Skip to content
KickTyres
Ford2000–2022 Critical issues documented

Ford Mondeo MA: common faults & what to check

The MA is the Ford Mondeo built 2007–2015. It was sold here with the 2.0 turbo petrol, 2.0 diesel, and 2.3 petrol. Of the 15 faults documented for the Mondeo, 6 apply to this generation, each with its symptoms, what to inspect and a typical repair cost. Free, no account needed.

Check this exact Ford Mondeo

  • Odometer history
  • Money owing
  • Reported stolen
  • Ownership history
  • Official NZ vehicle register data
  • NZ owned and operated

Type the plate for the free basics. The full record is a paid check from $13.49, one car at a time, no subscription.

No NZ plate yet, or buying in Australia? Pick the generation and engine and start a free check below. New to KickTyres? How the check works →

15

Documented faults

Critical

Most serious

$800–$3,000

Typical repair

29

Service milestones

You're looking at the MA

3 engine variants are documented for this generation. Pick yours to narrow further, or keep reading for the generation as a whole.

Choose a different generation

Now narrow it to the engine

A 1.8 and a 2.4 of the same car do not fail the same way, so the faults below narrow to the engine as well as the year. Free, no account needed.

A 2007 Ford Mondeo is the MA generation (2007 to 2015).

Start your free check on this Ford Mondeo

No plate needed. You get the risk score, the buyer's checklist and the guided inspection for the exact car you picked above — not the whole nameplate.

Ford Mondeo MAEngine not picked yet

Pick the engine above first: the Mondeo came with 3, and without it the report has to show all of their faults. Pick the engine

Free. The paid plate check is separate, and stays optional.

Can't confirm for this car

Ford Mondeo · 2007

Narrowed to the year. No engine is recorded for this vehicle. Pick an engine to see which faults apply.

Tell us the engine, or check the engine code on the car, before relying on this.

  • No engine is recorded for this vehicle.

matched on year only

What to look out for

The checks worth doing on a Ford Mondeo before you hand over any money. Every documented fault is listed below, each with its own page.

  • Costly issue

    Inspect the ball joint boot for cracks or grease loss.

    See why

    Front lower control arm ball joint wear

    The front lower control arm ball joints on Mk3 through Mk5 Mondeos are a consumable with a typical lifespan of 80,000–130,000 km on NZ roads. The ball joint is pressed into the lower arm and is not separately serviceable on most variants — the entire arm must be replaced. Failure allows the front wheel to shift under cornering loads, causing directional instability and clonking over bumps.

    What you would notice

    • Clonking from the front suspension over bumps and when turning
    • Vague or wandering steering feel
    • Uneven tyre wear on the inner or outer front edge
    • Vehicle pulling to one side under heavy braking

    Typically $400–$900 to put right.

Ford Mondeo service schedule

The 5 engines a 2007 Ford Mondeo was sold with, each with its own intervals. Pick your engine above to narrow this to one. These are the model’s intervals — the car’s own service book is the only thing that can tell you what has actually been done to it.

Ford Mondeo Mk4 · 2007–2014 · 2.3L (Duratec) - LX / Zetec comfort trim

Petrol

Due by distance

  1. 150,000 km

    Check the cooling system hoses and radiator for minor weeping.

  2. 180,000 km

    Check the serpentine belt and tensioner assembly for fraying or bearing noise.

  3. 200,000 km

    Original suspension struts may have reached the end of their optimal dampening life, affecting ride quality.

Ford Mondeo Mk4 · 2007–2014 · 2.0L (Duratorq) - TDCi Diesel efficiency

Diesel

Due by distance

  1. 150,000 km

    Confirm the timing belt has been replaced if the vehicle is approaching this interval - proactive care matters with these engines.

  2. 200,000 km

    The DPF (Diesel Particulate Filter) system may need a professional clean or assessment to keep the exhaust breathing correctly.

Ford Mondeo Mk3 · 2001–2007 · 1.8L (Duratec) - Base fleet model

Petrol

Due by distance

  1. 150,000 km

    Suspension bushings and drop links may need replacing for better handling.

  2. 200,000 km

    Check the cooling system, looking for brittle hoses or radiator fatigue.

  3. 250,000 km

    Review the alternator and starter motor for reliable daily starting.

Ford Mondeo Mk3 · 2001–2007 · 2.0L (Duratec) - Popular NZ family trim

Petrol

Due by distance

  1. 150,000 km

    Suspension bushings and cooling system hoses have likely seen their best days; inspect and refresh.

  2. 200,000 km

    The alternator and starter motor often show age here, depending on the previous owner's driving frequency.

  3. 250,000 km

    A full check of the cooling system components and major seals keeps the Duratec engine running smoothly.

Ford Mondeo Mk3 · 2001–2007 · 2.5L (Duratec V6) - Ghia / ST220 performance

Petrol

Due by distance

  1. 150,000 km

    Check the cooling system components, specifically hoses and the radiator, for brittle plastics.

  2. 200,000 km

    Assess the alternator and starter motor; high-mileage examples may need a refresh of these electrical units.

  3. 250,000 km

    Inspect the suspension dampers and springs, which will likely have performed well beyond their original design life.

See all 6 issues for this oneDocumented for the exact year and engine you picked, including 1 rated critical.
Body, brakes, suspension & interior1

01Front lower control arm ball joint wear

Inspect the ball joint boot for cracks or grease loss.2000–2022Suspension
CommonSuspension $400–$900 to fix

The front lower control arm ball joints on Mk3 through Mk5 Mondeos are a consumable with a typical lifespan of 80,000–130,000 km on NZ roads. The ball joint is pressed into the lower arm and is not separately serviceable on most variants — the entire arm must be replaced. Failure allows the front wheel to shift under cornering loads, causing directional instability and clonking over bumps.

The front wheel of a car splayed outward with the lower control arm hanging down after a ball joint separation.Example of the part — not this vehicle

A separated lower ball joint: the control arm has dropped and the wheel has splayed out under the guard.

Elfix · CC0 · Wikimedia Commons

Symptoms to notice

  • Clonking from the front suspension over bumps and when turning
  • Vague or wandering steering feel
  • Uneven tyre wear on the inner or outer front edge
  • Vehicle pulling to one side under heavy braking

What to check

  1. Inspect the ball joint boot for cracks or grease loss.
  2. Check front tyre wear pattern across both sides.
  3. If a workshop inspection is possible: Lift the front of the car and apply upward pressure to the tyre at the 6 o'clock position — any vertical movement indicates ball joint wear.

Where to look: Front suspension lower control arm, inboard of front wheel

Parts involved: Ball joint.

Ask the seller

  • “When were the front lower control arms or ball joints last replaced?”
  • “Any clonking or knocking from the front suspension over bumps?”
  • “Has the car had an alignment check recently?”
Depends on the exact engine — 5 moreDocumented for a specific engine we could not confirm from what you picked. Check the engine code on the car.
Engine, transmission & cooling4

01Duratec 2.0 timing chain stretch and tensioner failure

Start the engine cold and listen immediately for chain rattle from the front timing cover.petrol2000–2014Engine
CommonEngine $1,800–$3,500 to fix

Can't confirm for this car

The 2.0L Duratec petrol engine fitted to Mk3 and Mk4 Mondeos develops timing chain stretch and tensioner wear with age, particularly above 150,000 km. A worn chain can skip teeth on the camshaft sprockets, causing misfires, loss of power, and in severe cases catastrophic valve-to-piston contact. The hydraulic tensioner is a documented weak point that loses pressure when oil is degraded.

The front of a dual overhead camshaft engine with the timing cover removed, exposing the timing chain and sprockets.Example of the part — not this vehicle

The front of a twin-cam engine with the timing cover off — chain, sprockets and guides.

Logansenf · CC BY-SA 4.0 · Wikimedia Commons

Symptoms to notice

  • Cold-start rattling from front of engine that fades after warm-up
  • Check engine light with camshaft position sensor codes (P0340, P0345)
  • Rough idle and misfires at idle
  • Loss of power across the rev range

What to check

  1. Start the engine cold and listen immediately for chain rattle from the front timing cover.
  2. Scan for cam/crank correlation codes.
  3. Check service history for oil change frequency — neglected oil accelerates tensioner wear.

Where to look: Front of engine, behind timing cover

Parts involved: Timing chain.

Ask the seller

  • “Has the timing chain or tensioner ever been replaced?”
  • “What is the oil change interval — was it kept under 10,000 km?”
  • “Any cold-start rattling when you first start the car?”

02Dual-mass flywheel failure on TDCi manual transmission

With the engine idling in neutral, depress the clutch and listen for a rattle or rumble that disappears when the pedal is released.diesel2000–2014TransmissionRead the full fault: symptoms, where to look, what to ask the seller

03Blocked diesel particulate filter (DPF) and fuel vaporiser failure on short trips

Ask how the car has been used - a diesel driven only on short suburban trips is a red flag.diesel2007–2014EngineRead the full fault: symptoms, where to look, what to ask the seller

04TDCi EGR valve carbon fouling and failure

Scan for EGR flow and position codes.diesel2000–2022EngineRead the full fault: symptoms, where to look, what to ask the seller
Fluid leaks1

01TDCi high-pressure fuel injector copper seal failure

With the engine running, listen for injector ticking and inspect each injector's entry point to the cylinder head for carbon deposits or sooting.diesel2000–2014Fluid LeaksRead the full fault: symptoms, where to look, what to ask the seller
Other Ford Mondeo engines and years9 documented issues that do not apply to the one you picked.
Engine, transmission & cooling6

012.0 EcoBoost coolant intrusion into the cylinders (open-deck block)

Check the coolant reservoir level and look for it sitting low with no leak on the driveway.petrol2015–2020Engine
OccasionalEngine $2,500–$8,000 to fix

Does not apply

The Mk5 petrol Mondeo's 2.0 EcoBoost uses an open-deck aluminium block, and these four-cylinder EcoBoost engines are prone to coolant seeping internally between the block and head into the cylinders. Coolant slowly disappears with no puddle on the ground, and in bad cases it fouls a cylinder, causing rough running, white exhaust smoke and overheating. Ford's proper fix is a short/long-block replacement, which is a very expensive job. It is a design-related issue Ford has acknowledged in service bulletins for the 2.0 EcoBoost family.

Symptoms to notice

  • Coolant level drops with no visible leak
  • White/sweet-smelling smoke from the exhaust
  • Milky residue under the oil cap or overheating
  • Rough running or misfire on one cylinder

What to check

  1. Check the coolant reservoir level and look for it sitting low with no leak on the driveway.
  2. Pull the oil filler cap and look for a mayonnaise-like film (a sign coolant is mixing in).
  3. On the test drive watch the temperature gauge and the exhaust for white smoke once warm.
  4. Ask whether the car has needed regular coolant top-ups.

Where to look: Inside the engine, the seal between the cylinder block and head

Ask the seller

  • “Does the coolant ever need topping up, and how often?”
  • “Has it ever run hot or had white smoke from the exhaust?”

022.0 EcoBoost Timing Chain Tensioner Wear

petrol2013–2019Engine
OccasionalEngine $2,200–$5,500 to fix

Does not apply

The 2.0L EcoBoost (EcoBoost 2.0T) fitted to the Mondeo Mk5 uses a hydraulic timing chain tensioner that relies on adequate oil pressure and viscosity to maintain chain tension. The primary chain and its tensioner exhibit wear from cold-start oil starvation caused by delayed pressure build-up in the tensioner circuit. Over time the tensioner loses its ability to take up slack, allowing the chain to slap against the plastic guide rails. If left unaddressed the guides fracture, chain tension is lost entirely, and catastrophic valve-to-piston contact can occur. The failure rate is substantially higher in vehicles operated on extended oil change intervals or with oil consumption issues.

The front of a dual overhead camshaft engine with the timing cover removed, exposing the timing chain and sprockets.Example of the part — not this vehicle

The front of a twin-cam engine with the timing cover off — chain, sprockets and guides.

Logansenf · CC BY-SA 4.0 · Wikimedia Commons

Symptoms to notice

  • Metallic rattling noise from front of engine on cold start lasting 5–20 seconds
  • Rattle diminishes or disappears once oil pressure builds at operating temperature
  • Engine management warning light with variable valve timing fault codes
  • Rough idle or hesitation linked to timing chain stretch fault P0016/P0017
  • Ticking or whirring from valve cover area at idle

What to check

  1. Cold-start the engine immediately and listen from the passenger side of the engine bay for a metallic rattle lasting more than 3 seconds before fading.
  2. Scan for stored codes P0016, P0017, P0022.
  3. Review oil service history — chains fail faster on engines run past 10,000 km oil intervals.
  4. Inspect valve cover area for oil leaks suggesting gasket degradation that coincides with chain wear.

Where to look: Front of engine, primary timing chain, tensioner on driver's side of block, upper and lower guide rails

Parts involved: Timing chain.

Ask the seller

  • “Has the timing chain or tensioner ever been inspected or replaced?”
  • “Has the vehicle been serviced strictly within Ford recommended oil change intervals?”
  • “Has there ever been a rattle on cold start that disappeared after warm-up?”
  • “Has the oil level ever dropped between services indicating consumption?”

03PowerShift 6DCT450 dual-clutch judder, shift shock and mechatronic faults

Turbo-petrol and diesel Mondeos fitted with the automatic use Ford's PowerShift, a 6-speed dual-clutch (the 6DCT450 wet-clutch unit).2010–2020TransmissionRead the full fault: symptoms, where to look, what to ask the seller

04EcoBoost 1.5T timing chain tensioner rattle on cold start

Cold-start the engine after it has been sitting overnight and listen immediately for chain rattle from the front of the engine.petrol2014–2022EngineRead the full fault: symptoms, where to look, what to ask the seller

052.0 TDCi diesel particulate filter blockage

Scan for DPF soot load percentage using a Ford IDS-compatible scanner.diesel2014–2022EngineRead the full fault: symptoms, where to look, what to ask the seller

06Diesel AdBlue/NOx sensor faults and continued injector wear (Mk5 TDCi)

Look for any AdBlue or emissions warnings on the dash at start-up.diesel2015–2020Engine
OccasionalEngine $400–$1,500 to fix

Does not apply

Mk5 Mondeo diesels fitted with an AdBlue (SCR) exhaust system commonly throw NOx sensor and AdBlue-system warnings, which can restrict performance or, on some markets, threaten a no-restart countdown until the fault is fixed. NOx sensors are pricey to replace. The same TDCi injector and DPF weaknesses carried over from the Mk4 also apply, so a Mk5 diesel with warning lights needs a proper diagnostic before purchase rather than a code-clear.

A single common-rail diesel fuel injector photographed against a plain background.Example of the part — not this vehicle

A common-rail diesel injector. Contamination damages the nozzle at the tip.

Panoha · CC BY-SA 3.0 · Wikimedia Commons

Symptoms to notice

  • AdBlue or 'exhaust fault - restart in xxx km' warning
  • Engine or emissions warning light
  • Reduced power / limp mode
  • Prompts to refill AdBlue

What to check

  1. Look for any AdBlue or emissions warnings on the dash at start-up.
  2. Ask if the AdBlue tank is topped up and whether any NOx sensor work has been done.
  3. Have the car scanned for NOx sensor and SCR codes - a recently cleared fault often returns within a few drives.

Where to look: NOx sensors and SCR catalyst in the exhaust; AdBlue tank usually near the fuel filler or under the car

Parts involved: Fuel injector.

Ask the seller

  • “Has this car ever shown an AdBlue or emissions warning?”
  • “Have any NOx sensors been replaced recently?”
Electrical1

012.0 Hybrid HV Battery Module Capacity Failure

Request a hybrid battery state-of-health report from a Ford dealer — IDS can display individual module voltages.hybrid2014–2019Electrical
OccasionalElectrical $3,500–$9,000 to fix

Does not apply

The Mondeo/Fusion Hybrid uses a 1.4 kWh nickel-metal hydride (NiMH) high-voltage battery pack mounted beneath the rear seat. Individual cell modules within the pack degrade unevenly; when one module reaches a state-of-health threshold below approximately 70% the battery management system restricts the usable capacity of the entire pack to prevent thermal imbalance. This manifests as a dramatic reduction in EV assist range and regenerative braking effectiveness. In advanced cases a cell group fails completely, triggering the orange triangle warning and reducing the vehicle to a limp-home charge-sustain mode with markedly higher fuel consumption. The failure is accelerated by exposure to sustained high ambient temperatures and vehicles that sat unused for extended periods allowing deep self-discharge.

Symptoms to notice

  • Fuel consumption significantly higher than Ford specification
  • Orange triangle or wrench warning light on dash
  • EV gauge shows minimal or no battery charge even after highway driving
  • Engine runs constantly with no EV assist at low speeds
  • Reduced or absent regenerative braking feel when lifting throttle

What to check

  1. Request a hybrid battery state-of-health report from a Ford dealer — IDS can display individual module voltages.
  2. Note fuel consumption from service records; degraded packs show 15–25% higher real-world fuel use.
  3. Inspect rear seat base for evidence of prior battery access or replacement.
  4. If a workshop inspection is possible: Scan high-voltage system with Ford IDS or compatible OBD tool for HV battery DTC codes B1318, U3000, or P0A80.

Where to look: High-voltage NiMH battery pack under rear seat squab, power control module in boot area

Ask the seller

  • “Has the hybrid battery ever been tested for state of health at a Ford dealer?”
  • “Has fuel consumption increased noticeably over the life of the vehicle?”
  • “Has the orange triangle or hybrid system warning ever illuminated?”
  • “Has the vehicle ever been left unused for more than 4–6 weeks?”
Body, brakes, suspension & interior2

01Panoramic Sunroof Drain Blockage — Water Ingress

Press carpet under all four footwell mats and check for moisture.2014–2019Body & Rust
CommonBody & Rust $500–$4,000 to fix

Does not apply

The Mondeo Mk5 fitted with the full-length panoramic roof shares the same narrow-bore corner drain architecture as the Kuga. Drains route from sunroof channels through A and C pillars, and blockage by debris causes water to overflow into the headliner and pillar cavities. In the Mondeo the drain failure is particularly consequential because water reaches the front and rear footwell BCM modules, the SYNC 3 infotainment ECU located beneath the central console, and in some cases the transmission control module mounted in the engine bay but with wiring looms passing through the A-pillar cavity. Electrical gremlins including infotainment resets, gear selector faults, and false ABS warnings are linked to this ingress pattern.

Symptoms to notice

  • Wet front or rear footwell carpet after rain
  • SYNC infotainment spontaneous reboots or blank screen
  • Musty odour from climate system vents
  • Staining along headliner edges or sail panel area
  • Intermittent ABS, transmission, or airbag warning lights

What to check

  1. Press carpet under all four footwell mats and check for moisture.
  2. Inspect C-pillar trim bases for tide marks.
  3. Test sunroof drain flow by pouring water into each corner channel with sunroof open and confirm drainage exits under car within seconds.
  4. Pull back front carpet edges to check for mould or rust on floor pan.
  5. Inspect SYNC module under centre console for corrosion.

Where to look: Panoramic roof corner drains, A and C pillar cavities, front and rear footwells, SYNC module under centre stack

Ask the seller

  • “Has the panoramic roof drain system been serviced or flushed?”
  • “Has there been any damp smell or wet carpet?”
  • “Have there been electrical faults with the infotainment or warning lights?”
  • “Has any interior trim, carpet, or electrical module been replaced?”

02Rear Wheel Bearing Premature Failure

Rotate wheels by hand listening for roughness.2013–2019Suspension
CommonSuspension $500–$1,200 to fix

Does not apply

The Mondeo Mk5 rear suspension uses a multi-link arrangement with a sealed hub bearing unit that is notably susceptible to premature wear on New Zealand and Australian roads. The bearing is a two-row angular contact design that handles both radial load from vehicle weight and axial load during cornering; the sealing effectiveness degrades in environments with high humidity and road salt, allowing moisture and fine abrasive particles to enter the bearing races. On FWD models the bearings still carry substantial cornering loads via the independent rear geometry. Failure follows a progressive pattern from faint hum to loud drone, followed by ABS sensor errors as bearing play introduces runout into the tone ring, with eventual risk of brake pulsation and wheel separation in severe neglect cases.

Symptoms to notice

  • Cyclic droning or humming from rear escalating with vehicle speed above 70 km/h
  • Noise varies when gentle lateral weight transfer applied in motorway lane change
  • ABS or DSC warning light after bearing develops excessive runout
  • Vibration through rear seat at highway speed
  • Roughness felt when spinning rear wheel by hand on hoist

What to check

  1. Rotate wheels by hand listening for roughness.
  2. Test drive on smooth motorway surface and note any drone altering with gentle weaving.
  3. Scan ABS module for wheel speed sensor codes that indicate bearing runout.
  4. If a workshop inspection is possible: On a hoist grasp each rear wheel at 12 and 6 o'clock and at 3 and 9 o'clock positions and attempt to detect play in both planes.

Where to look: Rear hub bearing assemblies, pressed into multi-link rear knuckle, both sides

Parts involved: Wheel bearing.

Ask the seller

  • “Has either rear wheel bearing been replaced?”
  • “Is there any droning noise at highway speed?”
  • “Have ABS or stability control lights ever appeared without an obvious cause?”
  • “Has the vehicle been used near coastal areas where road salt is common?”

Ford Mondeo faults in detail

Narrowed to the Ford Mondeo · 2007. Each of these has its own page: the symptoms, where to look, what to ask the seller and what the repair costs. Free, no account needed.

Blocked diesel particulate filter (DPF) and fuel vaporiser failure on short tripsMajor · EngineDual-mass flywheel failure on TDCi manual transmissionMajor · TransmissionTDCi EGR valve carbon fouling and failureMajor · EngineTDCi high-pressure fuel injector copper seal failureMajor · Fluid Leaks

What these repairs cost on other cars

Some of the Ford Mondeo’s documented faults are repairs other models share. Each page lists the documented NZ cost for every model it affects.

Buying guides that cover the Ford Mondeo

Other Ford models

Ford Ranger45 documented faultsFord Focus37 documented faultsFord Falcon36 documented faultsFord XR813 documented faultsFord Explorer11 documented faultsFord Fusion11 documented faults

Ford Mondeo buyer questions

Is the Ford Mondeo reliable?

Like any used car, it depends on the specific example and its service history. Across the 15 documented faults for the Ford Mondeo, the recurring problem areas are engine, electrical, and transmission. A Ford Mondeo with a full service history and no signs of the issues listed on this page can be a sound buy but each one needs to be checked individually before you commit.

What are the most common problems with a used Ford Mondeo?

We've catalogued 15 known faults for the Ford Mondeo, covering engine, electrical, and transmission. All 15 are written out in full on this page, with the symptoms to notice, what to inspect, and typical repair costs for each. Free to read, no account needed.

How much do repairs cost on a Ford Mondeo?

Most single repairs on the Ford Mondeo fall between $800–$3,000 at NZ independent-workshop rates. Some of the 15 documented faults cost less and a few cost considerably more, and no one car needs them all. Knowing which ones to look for before you view is what lets you negotiate the price down or walk away.

Should I get a pre-purchase inspection on a Ford Mondeo?

Yes. A Ford Mondeo inspection focused on its known weak points is the single best way to avoid an expensive mistake. KickTyres gives you a guided, model-specific inspection plus a market valuation and negotiation figure for $24.90 far less than the cost of missing one of the faults on this page.