Skip to content
KickTyres
Toyota1980–2021 Critical issues documented

Toyota Land Cruiser 100: common faults & what to check

The 100 is the Toyota Land Cruiser built 2000–2007. It was sold here with the 4.2L diesel (1HD-FTE), 4.2L diesel (1HZ), and 4.7L petrol (2UZ-FE). Of the 42 faults documented for the Land Cruiser, 22 apply to this generation, each with its symptoms, what to inspect and a typical repair cost. Free, no account needed.

Check this exact Toyota Land Cruiser

  • Odometer history
  • Money owing
  • Reported stolen
  • Ownership history
  • Official NZ vehicle register data
  • NZ owned and operated

Type the plate for the free basics. The full record is a paid check from $13.49, one car at a time, no subscription.

No NZ plate yet, or buying in Australia? Pick the generation and engine and start a free check below. New to KickTyres? How the check works →

42

Documented faults

Critical

Most serious

$800–$2,800

Typical repair

27

Service milestones

You're looking at the 100

3 engine variants are documented for this generation. Pick yours to narrow further, or keep reading for the generation as a whole.

Choose a different generation

Now narrow it to the engine

A 1.8 and a 2.4 of the same car do not fail the same way, so the faults below narrow to the engine as well as the year. Free, no account needed.

A 2000 Toyota Land Cruiser is the 100 generation (2000 to 2007).

Start your free check on this Toyota Land Cruiser

No plate needed. You get the risk score, the buyer's checklist and the guided inspection for the exact car you picked above — not the whole nameplate.

Toyota Land Cruiser 100Engine not picked yet

Pick the engine above first: the Land Cruiser came with 3, and without it the report has to show all of their faults. Pick the engine

Free. The paid plate check is separate, and stays optional.

Can't confirm for this car

Toyota Land Cruiser · 2000

Narrowed to the year. No engine is recorded for this vehicle. Pick an engine to see which faults apply.

Tell us the engine, or check the engine code on the car, before relying on this.

  • No engine is recorded for this vehicle.

matched on year only

What to look out for

The checks worth doing on a Toyota Land Cruiser before you hand over any money. Every documented fault is listed below, each with its own page.

  • Serious issue

    Observe vehicle ride height with all four corners — they should be level and at normal height.

    See why

    Active Height Control (AHC) Hydraulic Suspension System Failure

    The optional Active Height Control (AHC) hydraulic suspension system fitted to many 100 series Land Cruisers is one of the most notorious and expensive failure points on the platform. The system uses a hydraulic pump, nitrogen-filled accumulators at each corner, steel hard lines, rubber hoses, and height sensors. Accumulators lose nitrogen charge over 10-15 years, causing the vehicle to sag to the bump stops overnight. The hydraulic pump, solenoids, and height sensors also fail independently. Complete system overhaul is extremely costly; many owners convert to aftermarket coilover suspension. Failure is considered nearly universal on unrestored high-mileage examples.

    What you would notice

    • Vehicle sags to the ground or sits very low when parked overnight
    • AHC warning light on the instrument cluster
    • Incorrect or uneven ride height corner-to-corner
    • Hydraulic pump running continuously or failing to activate
    • Slow or non-functional ride height adjustment

    Typically $4,000–$15,000 to put right.

  • Serious issue

    With the front wheels on the ground, attempt to rock each front wheel at the 12 and 6 o'clock positions to detect vertical play.

    See why

    Front Lower Ball Joint and King Pin Wear

    The 80 Series LandCruiser uses a solid front axle with king pins and trunnion bearings at each knuckle, while the 100 Series uses independent double-wishbone suspension with pressed-in lower ball joints. On the 80 Series, the king pins and their associated thrust bearings wear under the combination of heavy vehicle weight, off-road articulation, and high steering loads, allowing the steering knuckle to develop lateral play. On the 100 Series, the lower ball joint boot tears from flex and contamination, accelerating the ball joint wear rate. In both configurations, worn components create a handling and safety risk because the front wheels can develop camber wander and in extreme cases the joint can separate.

    What you would notice

    • Clunking or knocking from the front suspension over bumps or during low-speed steering inputs
    • Steering wander or vagueness requiring constant correction on straight roads
    • Uneven front tyre wear, particularly feathering or inside-edge wear, caused by geometry change under load

    Typically $600–$2,800 to put right.

  • Costly issue

    Run fingers along the underside of all door sills — flex the metal to feel for weakness.

    See why

    Wheel Arch, Sill, and Lower Body Rust on JDM and AU Imports

    Land Cruiser 100 series vehicles imported to New Zealand and Australia (now 17-27 years old) are susceptible to rust in the rear wheel arches, lower door sills, and floor sections. Mud and road debris pack into the inner wheel arch areas, retaining moisture against the steel. Sill rust is easily hidden under rubber trim and can be structurally significant. NZ coastal environments accelerate corrosion on vehicles with degraded undercoating. Lower tailgate corners, the spare wheel carrier mounting, and the rear floor pan seams are also documented rust locations.

    What you would notice

    • Rust bubbling or paint lifting at wheel arch lips or lower sills
    • Rust staining on lower bodywork panels
    • Soft or flexible metal when pressed at sill areas
    • Visible rust holes in inner wheel arch flanges
    • Rust around spare wheel carrier mounting bolts

    Typically $1,000–$8,000 to put right.

  • Costly issue

    Open the tailgate and run a finger along its bottom inner seam.

    See why

    Rust in tailgate, rear quarters, sills and chassis — NZ coastal / beach-launched examples

    100-series Land Cruisers in NZ are frequently used for boat launching and beach driving, and rust takes hold in the lower tailgate seam, rear wheel arches, sills, door bottoms and on the chassis rails and rear crossmember. Surface rust is manageable, but rot in the tailgate seam or chassis is expensive and can be a WoF failure. Many JDM imports also arrive with underbody corrosion from Japanese road salt.

    What you would notice

    • Bubbling paint along the bottom tailgate seam and rear arches
    • Flaking scale on chassis rails and rear crossmember
    • Damp or musty smell in the cargo area
    • Corroded brake and fuel lines under the body

    Typically $500–$5,000 to put right.

  • Costly issue

    With the engine running and the vehicle stationary, turn the steering wheel to full lock in each direction and listen for whining from the pump.

    See why

    Power Steering Pump Bearing and Vane Wear

    The hydraulic power steering pump on the 100 series is prone to bearing failure and internal vane wear at high mileage. The characteristic symptom is a whining or groaning noise that worsens at full steering lock. As the pump deteriorates, steering effort increases and fluid pressure becomes inconsistent. Fluid leaks from the pump shaft seal are also common as bearing wear allows shaft play. Replacement is moderately priced but labour to access the pump requires removing ancillary components. Common on examples over 200,000 km.

    What you would notice

    • Whining or groaning from the engine bay, louder at full steering lock
    • Increased steering effort, especially at low speed
    • Power steering fluid leaks or residue around the pump
    • Inconsistent or vague steering feel

    Typically $600–$1,800 to put right.

  • Costly issue

    Inspect the entire length of each spring leaf for visible cracks, particularly at the spring eyes, centre bolt boss, and within 150mm of the eye.

    See why

    Rear Leaf Spring Main Leaf Fatigue Crack

    Both the 80 and 100 Series LandCruiser use multi-leaf rear spring packs designed for heavy payloads and towing. Under sustained high-load operation — extended towing at maximum GVM, overloading, or repeated heavy off-road impacts — the main leaf or second leaf is subject to fatigue cracking, typically initiating near the spring eye or at the centre bolt boss where bending stress concentration is highest. Cracks often propagate gradually and are hidden between spring leaves, making visual inspection difficult without separating the pack. A broken main leaf causes immediate and significant suspension geometry change, potentially causing the axle to shift laterally and the vehicle to become difficult to control.

    What you would notice

    • Visible crack or break in one or more leaves of the rear spring pack, sometimes only apparent after leaf separation
    • Sudden asymmetric rear ride height drop, with one side sitting notably lower than the other under no load
    • Rear axle lateral shift or the vehicle tracking crooked under braking or acceleration

    Typically $700–$1,800 to put right.

Toyota Land Cruiser service schedule

The 2 engines a 2000 Toyota Land Cruiser was sold with, each with its own intervals. Pick your engine above to narrow this to one. These are the model’s intervals — the car’s own service book is the only thing that can tell you what has actually been done to it.

Land Cruiser 100 Series (Facelift) · 2000–2007 · 4.7L (2UZ-FE) - V8 Petrol VX/Sahara

Petrol

Due by distance

  1. 150,000 km

    Cooling system parts, the radiator and fan clutch especially, tend to start showing their age around here.

  2. 200,000 km

    This is the point the timing belt and water pump should already have been replaced, so check the logbook says so.

  3. 250,000 km

    Suspension bushings and ball joints can feel tired by now, which blunts the steering on these heavy wagons.

Land Cruiser 100 Series (Facelift) · 2000–2007 · 4.2L (1HD-FTE) - Turbo Diesel GX/VX/Sahara

Diesel

Due by distance

  1. 150,000 km

    Time for a major service with a cooling system refresh and a check of the steering components.

  2. 200,000 km

    The timing belt is due for replacement, and the fuel injectors should be checked for efficiency.

  3. 300,000 km

    Suspension bushes and shock absorbers often reach the end of their life here and may need replacing to keep the ride right.

See all 22 issues for this oneDocumented for the exact year and engine you picked, including 8 rated critical.
Body, brakes, suspension & interior2 critical7

01Active Height Control (AHC) Hydraulic Suspension System Failure

Observe vehicle ride height with all four corners — they should be level and at normal height.1998–2007Suspension
Very commonSuspension $4,000–$15,000 to fix

The optional Active Height Control (AHC) hydraulic suspension system fitted to many 100 series Land Cruisers is one of the most notorious and expensive failure points on the platform. The system uses a hydraulic pump, nitrogen-filled accumulators at each corner, steel hard lines, rubber hoses, and height sensors. Accumulators lose nitrogen charge over 10-15 years, causing the vehicle to sag to the bump stops overnight. The hydraulic pump, solenoids, and height sensors also fail independently. Complete system overhaul is extremely costly; many owners convert to aftermarket coilover suspension. Failure is considered nearly universal on unrestored high-mileage examples.

Symptoms to notice

  • Vehicle sags to the ground or sits very low when parked overnight
  • AHC warning light on the instrument cluster
  • Incorrect or uneven ride height corner-to-corner
  • Hydraulic pump running continuously or failing to activate
  • Slow or non-functional ride height adjustment

What to check

  1. Observe vehicle ride height with all four corners — they should be level and at normal height.
  2. Look under the vehicle for hydraulic lines showing rust, weeping, or damage.
  3. Ask if the vehicle maintains its height after sitting overnight.
  4. Check the instrument cluster for any AHC warning light.
  5. Test the height adjustment function via the driver's controls if present.

Where to look: All four corners of the vehicle (accumulators at each wheel), hydraulic pump in the engine bay, height sensors mounted at suspension control arms

Ask the seller

  • “Does the vehicle maintain its ride height when parked overnight?”
  • “Has the AHC system been serviced, rebuilt, or converted to coilovers?”
  • “Are there any suspension or AHC warning lights currently or historically?”
  • “Has the hydraulic pump or any accumulator been replaced?”

02Front Lower Ball Joint and King Pin Wear

With the front wheels on the ground, attempt to rock each front wheel at the 12 and 6 o'clock positions to detect vertical play.1990–2007SuspensionRead the full fault: symptoms, where to look, what to ask the seller

03Wheel Arch, Sill, and Lower Body Rust on JDM and AU Imports

Run fingers along the underside of all door sills — flex the metal to feel for weakness.1998–2007Body & Rust
CommonBody & Rust $1,000–$8,000 to fix

Land Cruiser 100 series vehicles imported to New Zealand and Australia (now 17-27 years old) are susceptible to rust in the rear wheel arches, lower door sills, and floor sections. Mud and road debris pack into the inner wheel arch areas, retaining moisture against the steel. Sill rust is easily hidden under rubber trim and can be structurally significant. NZ coastal environments accelerate corrosion on vehicles with degraded undercoating. Lower tailgate corners, the spare wheel carrier mounting, and the rear floor pan seams are also documented rust locations.

Symptoms to notice

  • Rust bubbling or paint lifting at wheel arch lips or lower sills
  • Rust staining on lower bodywork panels
  • Soft or flexible metal when pressed at sill areas
  • Visible rust holes in inner wheel arch flanges
  • Rust around spare wheel carrier mounting bolts

What to check

  1. Run fingers along the underside of all door sills — flex the metal to feel for weakness.
  2. Remove rubber sill trim if fitted.
  3. Crouch down and inspect all four wheel arch lips for rust bubbling at the seam.
  4. Inspect the floor under the rear cargo area and around the spare wheel well.
  5. Check lower tailgate corners.

Where to look: Lower door sills, rear wheel arch lips and seams, rear floor pan, lower tailgate corners, spare wheel carrier mounting points

Parts involved: Body corrosion.

Ask the seller

  • “Has the vehicle had any rust treatment, panel repairs, or body filler work?”
  • “Is there any rust under the sill trim?”
  • “Has the undercarriage been resprayed or treated with any rust-proofing product?”

04Rust in tailgate, rear quarters, sills and chassis — NZ coastal / beach-launched examples

Open the tailgate and run a finger along its bottom inner seam.1998–2007Body & RustRead the full fault: symptoms, where to look, what to ask the seller

05Power Steering Pump Bearing and Vane Wear

With the engine running and the vehicle stationary, turn the steering wheel to full lock in each direction and listen for whining from the pump.1998–2007Suspension
CommonSuspension $600–$1,800 to fix

The hydraulic power steering pump on the 100 series is prone to bearing failure and internal vane wear at high mileage. The characteristic symptom is a whining or groaning noise that worsens at full steering lock. As the pump deteriorates, steering effort increases and fluid pressure becomes inconsistent. Fluid leaks from the pump shaft seal are also common as bearing wear allows shaft play. Replacement is moderately priced but labour to access the pump requires removing ancillary components. Common on examples over 200,000 km.

Symptoms to notice

  • Whining or groaning from the engine bay, louder at full steering lock
  • Increased steering effort, especially at low speed
  • Power steering fluid leaks or residue around the pump
  • Inconsistent or vague steering feel

What to check

  1. With the engine running and the vehicle stationary, turn the steering wheel to full lock in each direction and listen for whining from the pump.
  2. Check the power steering fluid reservoir level and condition — dark or burnt-smelling fluid indicates internal wear.
  3. Inspect the pump mounting area for fluid residue or drips.

Where to look: Engine bay — power steering pump driven by the accessory belt, typically on the passenger side of the engine

Parts involved: Steering rack.

Ask the seller

  • “Has the power steering pump been replaced?”
  • “Is there any whining or groaning when turning at low speed?”
  • “When was the power steering fluid last changed?”

06Rear Leaf Spring Main Leaf Fatigue Crack

Inspect the entire length of each spring leaf for visible cracks, particularly at the spring eyes, centre bolt boss, and within 150mm of the eye.1990–2007Suspension
OccasionalSuspension $700–$1,800 to fix

Both the 80 and 100 Series LandCruiser use multi-leaf rear spring packs designed for heavy payloads and towing. Under sustained high-load operation — extended towing at maximum GVM, overloading, or repeated heavy off-road impacts — the main leaf or second leaf is subject to fatigue cracking, typically initiating near the spring eye or at the centre bolt boss where bending stress concentration is highest. Cracks often propagate gradually and are hidden between spring leaves, making visual inspection difficult without separating the pack. A broken main leaf causes immediate and significant suspension geometry change, potentially causing the axle to shift laterally and the vehicle to become difficult to control.

Symptoms to notice

  • Visible crack or break in one or more leaves of the rear spring pack, sometimes only apparent after leaf separation
  • Sudden asymmetric rear ride height drop, with one side sitting notably lower than the other under no load
  • Rear axle lateral shift or the vehicle tracking crooked under braking or acceleration

What to check

  1. Inspect the entire length of each spring leaf for visible cracks, particularly at the spring eyes, centre bolt boss, and within 150mm of the eye.
  2. Separate the spring pack leaves where possible to check hidden surfaces.
  3. Look for disturbed rust patterns or fresh metal exposure indicating crack propagation.
  4. Check for unequal rear ride height suggesting a broken leaf allowing pack collapse.
  5. Inspect U-bolt condition as loose U-bolts accelerate spring movement and fatigue.

Where to look: Rear axle leaf spring pack, both driver and passenger sides, at the main and second leaf

Parts involved: Rear leaf spring.

Ask the seller

  • “Has the vehicle been used for regular towing at or near maximum GVM?”
  • “Have the rear springs or U-bolts ever been replaced?”
  • “Has the vehicle ever been overloaded or used for commercial freight work?”

07Brake Caliper Guide Pin Seizure

1990–2007Brakes
Very commonBrakes $250–$750 to fix

The sliding brake calipers on both the 80 and 100 Series rely on two hardened steel guide pins coated in rubber boots and high-temperature grease to allow the caliper body to slide laterally as the pads wear. The guide pin boots perish with age and allow water, road salt, and mud to contaminate and wash out the grease, causing the pins to corrode and seize within their bores. A seized guide pin prevents the caliper from retracting after brake release, causing continuous pad drag on the disc, heat build-up, accelerated pad and rotor wear on one side, and in severe cases brake fluid boiling or a stuck brake. The rear calipers are particularly vulnerable due to their proximity to road spray and the reduced brake heat that would otherwise evaporate moisture.

Symptoms to notice

  • Vehicle pulling to one side under braking, caused by unequal braking force from a dragging caliper on one side
  • One wheel significantly hotter than the opposite side after a normal drive, indicating continuous caliper drag
  • Uneven brake pad wear with the inner or outer pad substantially thinner than its counterpart on the same corner

What to check

After a normal drive, carefully place a hand near each wheel centre (not touching the disc) to compare temperatures — a seized caliper will produce significantly more heat on the affected wheel. Inspect the guide pin rubber boots for cracking, tears, or collapse. Look for uneven pad thickness between inner and outer pads, and scoring on one face of the brake disc. If a workshop inspection is possible: Remove the caliper and attempt to slide each guide pin by hand; it should move smoothly with finger pressure.

Where to look: Front and rear brake caliper guide pin bores, particularly rear calipers on both 80 and 100 Series

Parts involved: Brake disc and pads.

Ask the seller

  • “When were the brake calipers last serviced, including guide pin cleaning and re-greasing?”
  • “Has the vehicle ever pulled to one side under braking?”
  • “Have the brake pads worn unevenly or needed replacing at different intervals on each side?”
Depends on the exact engine — 15 moreDocumented for a specific engine we could not confirm from what you picked. Check the engine code on the car.
Engine, transmission & cooling11

011HD-FTE 4.2 Turbo Diesel Timing Belt Failure

Obtain full service history and verify timing belt replacement date and odometer reading.diesel1998–2007EngineRead the full fault: symptoms, where to look, what to ask the seller

02Injection Pump Plunger and Barrel Wear (1HD-FTE Denso VE Pump)

Start from cold and observe idle quality, then repeat after a full warm-up cycle.diesel1998–2007EngineRead the full fault: symptoms, where to look, what to ask the seller

03Head Gasket Failure Due to Head Bolt Torque Loss (1HD-FTE 4.2L)

Inspect the coolant overflow tank for oil contamination or bubbling.diesel1998–2007EngineRead the full fault: symptoms, where to look, what to ask the seller

04Timing Belt Failure Risk — Interference Engine (2UZ-FE 4.7L V8)

Ask for documented service records showing timing belt replacement.petrol1998–2007Engine
OccasionalEngine $800–$1,800 to fix

Can't confirm for this car

The 2UZ-FE 4.7L V8 drives its camshafts via a rubber timing belt, not a chain. This is an interference engine — belt failure at speed causes immediate piston-to-valve contact and catastrophic engine destruction. Toyota specifies replacement at 100,000 km or 10 years, but many imported examples arrive in NZ/AU with unknown belt history. Water pump failure is a secondary failure mode that can destroy the belt simultaneously. A complete belt service including tensioner, idler pulleys, and water pump is mandatory at purchase if history is not documented.

Symptoms to notice

  • No warning prior to failure — sudden engine stop
  • Engine cranks but will not start after belt snaps
  • Ticking or rattling from timing cover area if tensioner is weakening
  • Coolant leak from water pump area if water pump is failing

What to check

  1. Ask for documented service records showing timing belt replacement.
  2. Check for a sticker on the timing cover showing last belt date and mileage.
  3. If no documentation is available, budget for immediate replacement at purchase.
  4. Inspect the coolant hose area near the water pump for weeping.

Where to look: Front of engine — timing belt cover on the 4.7L V8, spanning both cam banks

Parts involved: Timing belt.

Ask the seller

  • “When was the timing belt last replaced and at what odometer reading?”
  • “Was the water pump replaced at the same time?”
  • “Were the tensioner and idler pulleys also replaced?”

051HZ timing belt, tensioner and water pump replacement overdue (interference: yes)

Ask for invoices showing the timing belt kit with date and odometer reading.diesel1990–2007EngineRead the full fault: symptoms, where to look, what to ask the seller

061HD-FTE injector and injection pump wear at high mileage

Cold-start the engine yourself (feel the bonnet — it should be cold when you arrive).diesel2000–2007EngineRead the full fault: symptoms, where to look, what to ask the seller

07Valve Stem Seal Deterioration and Oil Consumption (2UZ-FE 4.7L V8)

Start the engine from cold and observe the exhaust for blue smoke.petrol1998–2007Engine
CommonEngine $2,000–$4,500 to fix

Can't confirm for this car

The rubber valve stem seals on the 2UZ-FE V8 harden and shrink with age, allowing engine oil to be drawn past the valve guides and burned during combustion. This produces characteristic blue smoke on cold startup or during the overrun after deceleration. Oil consumption can reach 1 litre per 1,000 km on severely affected engines. The repair requires full cylinder head removal and replacement of all 32 valve stem seals — a labour-intensive job. Very common on examples over 200,000 km, and widely documented across all 2UZ-FE applications.

Symptoms to notice

  • Blue smoke from exhaust on cold startup
  • Blue smoke on deceleration or overrun after sustained speed
  • Engine oil consumption exceeding 500 ml per 1,000 km
  • Oily deposits on spark plugs
  • Oil smell from exhaust

What to check

  1. Start the engine from cold and observe the exhaust for blue smoke.
  2. Blip the throttle after a sustained period of idling and watch for a blue puff.
  3. Check the oil dipstick level and ask the seller how frequently oil is topped up between services.

Where to look: Cylinder heads — valve guides and stem seals across both banks of the V8

Parts involved: Cylinder head.

Ask the seller

  • “How much oil does the engine use between services?”
  • “Has blue smoke ever been noticed on startup or when lifting off the throttle?”
  • “Have the valve stem seals been replaced?”

08Front differential and CV (birfield) wear — weak 2-pinion diff on early 100 series

On the test drive, do slow full-lock circles in both directions in a car park and listen for rhythmic clicking (worn birfields).1998–2007Transmission
OccasionalTransmission $1,200–$4,500 to fix

Can't confirm for this car

Early 100-series front diffs use a 2-pinion centre that can strip ring-and-pinion teeth under shock load (wheel hop, full-lock wheelspin off-road); Toyota moved to a stronger 4-pinion unit later in production but failures are still reported on hard-worked trucks. The front CV joints (birfields) also wear and click on full lock, and perished front diff bushings cause a clunk when shifting between Drive and Reverse. A vehicle that has towed heavily or been off-road most of its life is far more at risk than a suburban one.

Symptoms to notice

  • Clicking or knocking from the front wheels on full-lock turns
  • Clunk from the front when shifting D to R
  • Whine or howl from the front diff at speed
  • Grease sling on the inside of the front wheels from split CV boots

What to check

On the test drive, do slow full-lock circles in both directions in a car park and listen for rhythmic clicking (worn birfields). Shift D-R-D at a stop and feel for a clunk. Look behind each front wheel for grease thrown from split CV boots. Ask a hoist inspection to check front diff oil for metal glitter.

Where to look: Front axle — differential housing and CV joints behind each front wheel

Parts involved: Differential.

Ask the seller

  • “Has the truck been used off-road or for heavy towing?”
  • “Have the CV joints or front diff ever been rebuilt?”
  • “When was the front diff oil last changed?”

09Intercooler Hose Cracking and Boost Leaks (1HD-FTE 4.2L Turbo)

With the engine cold, inspect all large rubber hoses between the turbocharger, intercooler, and intake manifold.diesel1998–2007EngineRead the full fault: symptoms, where to look, what to ask the seller

10Secondary Air Injection Pump Failure (2UZ-FE 4.7L V8)

Ask the seller if the check engine light has been on.petrol1998–2007Engine
Very commonEngine $400–$1,200 to fix

Can't confirm for this car

The 2UZ-FE uses a secondary air injection (SAI) system to reduce cold-start emissions. The electric air pump is prone to failure due to moisture ingestion and motor burnout. When the pump fails it triggers diagnostic codes (typically P0410 or P0411) and illuminates the check engine light, sometimes accompanied by VSC and traction control warnings due to shared CAN bus diagnostics. This fault is extremely common on imported 100 series V8s and affects the majority of high-mileage examples. The pump body, reed check valves, and associated pressure hoses all deteriorate with age.

Symptoms to notice

  • Check engine light (MIL) illuminated
  • VSC or traction control warning light on
  • DTCs P0410 or P0411 stored in ECU
  • Rattling noise at cold start from failed pump motor
  • Slightly rough cold idle in some cases

What to check

  1. Ask the seller if the check engine light has been on.
  2. Inspect the air injection pump (black cylindrical unit in the engine bay) for signs of rust, water damage, or missing hoses.
  3. If a workshop inspection is possible: Connect an OBD-II scanner and read fault codes — P0410 and P0411 are definitive for this failure.

Where to look: Engine bay — secondary air injection pump mounted near the firewall or inner guard, with hoses running to the exhaust manifolds

Parts involved: High-pressure fuel pump.

Ask the seller

  • “Has the check engine light been on? What codes were stored?”
  • “Has the secondary air injection pump been replaced or deleted?”
  • “Does the VSC warning light illuminate?”

11A343F / A750F Automatic Transmission Clutch Pack Wear and Solenoid Faults

Check the transmission dipstick — smell the fluid for burning and examine colour (should be red; dark brown or black indicates breakdown).1998–2007Transmission
OccasionalTransmission $3,500–$9,000 to fix

Can't confirm for this car

The 100 series uses a Toyota A343F (4-speed, earlier models) or A750F (5-speed, later models) automatic transmission. Both units suffer from clutch pack wear and torque converter slip on high-mileage vehicles, particularly those used for towing or repeated off-road use. The A750F additionally develops shift solenoid faults that trigger transmission warning lights. Fluid degradation accelerates wear — the factory drain interval is inadequate for hard-use conditions. Rebuild is expensive and requires specialist transmission experience.

Symptoms to notice

  • Slipping between gears or delayed engagement from park or reverse
  • Transmission warning light on instrument cluster
  • Harsh, jerky, or hunting gear changes
  • Transmission fluid dark, burnt-smelling, or contaminated with metallic particles
  • Late upshifts or failure to shift under load

What to check

Check the transmission dipstick — smell the fluid for burning and examine colour (should be red; dark brown or black indicates breakdown). Look for fluid leaks around the transmission pan, tail shaft, or cooler lines. During the test drive, note engagement quality from park and any slipping under load. If a workshop inspection is possible: Pull transmission fault codes with a scan tool.

Where to look: Transmission tunnel — automatic gearbox mounted behind the engine, dipstick accessible on the passenger side

Parts involved: Clutch.

Ask the seller

  • “Has the transmission fluid been serviced and at what intervals?”
  • “Has the vehicle ever slipped between gears or hesitated on engagement?”
  • “Has the transmission been rebuilt or replaced?”
  • “Has the vehicle been used for towing or regular off-road use?”
Body, brakes, suspension & interior4

01Brake Booster Vacuum Pump Failure and Hose Deterioration (1HD-FTE Diesel)

Diesel engines produce no intake manifold vacuum, so the 1HD-FTE relies on a dedicated camshaft-driven vacuum pump to operate the brake booster.diesel1998–2007Brakes
OccasionalBrakes $500–$1,500 to fix

Can't confirm for this car

Diesel engines produce no intake manifold vacuum, so the 1HD-FTE relies on a dedicated camshaft-driven vacuum pump to operate the brake booster. The pump vanes and internal seals wear over time, reducing or eliminating brake assist. A failed pump results in a significantly harder brake pedal requiring much greater force to stop — a serious safety hazard. The rubber vacuum hose from the pump to the booster also cracks with age. This issue is documented across all 1HD-FTE diesel applications and is frequently overlooked until brake pedal feel has already deteriorated.

Symptoms to notice

  • Hard brake pedal requiring excessive force
  • Increased stopping distance
  • Hissing sound near the brake booster when the pedal is depressed
  • Brake pedal feel changes between engine running and engine off

What to check

Pump the brake pedal 5-6 times with the engine off to exhaust any stored vacuum, then hold the pedal depressed and start the engine — the pedal should drop slightly as vacuum assist engages. If the pedal does not drop, vacuum assist is absent. Inspect the vacuum hose from the pump to the brake booster for cracks or brittleness.

Where to look: Vacuum pump mounted on the rear of the engine block (camshaft-driven), vacuum hose running forward to the brake booster on the firewall

Parts involved: Intake manifold.

Ask the seller

  • “Has the brake vacuum pump been replaced or serviced?”
  • “Has the brake pedal ever felt unusually hard or required more force than normal?”
  • “Has the vacuum hose to the brake booster been replaced?”

02Steering rack wear and leaks (100 series rack-and-pinion)

Check the power-steering reservoir level and whether the fluid is dark.1998–2007Suspension
CommonSuspension $1,500–$2,800 to fix

Can't confirm for this car

The 100 series switched to rack-and-pinion steering, and the rack's internal seals perish with age while oversized tyres and off-road use stress the rack itself. Result is power-steering fluid leaks, notchy or loose steering, and eventually a reconditioned rack. Most NZ examples are now 20+ years old, so an original rack is living on borrowed time.

Symptoms to notice

  • Power steering fluid drips under the front axle line
  • Groaning pump / low fluid reservoir
  • Play or clunk in the steering over bumps
  • Uneven front tyre wear

What to check

  1. Check the power-steering reservoir level and whether the fluid is dark.
  2. Look at the rack boots under the front for fluid weeping.
  3. With the engine on, rock the wheel lock to lock at a stop and listen for knocks.
  4. Note if the truck runs oversized tyres — that accelerates rack wear.

Where to look: Steering rack across the front axle, behind the front diff; reservoir in the engine bay

Parts involved: Steering rack, Differential.

Ask the seller

  • “Has the steering rack ever been replaced or resealed?”
  • “How often does it need power-steering fluid topped up?”
  • “What size tyres has it run?”

03Front brake disc bolt recall (100 series Land Cruiser, 1998-2005)

On the test drive listen for a rattle or clunk from the front wheels over bumps and under firm braking.1998–2005Brakes
CommonBrakes $0 to fix

Can't confirm for this car

100 and 105 series Land Cruisers built from late 1997 to December 2005 (FZJ105, HZJ105, UZJ100 and HDJ100) were recalled (PRA 2007/9087) because the bolts holding the front brake discs can loosen after hard braking in tough conditions, causing a rattle and risking brake damage. The fix is free at a Toyota dealer. This was an Australian recall; Japanese-import 100 series cars were not named in it, so ask a Toyota dealer to check the VIN.

Symptoms to notice

  • Rattle or clunk from the front wheels
  • Rattle when braking over rough ground

What to check

On the test drive listen for a rattle or clunk from the front wheels over bumps and under firm braking. Ask the seller for the service history and look for a dealer invoice or service stamp showing recall PRA 2007/9087 (brake disc bolts) was done. A buyer can also give the VIN to any franchise dealer and ask them to check for open recalls before paying. If a workshop inspection is possible: with the wheels off, check the disc to hub bolts are tight.

Where to look: Front brake discs and hubs

Parts involved: Brake disc and pads.

Ask the seller

  • “Has the brake disc bolt recall been done?”
  • “Is it an NZ new or AU car, or a Japanese import?”

04Spare wheel winch cable recall (100 series Land Cruiser, 1998-2001)

Look under the rear with a phone torch: the spare should sit tight up against the floor.1998–2001Body & Rust
OccasionalBody & Rust $0 to fix

Can't confirm for this car

100 series Land Cruisers built from January 1998 to September 2001 were recalled (PRA 2002/5421) because the cable on the under-floor spare wheel winch can fray with vibration on rough roads, so the spare wheel can drop onto the road. This applies to all engines. The fix is free at a Toyota dealer. This was an Australian recall; Japanese-import 100 series cars were not named in it, so ask a Toyota dealer to check the VIN.

Symptoms to notice

  • Spare wheel hangs low or rattles under the rear

What to check

  1. Look under the rear with a phone torch: the spare should sit tight up against the floor.
  2. Ask the seller for the service history and look for a dealer invoice or service stamp showing recall PRA 2002/5421 (spare wheel winch) was done.
  3. A buyer can also give the VIN to any franchise dealer and ask them to check for open recalls before paying.

Where to look: Under the rear floor, spare wheel carrier

Ask the seller

  • “Has the spare wheel winch recall been done?”
Other Toyota Land Cruiser engines and years20 documented issues that do not apply to the one you picked.
Engine, transmission & cooling15

01Air intake dust ingress ('dusting') on early VDJ200 — poor factory airbox sealing

Undo the airbox clips and wipe a finger inside the clean-side outlet duct — any grit or dust film after the filter is a red flag.diesel2007–2015Engine
OccasionalEngine $3,000–$15,000 to fix

Does not apply

Early 200-series diesels are notorious in Australasia for dust bypassing the factory airbox and snorkel joins, sandblasting the mass-airflow sensor, turbos and eventually the bores — owners call it 'dusting the engine'. Trucks used on gravel and outback-style roads are most at risk, and a dusted engine means turbo replacement or a full rebuild. Most enthusiast-owned trucks have had the airbox joins sealed and run pre-cleaners; an unmodified high-country farm truck deserves suspicion.

Symptoms to notice

  • Fine dust visible inside the airbox outlet or intake piping (after the filter)
  • Rising oil consumption
  • Turbo whistle or excessive smoke
  • Poor compression test results

What to check

  1. Undo the airbox clips and wipe a finger inside the clean-side outlet duct — any grit or dust film after the filter is a red flag.
  2. Check whether the airbox seams have been silicone-sealed (a good sign the owner knew).
  3. Ask for compression or oil-analysis records on a truck that has lived on gravel.

Where to look: Airbox and intake ducting on the driver's side of the engine bay, plus snorkel joins on the A-pillar

Parts involved: Turbocharger.

Ask the seller

  • “Has it spent its life on gravel or station roads?”
  • “Has the airbox been sealed or a pre-cleaner fitted?”
  • “Has oil consumption ever been an issue?”

02Head Gasket Failure Under Towing Load (1HD-T 4.2L Turbo Diesel)

Check the exhaust for persistent white smoke under hard acceleration.diesel1990–1997EngineRead the full fault: symptoms, where to look, what to ask the seller

031FZ-FE 4.5 Petrol Cracked Cylinder Head and Head Gasket Failure

Conduct a combustion leak (CO2 block) test on the coolant system with the engine at operating temperature.petrol1992–1998EngineRead the full fault: symptoms, where to look, what to ask the seller

041HZ 4.2 Diesel Head Gasket Failure at High Mileage

Remove oil filler cap and inspect for white mayonnaise emulsion.diesel1990–1998EngineRead the full fault: symptoms, where to look, what to ask the seller

05Injection Pump Internal Wear (1HZ 4.2L Naturally Aspirated Diesel)

The 1HZ uses a Bosch VE-type mechanical rotary injection pump that is highly sensitive to fuel quality and contamination.diesel1990–1997EngineRead the full fault: symptoms, where to look, what to ask the seller

06Oil Cooler Failure and Coolant/Oil Cross-Contamination (1HZ 4.2L)

Pull the oil dipstick and examine it for any milky, foamy, or caramel appearance.diesel1990–1997CoolingRead the full fault: symptoms, where to look, what to ask the seller

07F33A-FTV 3.3 V6 injector faults disrupting DPF regeneration

Check the multi-information display for DPF soot-level and regeneration history if accessible.diesel2021 onwardEngine
OccasionalEngine $1,500–$6,000 to fix

Does not apply

The 300 series' new 3.3 twin-turbo V6 diesel has had early reports of fuel injector faults which upset combustion and stop the DPF regenerating properly, leading to soot-loading warnings and limp mode. The engine is also named in Australian court action over emissions-system behaviour. Most affected vehicles are fixed under warranty, but as trucks age out of warranty an injector-plus-forced-regen bill lands on the owner.

A single common-rail diesel fuel injector photographed against a plain background.Example of the part — not this vehicle

A common-rail diesel injector. Contamination damages the nozzle at the tip.

Panoha · CC BY-SA 3.0 · Wikimedia Commons

Symptoms to notice

  • DPF warning light or frequent regeneration messages
  • Diesel smell and elevated idle during regens
  • Rough idle or misfire
  • Reduced power / limp mode

What to check

  1. Check the multi-information display for DPF soot-level and regeneration history if accessible.
  2. Ask for the service printout showing any injector or DPF-related warranty work.
  3. On the test drive include 20+ minutes of open-road running and watch for warning lights.

Where to look: Injectors under the engine cover; DPF in the exhaust under the vehicle, forward of the mid-point

Parts involved: Fuel injector, Diesel particulate filter.

Ask the seller

  • “Has it had any injector or DPF warranty work — can I see the dealer history?”
  • “Is it mostly driven short trips around town?”
  • “Is any factory warranty still remaining and transferable?”

08Timing Chain and Guide Wear (1FZ-FE 4.5L)

Cold-start the engine after it has sat overnight and immediately listen at the front of the engine for chain rattle.petrol1993–1997EngineRead the full fault: symptoms, where to look, what to ask the seller

09Glow Plug Seizure in Cylinder Head (1HZ 4.2L)

Ask specifically when glow plugs were last replaced and whether any were seized during removal.diesel1990–1997EngineRead the full fault: symptoms, where to look, what to ask the seller

102H / 12H-T diesel: tired injectors, glow plugs and start-up smoke

Ask the seller not to warm it up before you arrive — the cold start is the whole test on an old diesel, and a pre-warmed engine tells you nothing.diesel1980–1989EngineRead the full fault: symptoms, where to look, what to ask the seller

11Intercooler Hose Cracking and Boost Leaks (1HD-T 4.2L Turbo Diesel)

With the engine off, trace and physically squeeze all rubber hoses between the turbocharger compressor outlet, intercooler, and intake manifold.diesel1990–1997EngineRead the full fault: symptoms, where to look, what to ask the seller

12Thermostat Housing Cracking and Coolant Leak (1HZ 4.2L)

diesel1990–1997Cooling
OccasionalCooling $350–$950 to fix

Does not apply

The cast thermostat housing on the 1HZ engine is prone to cracking from thermal stress and electrolytic corrosion, particularly at the joint where it mates with the aluminium head and at the upper radiator hose connection. A cracked housing produces a coolant leak that worsens as the engine reaches operating temperature and contracts and expands. If not caught promptly, coolant loss leads to overheating.

An annotated photograph of an automotive engine thermostat identifying the wax capsule and both disc valves.Example of the part — not this vehicle

A double-valve engine thermostat, labelled: the wax capsule is what sticks.

Dougsim · CC BY-SA 3.0 · Wikimedia Commons

Symptoms to notice

  • Coolant weeping or dripping from the top front of the engine near the thermostat
  • White mineral deposits or dried coolant residue around the housing
  • Coolant puddle under the front of the engine after a run
  • Overheating if the leak is significant and undetected

What to check

After a full warm-up drive, inspect the thermostat housing (where the upper radiator hose connects at the front top of the engine) for any coolant weeping, white staining, or dried residue indicating a past or current leak. Check coolant level in the reservoir against the cold-fill mark.

Where to look: Front top of engine, thermostat housing at the upper radiator hose connection

Parts involved: Thermostat.

Ask the seller

  • “Has the thermostat or thermostat housing ever been replaced?”
  • “Any history of coolant leaks from the top of the engine?”
  • “When was the coolant last changed?”

13Oil consumption on early F33A-FTV engines running 0W-20

Check the dipstick/electronic oil level yourself and ask when oil was last added.diesel2021 onwardEngine
OccasionalEngine $100–$3,000 to fix

Does not apply

Some early 300-series diesels consume noticeable engine oil from low mileage, widely attributed to the very thin 0W-20 oil specified for economy. Toyota considers some consumption normal, but owners report topping up between services. It is mostly a monitoring cost rather than a failure, though ignoring a dropping level risks expensive damage on a new-generation engine.

Symptoms to notice

  • Oil level dropping between services
  • Low-oil warning on long trips
  • Occasional faint blue exhaust haze

What to check

  1. Check the dipstick/electronic oil level yourself and ask when oil was last added.
  2. Look for top-up oil bottles carried in the vehicle.
  3. Ask the selling dealer to document current consumption rate.

Where to look: Engine oil system — checked at the dipstick in the engine bay

Ask the seller

  • “How much oil does it use between services?”
  • “Has Toyota ever done an oil-consumption test on it?”
  • “What oil grade has been used?”

142UZ-FE 4.7 V8 Secondary Air Injection Pump Failure

Inspect the air pump for signs of corrosion or heat damage.petrol2006–2007Engine
CommonEngine $800–$2,200 to fix

Does not apply

The 2UZ-FE 4.7L V8 petrol engine is equipped with a secondary air injection system that pumps fresh air into the exhaust ports during cold start to reduce hydrocarbon and carbon monoxide emissions during catalyst light-off. The electric air pump draws air through a filter located in the engine bay and forces it through check valves into the exhaust manifold. The pump motor is susceptible to ingesting moisture during cold, wet starts, which corrodes the motor windings and causes premature failure. The check valves also fail open, allowing hot exhaust gas to backflow through the pump and destroy it. Failure triggers a stored P0410 or P0411 diagnostic trouble code and illuminates the check engine light, and the vehicle will fail emissions testing in markets where that applies.

Symptoms to notice

  • Check engine light illuminated with P0410 or P0411 diagnostic trouble codes stored in ECU memory
  • Audible grinding or rattling from the secondary air pump motor during cold start, indicating bearing or commutator failure
  • Pump motor completely inoperative — no sound on cold start, confirmed by relay actuation test

What to check

  1. Inspect the air pump for signs of corrosion or heat damage.
  2. Inspect the rubber air supply hose for collapse or burning.
  3. Test the pump relay and fuse.
  4. Inspect the air injection check valves for heat damage from exhaust backflow.
  5. If a workshop inspection is possible: Connect an OBD-II scan tool and check for stored or pending P0410 (Secondary Air Injection System Malfunction) or P0411 (Secondary Air Injection System Incorrect Flow Detected) codes.

Where to look: Engine bay, secondary air injection pump mounted near the battery or inner guard on the 4.7L V8

Parts involved: High-pressure fuel pump.

Ask the seller

  • “Is the check engine light currently on, or has it been reset recently?”
  • “Has any workshop retrieved diagnostic trouble codes from the vehicle?”
  • “Has the secondary air injection pump or check valves ever been replaced?”

1510-speed automatic harsh or hesitant shifting on early builds

Drive it in heavy-traffic conditions with lots of low-speed shifts, not just open road.diesel2021 onwardTransmission
OccasionalTransmission $200–$1,500 to fix

Does not apply

Early 300-series owners in Australia reported clunky low-speed shifts, hesitation and occasional harsh downshifts from the new 10-speed automatic, largely addressed by software recalibration at dealers. It is a drivability annoyance more than a failure, but confirm any updates have been done because out-of-warranty transmission diagnosis is expensive.

Symptoms to notice

  • Clunky 1-2 and 2-3 shifts in stop-start traffic
  • Hesitation when accelerating from a rolling stop
  • Occasional harsh downshift when braking

What to check

  1. Drive it in heavy-traffic conditions with lots of low-speed shifts, not just open road.
  2. Ask the dealer to confirm all transmission software campaigns are applied (they can check by VIN).

Where to look: Automatic transmission — behaviour felt through the driveline at low speeds

Ask the seller

  • “Have any transmission software updates or dealer reflashes been done?”
  • “Has it towed heavily?”
Electrical2

01Alternator mounted low on the V8 — killed by water crossings and mud

Look low at the front of the engine for mud staining and corrosion around the alternator.diesel2007–2021ElectricalRead the full fault: symptoms, where to look, what to ask the seller

02Dashboard wiring harness chafe recall (100 series Land Cruiser, 2002-2006)

Ask whether any fuses have blown or electrical items cut out.2002–2006Electrical
OccasionalElectrical $0 to fix

Does not apply

100 series Land Cruisers from the 2002 to 2006 model years were recalled (PRA 2008/10050) because a wiring harness under the dash can rub on a sharp edge of the pedal bracket on corrugated roads, wear through and blow fuses, cutting out electrical items. This applies to all engines. The fix is free at a Toyota dealer. This was an Australian recall; Japanese-import 100 series cars were not named in it, so ask a Toyota dealer to check the VIN.

Symptoms to notice

  • Fuses that keep blowing
  • Electrical items cutting out over rough roads

What to check

  1. Ask whether any fuses have blown or electrical items cut out.
  2. Check lights, wipers and dash work on the test drive.
  3. Ask the seller for the service history and look for a dealer invoice or service stamp showing recall PRA 2008/10050 (dash harness) was done.
  4. A buyer can also give the VIN to any franchise dealer and ask them to check for open recalls before paying.

Where to look: Under the dashboard near the pedal bracket

Ask the seller

  • “Has the dash wiring recall been done?”
  • “Have fuses ever blown for no clear reason?”
Body, brakes, suspension & interior2

0160-series chassis and body rust — the rear frame channel is the one that ends them

The 60-series is now forty-odd years old and rust, not mechanical wear, is what writes them off.1980–1989Body & RustRead the full fault: symptoms, where to look, what to ask the seller

0260-series front birfield joints and knuckle service

1980–1989SuspensionRead the full fault: symptoms, where to look, what to ask the seller
Fluid leaks1

01Power Steering Pump and Rack Seal Leaks

Check the power steering reservoir for correct fluid level and condition (should be clear, not dark).1990–1997Fluid Leaks
CommonFluid Leaks $600–$2,200 to fix

Does not apply

Power steering pump shaft seals and steering rack end seals deteriorate with age on the 80 series, causing leaks from minor weeping to significant fluid loss. A low-fluid pump produces a characteristic moan on full lock and can eventually fail, leaving the driver with heavy unassisted steering. The steering rack seals are labour-intensive to replace given the solid front axle layout, increasing repair costs.

Symptoms to notice

  • Power steering fluid puddle under the front of the vehicle after parking
  • Whining or groaning from the steering on full lock or at low speed
  • Stiff or heavy steering, particularly during parking manoeuvres
  • Visible oily residue or staining around the pump body or rack boots
  • Power steering reservoir requiring regular top-up

What to check

  1. Check the power steering reservoir for correct fluid level and condition (should be clear, not dark).
  2. Inspect the pump body and return line fittings for oily residue.
  3. Turn the steering fully lock-to-lock and listen for whining which indicates low fluid or pump wear.
  4. Inspect the rack boots at each end of the steering rack for swelling or oil leaking from tears.

Where to look: Power steering pump on engine front (driver's side), steering rack across the front axle

Parts involved: Steering rack.

Ask the seller

  • “Is the power steering fluid level correct and when was it last topped up?”
  • “Any recent power steering leaks or unusual noise on full lock?”
  • “Has the steering rack, rack seals, or pump been replaced?”

Toyota Land Cruiser faults in detail

Narrowed to the Toyota Land Cruiser · 2000. Each of these has its own page: the symptoms, where to look, what to ask the seller and what the repair costs. Free, no account needed.

1HD-FTE 4.2 Turbo Diesel Timing Belt FailureCritical · Engine1HD-FTE injector and injection pump wear at high mileageMajor · Engine1HZ timing belt, tensioner and water pump replacement overdue (interference: yes)Critical · EngineFront Lower Ball Joint and King Pin WearCritical · SuspensionHead Gasket Failure Due to Head Bolt Torque Loss (1HD-FTE 4.2L)Critical · EngineInjection Pump Plunger and Barrel Wear (1HD-FTE Denso VE Pump)Critical · EngineIntercooler Hose Cracking and Boost Leaks (1HD-FTE 4.2L Turbo)Major · EngineRust in tailgate, rear quarters, sills and chassis — NZ coastal / beach-launched examplesMajor · Body & Rust

What these repairs cost on other cars

Some of the Toyota Land Cruiser’s documented faults are repairs other models share. Each page lists the documented NZ cost for every model it affects.

Buying guides that cover the Toyota Land Cruiser

Other Toyota models

Toyota Prado64 documented faultsToyota RAV463 documented faultsToyota Hilux59 documented faultsToyota Prius42 documented faultsToyota Axio39 documented faultsToyota Estima38 documented faults

Toyota Land Cruiser buyer questions

Is the Toyota Land Cruiser reliable?

Like any used car, it depends on the specific example and its service history. Across the 42 documented faults for the Toyota Land Cruiser, the recurring problem areas are suspension, engine, and body & rust. A Toyota Land Cruiser with a full service history and no signs of the issues listed on this page can be a sound buy but each one needs to be checked individually before you commit.

What are the most common problems with a used Toyota Land Cruiser?

We've catalogued 42 known faults for the Toyota Land Cruiser, covering suspension, engine, and body & rust. All 42 are written out in full on this page, with the symptoms to notice, what to inspect, and typical repair costs for each. Free to read, no account needed.

How much do repairs cost on a Toyota Land Cruiser?

Most single repairs on the Toyota Land Cruiser fall between $800–$2,800 at NZ independent-workshop rates. Some of the 42 documented faults cost less and a few cost considerably more, and no one car needs them all. Knowing which ones to look for before you view is what lets you negotiate the price down or walk away.

Should I get a pre-purchase inspection on a Toyota Land Cruiser?

Yes. A Toyota Land Cruiser inspection focused on its known weak points is the single best way to avoid an expensive mistake. KickTyres gives you a guided, model-specific inspection plus a market valuation and negotiation figure for $24.90 far less than the cost of missing one of the faults on this page.