injection, which bypasses the intake valves with fuel and therefore loses the detergent-cleaning effect that port injection provides. Crankcase oil vapour recirculated through the PCV system deposits carbon on the backs of the intake valves over 50,000–100,000 km. Heavy carbon build-up restricts airflow into each cylinder, causing rough idle, misfires, cold-start stumble, and progressive power loss. The only remedy is a chemical or walnut-shell media blast of the intake valves with the intake manifold removed.

Symptoms to notice

  • Rough or lumpy idle that is worse when cold and improves as the engine warms
  • Cold-start stumble or hesitation during the first minute of operation
  • Misfires on specific cylinders that persist despite new spark plugs (P0301–P0306)
  • Gradual reduction in fuel economy over high-kilometre ownership
  • Hesitation or flat spot under light throttle at cruise

What to check

Check for cold-start stumble, rough idle, or a lumpy idle that smooths out when fully warm. Review kilometre reading against service history; vehicles over 80,000 km with no walnut blast or intake service are likely affected. Misfires on specific cylinders that do not resolve with plug replacement indicate valve fouling on those cylinders. If a workshop inspection is possible: Inspect the intake manifold inlet ports with a borescope if available — heavy black carbon deposits on valve heads confirm the fault.

Where to look: Intake valves inside the cylinder head ports, accessed by removing the intake manifold; front bank (cylinders 1–3) and rear bank (cylinders 4–6)

Parts involved: Intake manifold, PCV / oil separator.

Ask the seller

  • “Has the intake manifold ever been removed for an intake valve cleaning or walnut shell blast?”
  • “Does the engine idle roughly or stumble when started cold?”
  • “Has the vehicle had any misfire codes or cylinder-specific faults?”

06Radiator Plastic End-Tank Crack Causing Coolant-CVT Fluid Cross-Contamination

Inspect the radiator lower end tanks for cracks, staining, or weeping at the crimp seams.petrol2013–2018CoolingRead the full fault: symptoms, where to look, what to ask the seller

07Xtronic CVT Belt/Pulley Shudder and Progressive Failure

With engine warm, apply light throttle from a standstill at 10–30 km/h and feel for a rhythmic vibration or judder through the driveline.petrol2013–2021TransmissionRead the full fault: symptoms, where to look, what to ask the seller

08CVT shudder, belt slip and premature failure (R52)

Test drive with multiple full-stop take-offs and a sustained hill or motorway on-ramp; any shudder, flare or lurch is disqualifying at asking price.petrol2013–2021TransmissionRead the full fault: symptoms, where to look, what to ask the seller

09Jatco JF016E CVT Overheating and Failure

Inspect CVT fluid via the check-plug on the transmission pan — fluid should be clear red with no burnt smell.petrol2012–2021TransmissionRead the full fault: symptoms, where to look, what to ask the seller
Other Nissan Pathfinder engines and years25 documented issues that do not apply to the one you picked.
Engine, transmission & cooling14

01YD25DDTi Rear Timing Chain Tensioner Catastrophic Failure

Check oil level and condition before driving.diesel2005–2013EngineRead the full fault: symptoms, where to look, what to ask the seller

02VG33E Timing Belt Failure on Interference Engine

Ask for documented timing belt replacement history with date and odometer.petrol1996–2004Engine
OccasionalEngine $600–$12,000 to fix

Does not apply

The VG33E 3.3-litre V6 in R50 Pathfinders uses a rubber timing belt driving an interference engine – if the belt fails, valves contact pistons immediately causing expensive internal damage. Belt replacement is required at 100,000 km or 5 years. Many NZ/AU R50 Pathfinders are now 20+ years old with no documented belt history, making this a priority check item on any purchase.

Symptoms to notice

  • Engine stops without warning at any speed (belt snap)
  • Squealing from front of engine before failure
  • Rough idle or difficult starting if belt has slipped a tooth
  • Timing-related misfires

What to check

Ask for documented timing belt replacement history with date and odometer. If unknown or undocumented, treat as overdue. Inspect for oil or coolant leaks from the timing cover area – contamination degrades belt life significantly. Budget for immediate belt, water pump, idler, and tensioner replacement as a purchase condition if history is absent.

Where to look: Front of the VG33E V6 – rubber timing belt connecting crankshaft to both camshafts

Parts involved: Timing belt.

Ask the seller

  • “When was the timing belt last replaced and at what odometer reading?”
  • “Was the water pump and tensioner replaced at the same service?”
  • “Are there any oil leaks visible near the timing cover?”

03Radiator Internal Partition Failure — ATF Contamination

With the engine cold, pull the ATF dipstick and inspect fluid closely for any milky, frothy, or brown-tinged appearance — healthy ATF is clear red.petrol2004–2013CoolingRead the full fault: symptoms, where to look, what to ask the seller

04VQ40DE Secondary Timing Chain Tensioner Failure

The VQ40DE 4.0-litre V6 uses a complex multi-stage timing chain system with secondary chain tensioners feeding the balance shaft and oil pump chains.petrol2005–2010EngineRead the full fault: symptoms, where to look, what to ask the seller

05YD25 2.5 diesel timing chain wear and failure — the notorious one (R51)

Cold-start the engine yourself and listen at the front of the engine for a rattle in the first seconds; also listen when fully hot at idle.diesel2005–2013EngineRead the full fault: symptoms, where to look, what to ask the seller

06Radiator transmission cooler failure — coolant/transmission 'milkshake' (SMOD)

With the engine cold, open the radiator cap and coolant bottle and look for any pink sludge or oily film — that is the fault in progress.2005–2013TransmissionRead the full fault: symptoms, where to look, what to ask the seller

07YD25DDTi Head Gasket Failure

Use a combustion gas (CO2) leak-detection fluid test on the coolant reservoir filler neck.diesel2005–2013EngineRead the full fault: symptoms, where to look, what to ask the seller

08VQ35DE oil consumption and loose power valve screws

Check the dipstick level and oil condition.petrol2001–2004Engine
OccasionalEngine $400–$6,000 to fix

Does not apply

The 3.5 V6 in late R50s has two documented weaknesses. First, the intake manifold power valve screws were fitted with insufficient threadlocker and can back out and drop into the engine, wrecking a cylinder. Second, high-mileage VQ35DEs burn oil because the oil control rings gum up and stick in the piston lands. The screw issue is cheap insurance to fix pre-emptively; heavy oil burning is only properly cured with a rebuild, so most owners just top up.

Symptoms to notice

  • Oil level dropping between services
  • Blue smoke on start-up or hard acceleration
  • Sudden severe misfire and metallic noise (screw ingestion)
  • Fouled spark plugs

What to check

  1. Check the dipstick level and oil condition.
  2. Watch the exhaust during a cold start and under hard acceleration for blue smoke.
  3. Ask if the power valve screws have been peened or loctited — enthusiast-owned cars often have this done and documented.
  4. A compression test before purchase is worthwhile on a high-km example.

Where to look: Engine internals; power valve screws live in the upper intake manifold plenum

Parts involved: Intake manifold.

Ask the seller

  • “How much oil does it use between changes?”
  • “Have the intake power valve screws ever been secured?”
  • “Has a compression test been done recently?”

09VQ40DE Primary Timing Chain Stretch

Cold-start the vehicle after an overnight soak and listen for chain rattle from the front of the engine for the first 10 seconds.petrol2004–2013Engine
OccasionalEngine $2,000–$4,500 to fix

Does not apply

The VQ40DE 4.0L V6 uses a primary timing chain driving the cam drive sprockets on both banks. Under sustained high-mileage operation, particularly with extended oil change intervals or use of incorrect-viscosity oil, the primary chain elongates beyond the tensioner's compensation range. Stretched chains cause camshaft timing to retard, reducing power and fuel economy and triggering variable cam timing fault codes. If the chain elongates sufficiently to jump a tooth on a cam sprocket, engine damage follows. The failure rate is substantially lower than the VQ35DE secondary tensioner issue but becomes a risk above 180,000 km on vehicles with incomplete service histories.

The front of a dual overhead camshaft engine with the timing cover removed, exposing the timing chain and sprockets.Example of the part — not this vehicle

The front of a twin-cam engine with the timing cover off — chain, sprockets and guides.

Logansenf · CC BY-SA 4.0 · Wikimedia Commons

Symptoms to notice

  • Cold-start timing chain rattle from the front of the engine
  • OBD codes P0011 or P0021 (camshaft position timing over-advanced)
  • Reduced power and increased fuel consumption at high mileage
  • Rough idle and hesitation under load

What to check

  1. Cold-start the vehicle after an overnight soak and listen for chain rattle from the front of the engine for the first 10 seconds.
  2. Scan for P0011 or P0021 variable valve timing codes.
  3. Inspect for any oil leaks from the front timing cover or valve cover gaskets, which often accompany high-mileage chain wear.
  4. Verify oil service records show correct grade (5W-30 fully synthetic) changed no longer than every 10,000 km.

Where to look: Front of engine, timing cover — primary chain between crankshaft and cam drive sprockets

Parts involved: Timing chain.

Ask the seller

  • “Has the timing chain or tensioner been inspected or replaced?”
  • “What oil grade and change interval has been maintained?”

10RE5R05A Automatic Transmission Torque Converter Shudder

The R51 Pathfinder with the 5-speed RE5R05A automatic transmission is susceptible to torque converter lock-up clutch shudder.2005–2013Transmission
CommonTransmission $1,800–$4,500 to fix

Does not apply

The R51 Pathfinder with the 5-speed RE5R05A automatic transmission is susceptible to torque converter lock-up clutch shudder. The lock-up clutch engages the torque converter at cruising speeds to eliminate slippage losses; when the friction material wears or the transmission fluid degrades, the clutch chatters as it tries to engage, producing a rhythmic shudder or vibration through the drivetrain. The sensation is most pronounced at light throttle between 60 and 110 km/h and is often misdiagnosed as a driveshaft or tyre issue. A fluid flush with Nissan-approved ATF (Matic-S or equivalent) sometimes temporarily resolves the symptom, but worn friction material requires torque converter replacement.

A cutaway automatic transmission torque converter showing the internal turbine and stator.Example of the part — not this vehicle

A torque converter, sectioned. The lock-up clutch inside is what shudders.

No machine-readable author provided. BerndB~commonswiki assumed (based on copyright claims). · CC BY-SA 3.0 · Wikimedia Commons

Symptoms to notice

  • Rhythmic shudder or vibration through the body and drivetrain at steady highway speeds (60-110 km/h) under light throttle, which disappears under hard acceleration or engine braking
  • Vibration resembling driving over a corrugated road surface that cannot be replicated at low speeds or when the torque converter is not in lock-up

What to check

  1. Test drive at a steady 70-110 km/h with light throttle pressure — a rhythmic vibration that disappears when you apply firm throttle or lift off entirely indicates torque converter shudder.
  2. Check the ATF condition on the dipstick: dark, burnt-smelling fluid that has not been changed at recommended intervals accelerates lock-up clutch wear.
  3. Ask for transmission service history.
  4. If a workshop inspection is possible: Connect a scan tool and monitor torque converter slip RPM at cruising speed; excessive slip during lock-up engagement confirms the fault.

Where to look: Torque converter housed inside the transmission bell housing, between the engine and the RE5R05A 5-speed automatic gearbox

Parts involved: Torque converter.

Ask the seller

  • “Has the automatic transmission fluid ever been changed, and what fluid type was used?”
  • “Does the car vibrate or shudder at highway speeds under light throttle?”
  • “Has any workshop diagnosed a torque converter or transmission issue?”

11VQ40 4.0 V6 upper timing chain tensioner wear (R51 petrol)

Cold-start the engine and listen at the front and both sides of the V6 for whining or buzzing — compare with a known-good car if you can.petrol2005–2013Engine
OccasionalEngine $2,000–$4,500 to fix

Does not apply

Petrol R51 Pathfinders with the VQ40DE 4.0 V6 suffer a known fault where the secondary (upper) timing chains cut through their plastic tensioner shoes, causing a whine or buzzing from the engine. Nissan revised the parts, but it can strike anywhere from 50,000 km to well past 160,000 km and regular servicing doesn't prevent it. Caught early it's a labour-heavy but survivable repair; ignored, chain failure wrecks the engine. Less catastrophic in practice than the diesel's chain problem, but the same rule applies: no rattles or whines allowed.

The front of a dual overhead camshaft engine with the timing cover removed, exposing the timing chain and sprockets.Example of the part — not this vehicle

The front of a twin-cam engine with the timing cover off — chain, sprockets and guides.

Logansenf · CC BY-SA 4.0 · Wikimedia Commons

Symptoms to notice

  • High-pitched whine or buzz from the engine that rises with revs
  • Rattle from the timing cover area
  • Noise most obvious between idle and 2,000 rpm from cold

What to check

  1. Cold-start the engine and listen at the front and both sides of the V6 for whining or buzzing — compare with a known-good car if you can.
  2. Rev gently to 2,000 rpm and listen for the noise following the revs.
  3. Ask for any invoices mentioning timing chain or tensioner work with the updated parts.

Where to look: Secondary timing chains at the front of each cylinder bank, behind the timing cover

Parts involved: Timing chain.

Ask the seller

  • “Has the engine ever whined or had timing chain tensioners replaced?”
  • “Were updated Nissan tensioner shoes fitted?”

12YD25DDTi Injector Body Cracking and Oil Dilution

Check the engine oil dipstick for a level noticeably above the full mark and smell the oil for a diesel or fuel odour.diesel2005–2010EngineRead the full fault: symptoms, where to look, what to ask the seller

13YD25DDTi EGR Cooler Cracking and Coolant Ingestion

Inspect the intake manifold and EGR pipe internals for coolant residue or white crystalline deposits.diesel2005–2013EngineRead the full fault: symptoms, where to look, what to ask the seller

14Nine-speed hesitation and low-speed shift harshness — mostly characteristic, not broken

2022 onwardTransmission
CommonTransmission $0–$700 to fix

Does not apply

The 2022 Pathfinder dropped the CVT that gave earlier ones such a poor name and fitted a ZF nine-speed conventional automatic instead — the same unit used by Honda, Acura and Jeep. It is the more durable choice, but it brought its own behaviour that owners frequently report as a fault: hesitation and lag pulling away from a stop, a jerk or lurch at low speed, and harsh or clunky downshifts. The reason is structural rather than a defect. To fit nine ratios into the space, ZF used dog clutches for fourth and seventh gears, and engaging a dog clutch means the transmission must match shaft speeds exactly before the teeth mesh, which needs a momentary cut in engine power — and that cut is what the driver feels as hesitation. Nissan has issued service bulletins refining the shift software, so a car on an old calibration behaves worse than one that has been updated. This matters to a buyer in the opposite direction to most faults: it is a reason not to walk away from a normal car, and a reason to ask about the software version rather than fear a gearbox rebuild.

Symptoms to notice

  • Delay before the car moves when you press the accelerator from a stop
  • Jerk or lurch at low speed, especially in stop-start traffic
  • Harsh or abrupt downshifts as you slow down
  • Clunk heard during gear changes
  • Behaviour improving noticeably after a dealer software update

What to check

  1. Drive it in traffic rather than on the open road, because that is where this shows and where you will find out whether the car is normal or genuinely faulty.
  2. Pull away from several standing starts with light throttle and note how long the pause is before the car moves — a short hesitation is characteristic of this gearbox and not a reason to walk away.
  3. What should worry you is different: slipping, where the engine revs climb without matching speed; a shift so harsh it rocks you in the seat; or the gearbox refusing to select a gear at all.
  4. Drive through a stretch of stop-start traffic and note whether the low-speed jerkiness is a mild shuffle or something violent.
  5. Accelerate firmly through the gears once and confirm each change happens cleanly.
  6. Watch for any warning light throughout.
  7. Ask the seller whether the transmission software has been updated at a Nissan dealer and whether there is an invoice — a car on the latest calibration behaves noticeably better, and a car that has never been back is worth a dealer visit.
  8. If a workshop inspection is possible: ask for the transmission control module software version and any stored faults to be confirmed.

Where to look: Gearbox — nine-speed automatic, dog clutches on fourth and seventh gears

Parts involved: Clutch.

Ask the seller

  • “Has the transmission software ever been updated at a Nissan dealer?”
  • “Does it ever slip, flare or refuse to select a gear, as opposed to just hesitating?”
  • “Has a transmission warning light ever appeared?”
Electrical3

01Forward emergency braking false activation (R52)

Check the dash for FEB warning lights and scroll the trip computer menus for stored system messages.petrol2015–2021Electrical
OccasionalElectrical $300–$2,500 to fix

Does not apply

R52 Pathfinders with forward emergency braking (standard on most 2015-on ST-L/Ti grades) have a documented pattern of the system falsely detecting obstacles — railway crossings, bridges and parked cars — and applying the brakes with nothing ahead. It generated a US class action and NHTSA complaints, and Nissan issued software reprogramming through dealers. On used examples the radar can also fail or fall out of alignment after bumper repairs, disabling the system.

Symptoms to notice

  • Car braking hard with nothing in front
  • FEB/forward collision warning light on
  • 'Front radar unavailable' message
  • System warnings at railway crossings or metal bridges

What to check

  1. Check the dash for FEB warning lights and scroll the trip computer menus for stored system messages.
  2. Ask whether the FEB software update has been done at a dealer.
  3. Look for evidence of front-end repairs — a resprayed or replaced bumper can block or misalign the radar behind the badge.

Where to look: Radar unit behind the front grille badge; camera at the top of the windscreen

Ask the seller

  • “Has the forward emergency braking ever activated by itself?”
  • “Has the FEB software update or radar alignment been done?”

02Infotainment freezes and driver-assist electronics glitches (R53)

petrol2022 onwardElectrical
OccasionalElectrical $200–$2,500 to fix

Does not apply

Early R53 Pathfinders have a pattern of electronic niggles rather than mechanical faults: the touchscreen freezing or rebooting, wireless Apple CarPlay/Android Auto dropping out, the 360-degree camera going black, and occasional spurious driver-assist warnings. Nissan addresses most of it with software updates at the dealer, but some owners have needed display units or cameras replaced under warranty. Annoying rather than dangerous, but out of warranty a replacement screen assembly is genuinely expensive, so verify everything works before purchase.

Symptoms to notice

  • Touchscreen freezing or rebooting mid-drive
  • Wireless CarPlay/Android Auto disconnecting
  • Black or glitching reversing/360 camera view
  • Random driver-assist warning chimes

What to check

Spend ten minutes working the whole infotainment system: pair your own phone wirelessly, use the reversing and 360 cameras several times, and cycle through every menu. Ask whether infotainment software updates have been performed at a dealer and confirm the remaining warranty, since electronics claims are common on these.

Where to look: Centre touchscreen and instrument cluster; cameras in the grille, mirrors and tailgate

Ask the seller

  • “Have there been any infotainment or camera problems, and were they fixed under warranty?”
  • “Is the software up to date per the Nissan dealer?”

03Air Conditioning Compressor Clutch Failure

Turn on the AC and observe the front of the compressor — the inner clutch disc should engage and spin with the compressor shaft when AC is active.2005–2013Electrical
CommonElectrical $450–$1,600 to fix

Does not apply

The R51 Pathfinder's air conditioning compressor uses an electromagnetic clutch to engage and disengage the compressor from the engine-driven belt pulley. The clutch consists of an electromagnetic coil, a pulley bearing, and a friction disc. Over time the coil winding can develop open-circuit failures, the air gap between the friction disc and pulley face widens beyond specification as the friction material wears, or the pulley bearing seizes. Any of these failures results in the compressor not engaging when the AC is selected. Seized pulley bearings carry an additional risk of belt failure if the bearing locks and the belt is forced to slip or snap on a stationary pulley.

Symptoms to notice

  • Air conditioning system blows ambient air only — no cooling — with the AC compressor pulley spinning freely but the clutch disc not engaging
  • Intermittent AC operation that becomes progressively less reliable, sometimes accompanied by a clicking sound as the clutch attempts to engage without successfully holding

What to check

  1. Turn on the AC and observe the front of the compressor — the inner clutch disc should engage and spin with the compressor shaft when AC is active; if only the outer pulley spins freely and the disc does not engage, the clutch has failed.
  2. Listen for a clicking engagement sound followed by compressor operation.
  3. Check for a burnt or acrid smell from the clutch area.
  4. Check the compressor clutch relay and fuse before condemning the clutch itself.
  5. If a workshop inspection is possible: Measure the air gap between the friction disc and pulley with feeler gauges — the specification is typically 0.3-0.6 mm; excessive gap prevents engagement even with a functional coil.

Where to look: AC compressor mounted on the front-lower driver's side of the engine, driven by the serpentine accessory belt; clutch assembly at the front face of the compressor

Parts involved: Clutch.

Ask the seller

  • “Is the air conditioning currently working — does it produce cold air?”
  • “Has the AC compressor or clutch ever been replaced or repaired?”
  • “Has the AC ever stopped working and been recharged or repaired since new?”
Body, brakes, suspension & interior7

01Structural rust: chassis rails, floor pans, strut towers (R50)

Get underneath with a torch: probe the chassis rails, floor pans and rear crossmember with your thumb — sound metal doesn't flex or flake.2000–2004Body & RustRead the full fault: symptoms, where to look, what to ask the seller

02Driver's powered seat frame weld recall — seat can detach from its bracket

Run the VIN past a Nissan dealer to confirm this recall has been done — free, quick and conclusive.2023Interior
RareInterior $0–$1,800 to fix

Does not apply

The 2023 Pathfinder was recalled because the driver's powered seat may not be fully secured to the seat frame: the frame welds can detach from the rear inboard seat bracket. A driver's seat that is not properly anchored is a serious matter in a crash, and it can also let the seat move unexpectedly in normal driving. This was the single NHTSA recall on the 2023 model year, so unlike the 2022 car there is one specific thing to ask about. The dealer repair is free, and the check costs nothing.

Symptoms to notice

  • Driver's seat rocking or shifting when it should be solid
  • Creak, click or knock from under the driver's seat over bumps
  • Seat feeling loose on one side, usually the inboard rear corner
  • Seat moving slightly under hard braking or acceleration

What to check

Run the VIN past a Nissan dealer to confirm this recall has been done — free, quick and conclusive. Then check it from the driver's seat, which is easy on this one. Sit down normally, take hold of the seat and try to rock it forwards, backwards and side to side; a properly secured seat feels solid in every direction. Pay particular attention to the inboard rear corner, nearest the centre console, since that is the bracket named in the recall. Run the seat through its full powered travel and its height and tilt adjustment, listening for any click or knock and feeling for any part of the range where it feels less secure. On the drive, brake firmly once from a moderate speed in a safe place and note whether you feel the seat shift under you, and listen for creaking from beneath over rough surfaces. Ask the seller for the recall paperwork. If a workshop inspection is possible: ask for the driver's seat mounting and frame welds to be checked directly.

Where to look: Driver's seat — seat frame welds at the rear inboard seat bracket

Ask the seller

  • “Has the driver's seat recall been completed, and is there a dealer invoice?”
  • “Does the driver's seat creak, click or move at all?”
  • “Has the seat ever been removed or repaired?”

03Secondary hood latch bracket weld recall — bonnet can fly open

Check the VIN with a Nissan dealer first — the 2022 Pathfinder carries several separate campaigns and a single free check covers all of them at once.2022Body & Rust
OccasionalBody & Rust $0–$1,200 to fix

Does not apply

Nissan recalled 2022 Pathfinders because insufficient welds may allow the secondary hood latch retainer bracket to detach from the front bumper assembly. The secondary latch is the backup that stops the bonnet flying up if the primary catch is left unlatched or lets go, so with the bracket detached that safety net is gone and a bonnet that comes open at speed blocks the windscreen completely. The 2022 Pathfinder was recalled five times by NHTSA in total, which is a lot for one model year and a good reason to run a full VIN check rather than asking about this one alone. The repair is free at a dealer.

Symptoms to notice

  • Bonnet feeling loose or lifting slightly at speed
  • Bonnet not sitting flush with the wings or catching unevenly
  • Secondary catch not engaging when the bonnet is released
  • Rattle from the front of the bonnet over bumps

What to check

Check the VIN with a Nissan dealer first — the 2022 Pathfinder carries several separate campaigns and a single free check covers all of them at once. Then test the bonnet by hand, which takes a minute. Pull the bonnet release inside the car and go to the front: the bonnet should rise a little and stop, held by the secondary catch, so that you have to reach in and release it deliberately. If the bonnet simply lifts free with no second stage, stop and ask why. Close it from a normal height and confirm it catches first time and sits flush and even with both wings, with matching gaps down each side. Push down firmly on the front edge of the closed bonnet and check there is no movement or rattle. Look at the front of the bumper where the latch mechanism mounts for anything obviously loose, bent or previously repaired. On the drive, note any flutter or movement from the bonnet at open-road speed. If a workshop inspection is possible: ask for the bonnet latch mounting to be checked directly.

Where to look: Front of the vehicle — secondary hood latch retainer bracket on the front bumper assembly

Ask the seller

  • “Have all outstanding Nissan recalls been completed, and is there a dealer invoice?”
  • “Does the bonnet always catch on the safety catch when released?”
  • “Has the front of the car ever had panel or bumper repair?”

04Chassis Rail and Floor Pan Structural Rust

Use a torch to inspect chassis rails from front to rear.petrol1995–2004Body & RustRead the full fault: symptoms, where to look, what to ask the seller

05Rear trailing arm bushings worn — the R50 'death wobble'

Test drive at open-road speed over a patchy stretch of seal and feel for the rear moving around.2000–2004SuspensionRead the full fault: symptoms, where to look, what to ask the seller

06Front Lower Ball Joint Wear and Play

Lift each front wheel and check for vertical and lateral play in the lower ball joint.petrol1995–2004Suspension
CommonSuspension $500–$1,100 to fix

Does not apply

R50 Pathfinders develop front lower ball joint wear at moderate mileage. Worn joints cause handling vagueness, uneven tyre wear, and WOF failure. Severely worn joints can separate suddenly, causing loss of vehicle control. OEM joints have no grease nipples and are often neglected; aftermarket replacements with greaseable nipples are the preferred fix and last longer.

The front wheel of a car splayed outward with the lower control arm hanging down after a ball joint separation.Example of the part — not this vehicle

A separated lower ball joint: the control arm has dropped and the wheel has splayed out under the guard.

Elfix · CC0 · Wikimedia Commons

Symptoms to notice

  • Clunking from front suspension over bumps or during steering input
  • Vague or wandering steering feel
  • Uneven front tyre wear
  • WOF failure for front suspension play
  • Vehicle pulling to one side

What to check

  1. Lift each front wheel and check for vertical and lateral play in the lower ball joint.
  2. A rocking test with hands at 12 and 6 o'clock on the tyre reveals ball joint play.
  3. Inspect control arm bushings simultaneously as they often wear in parallel.

Where to look: Front suspension – lower ball joint connecting the lower control arm to the steering knuckle on each side

Parts involved: Ball joint.

Ask the seller

  • “Have the front ball joints been replaced and at what mileage?”
  • “Has the vehicle passed a recent WOF with no suspension advisories?”
  • “Has any steering or front suspension work been done?”

07Front Lower Control Arm Ball Joint Wear

Any detectable vertical play indicates lower ball joint wear.2005–2013Suspension
CommonSuspension $400–$1,000 to fix

Does not apply

The front lower control arm ball joints on the R51 Pathfinder are subject to accelerated wear due to the vehicle's kerb weight and the load placed on the suspension during off-road use, towing, and New Zealand's unsealed road conditions. The ball joint consists of a hardened steel ball stud moving within a polymer or sintered metal socket; as the socket wears, radial and axial play develops. Worn ball joints degrade steering accuracy, produce audible suspension noise, and in an advanced state present a safety-critical failure risk — a completely failed ball joint allows the wheel to collapse outward, resulting in loss of vehicle control.

The front wheel of a car splayed outward with the lower control arm hanging down after a ball joint separation.Example of the part — not this vehicle

A separated lower ball joint: the control arm has dropped and the wheel has splayed out under the guard.

Elfix · CC0 · Wikimedia Commons

Symptoms to notice

  • Clunking or knocking from one or both front corners of the vehicle when traversing bumps, speed humps, or rough roads
  • Vague or wandering steering feel, with the vehicle pulling or drifting during braking
  • Uneven front tyre wear, particularly accelerated wear on inner or outer tread edges

What to check

Any detectable vertical play indicates lower ball joint wear. Also grasp at 9 and 3 o'clock to check upper ball joint and wheel bearing. Visually inspect the ball joint dust boot for cracks, splits, or grease extrusion — torn boots cause rapid joint degradation from dirt ingress. Test drive on a rough surface and listen for clunking from the front suspension over bumps. If a workshop inspection is possible: Lift the front of the vehicle and grasp each front tyre at the 6 and 12 o'clock positions, then rock the wheel.

Where to look: Front lower control arm (both driver and passenger sides), ball joint located at the outboard end of the arm where it connects to the front wheel hub/steering knuckle

Parts involved: Ball joint.

Ask the seller

  • “Have the front lower ball joints been replaced? If so, when and by which workshop?”
  • “Has the car been used off-road or for towing regularly?”
  • “Has a workshop ever flagged suspension or ball joint wear on a WOF inspection?”
Fluid leaks1

01Rear Differential Pinion Seal Failure

The rear differential pinion seal on the R51 Pathfinder is a rubber lip seal that retains gear oil around the input flange of the rear differential.2005–2013Fluid Leaks
OccasionalFluid Leaks $280–$650 to fix

Does not apply

The rear differential pinion seal on the R51 Pathfinder is a rubber lip seal that retains gear oil around the input flange of the rear differential. Age, heat cycling, and high mileage cause the seal lip to harden and shrink, allowing gear oil to seep or stream past the flange. The R51's rear differential is vulnerable to accelerated seal wear after any water crossing where the hot differential cools rapidly on submersion, drawing water past a weakened seal. If the gear oil level drops sufficiently, differential pinion and crown wheel bearings run dry, resulting in whining, overheating, and potentially catastrophic differential failure.

Symptoms to notice

  • Visible gear oil leak — fresh oily residue or drips from the front face of the rear differential housing around the propshaft input flange
  • Whining or howling noise from the rear of the vehicle that varies with road speed, indicating low differential oil level due to seal leakage

What to check

  1. Inspect the front face of the rear differential housing where the propshaft connects — look for fresh gear oil staining, drips, or a wet oily residue around the input flange and seal area.
  2. Check the differential drain/fill plug area for oil level (should be at the fill hole with the vehicle level).
  3. A whining or humming noise from the rear that increases with vehicle speed can indicate a differential running low on oil due to seal leakage.
  4. Inspect the underside of the vehicle for a gear oil trail running rearward from the front of the differential.

Where to look: Rear differential housing, at the front face where the tailshaft/propshaft input flange connects to the pinion shaft

Parts involved: Differential.

Ask the seller

  • “Has the rear differential pinion seal ever been replaced?”
  • “Has the vehicle been driven through water crossings or flood conditions?”
  • “When was the rear differential oil last changed, and was the level checked at that time?”

Nissan Pathfinder faults in detail

Narrowed to the Nissan Pathfinder · 2014. Each of these has its own page: the symptoms, where to look, what to ask the seller and what the repair costs. Free, no account needed.

CVT shudder, belt slip and premature failure (R52)Critical · TransmissionJatco JF016E CVT Overheating and FailureCritical · TransmissionRadiator Plastic End-Tank Crack Causing Coolant-CVT Fluid Cross-ContaminationCritical · CoolingTransfer Case Control Motor (AWD Actuator) FailureMajor · TransmissionVQ35DD 3.5 V6 Excessive Oil ConsumptionMajor · EngineXtronic CVT Belt/Pulley Shudder and Progressive FailureCritical · Transmission

What these repairs cost on other cars

Some of the Nissan Pathfinder’s documented faults are repairs other models share. Each page lists the documented NZ cost for every model it affects.

Other Nissan models

Nissan Patrol48 documented faultsNissan Navara45 documented faultsNissan X-Trail45 documented faultsNissan Note31 documented faultsNissan Qashqai28 documented faultsNissan Serena27 documented faults

Nissan Pathfinder buyer questions

Is the Nissan Pathfinder reliable?

Like any used car, it depends on the specific example and its service history. Across the 36 documented faults for the Nissan Pathfinder, the recurring problem areas are cooling, engine, and transmission. A Nissan Pathfinder with a full service history and no signs of the issues listed on this page can be a sound buy but each one needs to be checked individually before you commit.

What are the most common problems with a used Nissan Pathfinder?

We've catalogued 36 known faults for the Nissan Pathfinder, covering cooling, engine, and transmission. All 36 are written out in full on this page, with the symptoms to notice, what to inspect, and typical repair costs for each. Free to read, no account needed.

How much do repairs cost on a Nissan Pathfinder?

Most single repairs on the Nissan Pathfinder fall between $700–$4,000 at NZ independent-workshop rates. Some of the 36 documented faults cost less and a few cost considerably more, and no one car needs them all. Knowing which ones to look for before you view is what lets you negotiate the price down or walk away.

Should I get a pre-purchase inspection on a Nissan Pathfinder?

Yes. A Nissan Pathfinder inspection focused on its known weak points is the single best way to avoid an expensive mistake. KickTyres gives you a guided, model-specific inspection plus a market valuation and negotiation figure for $24.90 far less than the cost of missing one of the faults on this page.