Renault1998–2019 Critical issues documented

Renault Lutecia IV: common faults & what to check

The IV is the Renault Lutecia built 2013–2019. Of the 11 faults documented for the Lutecia, 7 apply to this generation, each with its symptoms, what to inspect and a typical repair cost. Free, no account needed.

Check this exact Renault Lutecia

Odometer history
Money owing
Reported stolen
Ownership history

Official NZ vehicle register data
NZ owned and operated

Type the plate for the free basics. The full record is a paid check from $13.49, one car at a time, no subscription.

No NZ plate yet, or buying in Australia? Pick the generation and engine and start a free check below. New to KickTyres? How the check works →

Documented faults

Critical

Most serious

$600–$2,800

Typical repair

Systems covered

You're looking at the IV

Everything below is narrowed to this variant. Pick a different one to change it.

2013–2019IV Selected2013–2019IVEngine not documented for this generationEngine not documentedDocumented issues7 knownSee faults & what to checkPhoto: M 93 via Wikimedia Commons, CC BY-SA 3.0 de.

Choose a different generation

Now narrow it to the engine

A 1.8 and a 2.4 of the same car do not fail the same way, so the faults below narrow to the engine as well as the year. Free, no account needed.

A 2014 Renault Lutecia is the IV generation (2013 to 2019).

Start your free check on this Renault Lutecia

No plate needed. You get the risk score, the buyer's checklist and the guided inspection for the exact car you picked above — not the whole nameplate.

Renault Lutecia IV

Can't confirm for this car

Renault Lutecia · 2014

Narrowed to the year. No engine is recorded for this vehicle. Pick an engine to see which faults apply.

Tell us the engine, or check the engine code on the car, before relying on this.

No engine is recorded for this vehicle.

matched on year only

What to look out for

The checks worth doing on a Renault Lutecia before you hand over any money. Every documented fault is listed below, each with its own page.

Costly issue
Inspect the passenger footwell for moisture evidence.
See why
UCH/BCM Body Control Module Failure
The Renault UCH (Unite Centrale Habitacle) body control module manages the immobilizer, central locking, power windows, lighting, dashboard functions, and wipers. Failure is triggered by voltage spikes during jump-starting, water ingress into the module housing, or age-related capacitor degradation. Symptoms span multiple unrelated systems simultaneously. Replacement requires specialist programming and pairing to the vehicle's immobilizer system — an off-the-shelf swap does not work.
What you would notice
- No-start condition with all dashboard warning lights on simultaneously
- Central locking and windows failing at the same time
- Multiple unrelated fault codes across different systems
- Intermittent complete electrical shutdown
Typically $300–$1,300 to put right.
Costly issue
After a short test drive, carefully feel each front wheel near the centre — a seized caliper will make that wheel noticeably hotter than the other.
See why
Front Brake Caliper Sticking and Seizure
Front brake calipers on Clio IV are known to seize or stick due to corrosion of the caliper slider pins and piston seal deterioration. A stuck caliper causes the brake pad to drag against the disc, causing rapid and uneven pad and disc wear, excessive brake heat, pulling under braking, and risk of brake fade. Calipers are exposed to road salt and water on NZ roads and seize faster than expected on cars with infrequent brake servicing. Replacement is typically required rather than rebuild once seizure is established.
What you would notice
- Car pulling to one side under braking
- Brake disc or wheel hot after normal driving
- Grinding or rubbing noise from front brakes
- Uneven pad wear between left and right
- Burnt brake smell from one front wheel
Typically $280–$700 to put right.

See all 7 issues for this oneDocumented for the exact year and engine you picked, including 2 rated critical.

Electrical1

01UCH/BCM Body Control Module Failure

Inspect the passenger footwell for moisture evidence.2005–2019Electrical$300–$1,300

CommonElectrical $300–$1,300 to fix

The Renault UCH (Unite Centrale Habitacle) body control module manages the immobilizer, central locking, power windows, lighting, dashboard functions, and wipers. Failure is triggered by voltage spikes during jump-starting, water ingress into the module housing, or age-related capacitor degradation. Symptoms span multiple unrelated systems simultaneously. Replacement requires specialist programming and pairing to the vehicle's immobilizer system — an off-the-shelf swap does not work.

Symptoms to notice

No-start condition with all dashboard warning lights on simultaneously
Central locking and windows failing at the same time
Multiple unrelated fault codes across different systems
Intermittent complete electrical shutdown

What to check

Inspect the passenger footwell for moisture evidence.
Test all windows, locking, and the immobilizer by starting the car normally.
If a workshop inspection is possible: Perform a full multi-system diagnostic scan and check whether fault codes span unrelated modules (ABS, airbag, instrument cluster, UCH) simultaneously — this pattern indicates BCM failure rather than individual component faults.

Where to look: Under dashboard, typically in passenger footwell area

Ask the seller

“Has the car ever had unexplained electrical faults or refused to start?”
“Has the BCM or UCH module been replaced or reprogrammed?”

Body, brakes, suspension & interior1

02Front Brake Caliper Sticking and Seizure

After a short test drive, carefully feel each front wheel near the centre — a seized caliper will make that wheel noticeably hotter than the other.2012–2019Brakes$280–$700

CommonBrakes $280–$700 to fix

Front brake calipers on Clio IV are known to seize or stick due to corrosion of the caliper slider pins and piston seal deterioration. A stuck caliper causes the brake pad to drag against the disc, causing rapid and uneven pad and disc wear, excessive brake heat, pulling under braking, and risk of brake fade. Calipers are exposed to road salt and water on NZ roads and seize faster than expected on cars with infrequent brake servicing. Replacement is typically required rather than rebuild once seizure is established.

Symptoms to notice

Car pulling to one side under braking
Brake disc or wheel hot after normal driving
Grinding or rubbing noise from front brakes
Uneven pad wear between left and right
Burnt brake smell from one front wheel

What to check

After a short test drive, carefully feel each front wheel near the centre — a seized caliper will make that wheel noticeably hotter than the other.
Check pad thickness and look for uneven wear between left and right.
Push brake caliper slider pins to check free movement.

Where to look: Front brake calipers, both sides

Parts involved: Brake disc and pads.

Ask the seller

“Have the front brake calipers or slider pins been serviced or replaced?”
“Does the car pull to one side when braking?”
“When were the front brake pads and discs last replaced?”

Depends on the exact engine — 5 moreDocumented for a specific engine we could not confirm from what you picked. Check the engine code on the car.

Engine, transmission & cooling5

011.2 TCe Timing Chain Stretch and Tensioner Failure

Start cold and listen for chain rattle from the cam cover area in the first 30 seconds.petrol2012–2019EngineCan't confirm for this car$2,800–$6,500

CommonEngine $2,800–$6,500 to fix

Can't confirm for this car

The 1.2 TCe H5F engine used in Clio III phase 2 and Clio IV is documented for premature timing chain stretch caused by a weak plastic tensioner. The chain can jump teeth or snap without warning, causing valve-to-piston contact and catastrophic engine damage. Failure rate accelerates with extended oil change intervals. Documented across multiple owner forums, independent workshop TSBs, and Renault technical notes.

Symptoms to notice

Metallic rattling from front of engine on cold start that fades when warm
Check engine light with camshaft or crankshaft position sensor codes
Engine cuts out suddenly or fails to start
Rough idle or misfires after startup

What to check

Start cold and listen for chain rattle from the cam cover area in the first 30 seconds.
Check service history for oil change frequency — chain wear accelerates beyond 10,000 km intervals.
Request compression test if any rattle is present.

Where to look: Front of engine beneath timing chain cover

Parts involved: Timing chain.

Ask the seller

“Has the timing chain and tensioner ever been inspected or replaced?”
“What oil change interval has been used — every 10,000 km or more frequently?”
“Has the car ever rattled on cold start?”

02D4F 1.2 16v Cam Belt Overdue Replacement Risk

Request written evidence of timing belt replacement date and mileage.petrol1998–2016EngineCan't confirm for this car$380–$5,500

OccasionalEngine $380–$5,500 to fix

Can't confirm for this car

The D4F 1.2 16v petrol engine uses a rubber timing belt that requires replacement every five years or 80,000 km regardless of apparent condition. This is an interference-type engine: a snapped or jumped belt causes immediate piston-to-valve contact, resulting in bent valves and, in most cases, an engine that cannot be economically repaired. Many pre-owned examples in NZ and AU arrive without documented belt history, significantly elevating failure risk.

Symptoms to notice

Engine stops suddenly without warning or misfires
Rattling from front of engine on start-up
Loss of compression on any cylinder
Starter motor cranks but engine does not fire after belt snap

What to check

Request written evidence of timing belt replacement date and mileage.
Verify water pump and tensioner were replaced concurrently with the belt, as water pump failure can drag the belt off.
If a workshop inspection is possible: Remove the upper plastic timing cover and inspect belt condition — look for cracking, glazing, fraying on edges, or contamination by oil or coolant.

Where to look: Front of engine behind plastic cover, driver's side

Parts involved: Timing belt.

Ask the seller

“When was the cam belt last replaced and by whom?”
“Was the water pump and tensioner replaced at the same service?”

03K9K 1.5 dCi Common Rail Injector Failure

Cold-start and warm the engine fully, then listen for metallic tapping at idle.diesel2005–2019EngineCan't confirm for this car$800–$2,800

CommonEngine $800–$2,800 to fix

Can't confirm for this car

The Bosch/Delphi common rail injectors on the K9K 1.5 dCi engine are a documented weak point across the platform. High-pressure fuel contamination, copper seat erosion, and injector tip wear cause irregular fuel delivery, fuel return leaks, and hard restarting when hot. Multiple injectors often fail in sequence rather than individually, and the failure mode is recognised widely by Renault specialists and parts suppliers as a structural design weakness rather than isolated component failure.

Symptoms to notice

Hard or extended cranking when hot
Metallic knocking at idle that clears with revs
Black smoke from exhaust under acceleration
Check Injection warning light illuminated

What to check

Cold-start and warm the engine fully, then listen for metallic tapping at idle. Check for black exhaust smoke under load. Ask for written service history including fuel filter change intervals — blocked fuel filter accelerates injector wear. If a workshop inspection is possible: Connect diagnostic scanner and read injector balance rates and any P0200-P0206 fault codes.

Where to look: Top of engine, mounted on common rail fuel rail

Parts involved: Fuel rail, Fuel injector.

Ask the seller

“Have the injectors been tested or replaced, and at what mileage?”
“Has a check engine or check injection warning ever appeared?”
“Is the car used mainly for short city trips or regular highway driving?”

04K9K 1.5 dCi DPF Blockage from Urban Use

Check DPF differential pressure sensor live data.diesel2009–2019EngineCan't confirm for this car$350–$2,200

CommonEngine $350–$2,200 to fix

Can't confirm for this car

The diesel particulate filter on K9K-equipped Clio models requires periodic passive regeneration at sustained highway speeds above 60 km/h for 20–30 minutes. Vehicles used predominantly for short urban trips under 15 km cannot complete regeneration, causing progressive soot accumulation. A fully blocked DPF triggers limp mode, and if ignored, the resulting exhaust backpressure can damage the turbocharger and EGR valve, significantly escalating repair costs.

Symptoms to notice

DPF warning light illuminated on dashboard
Loss of power and entry into limp mode
Increased fuel consumption
Cooling fans running after engine shutdown during failed regeneration

What to check

Check DPF differential pressure sensor live data.
Ask the owner about typical journey length and whether the DPF light has previously illuminated.
Check exhaust for excessive soot output at startup.
If a workshop inspection is possible: Connect diagnostic scanner and read DPF soot load percentage — above 70% is high risk.

Where to look: Exhaust system underfloor, after catalytic converter

Parts involved: Diesel particulate filter.

Ask the seller

“Is this car used mainly for short city trips or regular highway driving?”
“Has the DPF warning light ever come on?”
“Has the DPF been chemically cleaned or replaced?”

05EDC Dual-Clutch Gearbox Cold Shudder and Clutch Pack Wear

Test drive from cold — drive at walking pace in a car park and assess smoothness.petrol2012–2019TransmissionCan't confirm for this car$600–$2,800

CommonTransmission $600–$2,800 to fix

Can't confirm for this car

The EDC (Efficient Dual Clutch) 6-speed dual-clutch transmission fitted to Clio IV models with TCe engines is known for shuddering and juddering during low-speed manoeuvring in cold conditions. The wet dual-clutch pack wears over time, and clutch adaptation parameters drift, causing rough engagement. In colder climates — including NZ winters — the issue is amplified. Clutch replacement or TCU adaptation reset is required; replacement clutch packs are costly. The EDC is fundamentally unsuited to stop-start urban use over extended periods.

Symptoms to notice

Shuddering or juddering from 0–20 km/h especially when cold
Creeping or stalling in traffic at low throttle
Clunky engagement moving from Park to Drive
Vibration through floor when pulling away slowly
Delayed or hesitant response to throttle from rest

What to check

Test drive from cold — drive at walking pace in a car park and assess smoothness.
Try creeping in traffic.
A healthy EDC should feel smooth at all temperatures.
Check for any dealer or workshop TCU adaptation history.
Confirm clutch fluid has been serviced.

Where to look: EDC transmission unit and clutch pack, front of vehicle under bonnet

Parts involved: Clutch.

Ask the seller

“Does the gearbox shudder or judder when pulling away in traffic?”
“Has the EDC clutch pack or fluid been inspected or replaced?”
“Has the TCU been reset or adapted by a dealer?”

Other Renault Lutecia engines and years4 documented issues that do not apply to the one you picked.

Engine, transmission & cooling2

01H4D 1.0 TCe Timing Chain Rattle on Cold Start

Start engine from cold and listen for chain rattle from the front-top of the engine.petrol2019 onwardEngineDoes not apply$900–$3,200

OccasionalEngine $900–$3,200 to fix

Does not apply

The H4D 1.0 three-cylinder turbocharged engine fitted to Clio V uses a timing chain rather than the belt-in-oil design of its predecessor, but the chain tensioner and guides are sensitive to low oil pressure during cold starts. A characteristic rattle on cold start indicates chain slack before oil pressure builds. Continued driving with chain rattle leads to chain stretch, timing variance, and ultimately chain jump causing serious engine damage. The issue is worsened by infrequent oil changes or low-viscosity oil use.

Symptoms to notice

Rattle from engine top-end for several seconds on cold start
Rattle worsens in cold weather or after car sits overnight
Chain noise that diminishes once oil pressure builds
Rough idle on cold start accompanied by chain noise
Engine warning light in advanced cases of chain stretch

What to check

Start engine from cold and listen for chain rattle from the front-top of the engine. Noise should disappear within 5 seconds if tensioner is healthy. Check oil service history — irregular servicing is a strong risk indicator. If a workshop inspection is possible: A diagnostic scan may reveal VVT or timing deviation codes.

Where to look: Timing chain and tensioner, top-front of engine

Parts involved: Timing chain.

Ask the seller

“Does the engine make a rattling noise for a few seconds on cold start?”
“How regularly has the oil been changed and what oil specification was used?”
“Has any dealer or mechanic mentioned the timing chain tensioner?”

02K9K 1.5 dCi EGR Valve Carbon Seizure

Check for black smoke at idle with engine warm.diesel2001–2013EngineDoes not apply$350–$900

Very commonEngine $350–$900 to fix

Does not apply

The Renault-Nissan K9K 1.5 dCi diesel engine in Clio II and III diesel variants is widely documented for EGR valve seizure caused by carbon deposit buildup on the valve seat and bore. A stuck-open EGR causes rough idle, limp mode, and black smoke. The inlet manifold typically requires removal and decarbonisation at the same service. Confirmed across multiple NZ and Australian independent diesel workshops as a routine high-mileage failure.

Symptoms to notice

Rough or hunting idle at operating temperature
Black smoke from exhaust at idle or light throttle
Limp mode or reduced power warning light
P0400 or P0401 EGR flow fault code

What to check

Check for black smoke at idle with engine warm.
Scan for EGR fault codes.
Inspect air intake tract and inlet manifold ports for heavy carbon deposit buildup.
Test EGR valve movement if accessible.

Where to look: Inlet manifold, upper engine — EGR valve mounted between exhaust and intake

Parts involved: EGR valve.

Ask the seller

“Has the EGR valve been cleaned or replaced?”
“Does the car mostly do short trips or highway running?”
“Has it ever gone into limp mode or shown an engine warning?”

Electrical2

01E-TECH Hybrid High-Voltage Battery Module Cell Failure

Request a hybrid system diagnostic scan and review for any stored battery fault codes.hybrid2019 onwardElectricalDoes not apply$2,000–$7,000

OccasionalElectrical $2,000–$7,000 to fix

Does not apply

The Clio V E-TECH full hybrid uses a Renault-proprietary high-voltage battery pack composed of multiple cell modules. Individual cell module failures cause the system to reduce available power or disable hybrid operation entirely, defaulting to conventional engine use only and generating fault codes. In more severe cases the battery management system isolates the pack, requiring specialist diagnosis and module replacement. This is a documented issue in European markets and appears on early Clio V E-TECH examples now entering the NZ used market as grey imports.

Symptoms to notice

Hybrid system warning light on dash
Loss of EV mode or reduced hybrid power
Car running exclusively on petrol with battery icon showing fault
Reduced fuel economy compared to quoted figures
Fault codes referencing battery module or cell voltage imbalance

What to check

Request a hybrid system diagnostic scan and review for any stored battery fault codes.
Verify the hybrid battery temperature and voltage readouts are within range.
Check battery cooling vents are clear.
Ask whether the car has been back to a Renault dealer for any battery-related warranty work.

Where to look: High-voltage hybrid battery under rear seat or boot floor

Ask the seller

“Has the hybrid system warning light appeared and what was the diagnosis?”
“Has the car been to a Renault dealer or hybrid specialist for battery inspection?”
“Is the fuel economy consistent with the car's rated hybrid figures?”

02Electric Power Steering Column Motor Failure

Switch on ignition and check for EPS warning light.petrol2005–2012ElectricalDoes not apply$900–$2,200

CommonElectrical $900–$2,200 to fix

Does not apply

Clio III models with electric power steering are prone to failure of the column-mounted assist motor and its control module. Loss of power assistance occurs suddenly, leaving full manual steering load on the driver. The fault is documented in Renault technical service notes and is a frequent WOF rejection item in NZ. The column assembly is not field-serviceable; full replacement is typically required.

Symptoms to notice

Sudden loss of power steering assistance, especially at low speed or parking
EPS warning light on instrument cluster
Intermittent heavy steering before permanent failure
C-series fault codes stored in steering control module

What to check

Switch on ignition and check for EPS warning light. Drive at parking speed and confirm consistent assist. If a workshop inspection is possible: Connect diagnostic tool and read steering module for stored fault codes.

Where to look: Steering column assembly, beneath dashboard

Parts involved: Steering rack.

Ask the seller

“Has the steering ever felt heavy or logged a fault?”
“Has the steering column or EPS module been replaced?”
“Are there any current warning lights on the dashboard?”

What these repairs cost on other cars

Some of the Renault Lutecia’s documented faults are repairs other models share. Each page lists the documented NZ cost for every model it affects.

Other Renault models

Renault Megane27 documented faults Renault Koleos17 documented faults Renault Clio15 documented faults Renault Laguna8 documented faults Renault Captur6 documented faults Renault Scenic6 documented faults

Renault Lutecia buyer questions

Is the Renault Lutecia reliable?

Like any used car, it depends on the specific example and its service history. Across the 11 documented faults for the Renault Lutecia, the recurring problem areas are electrical, engine, and transmission. A Renault Lutecia with a full service history and no signs of the issues listed on this page can be a sound buy but each one needs to be checked individually before you commit.

What are the most common problems with a used Renault Lutecia?

We've catalogued 11 known faults for the Renault Lutecia, covering electrical, engine, and transmission. All 11 are written out in full on this page, with the symptoms to notice, what to inspect, and typical repair costs for each. Free to read, no account needed.

How much do repairs cost on a Renault Lutecia?

Most single repairs on the Renault Lutecia fall between $600–$2,800 at NZ independent-workshop rates. Some of the 11 documented faults cost less and a few cost considerably more, and no one car needs them all. Knowing which ones to look for before you view is what lets you negotiate the price down or walk away.

Should I get a pre-purchase inspection on a Renault Lutecia?

Yes. A Renault Lutecia inspection focused on its known weak points is the single best way to avoid an expensive mistake. KickTyres gives you a guided, model-specific inspection plus a market valuation and negotiation figure for $24.90 far less than the cost of missing one of the faults on this page.